Edelbrock 4100 Series Installation Instructions
Catalog #4100, 4200, & 4400 Series
Rev. 3/06 - RS/mc
©2006 Edelbrock Corporation
Brochure #63-0471
1
EDELBROCK VALVE COVERS
Catalog #4100, 4200, & 4400 Series
INSTALLATION INSTRUCTIONS
®
PLEASE study these instructions carefully before beginning this installation. Most installations can be accomplished with common tools and
procedures. However, you should be familiar with and comfortable working on your vehicle. If you do not feel comfortable performing this
installation, it is recommended to have the installation completed by a qualified mechanic. If you have any questions, please call our Technical
Hotline at: 1-800-416-8628, 7:00 am - 5:00 pm, Pacific Standard Time, Monday through Friday or e-mail us at Edelbrock@Edelbrock.com.
IMPORTANT NOTE: Proper installation is the responsibility of the installer. Improper installation
will void your warranty and may result in poor performance and engine or vehicle damage.
Please complete and mail your warranty card. Be sure to write the model number of this product in the "Part #____" space. THANK YOU.
DESCRIPTION: Edelbrock offers several valve covers for several engine models. See catalog for application listing. Installation is the same as
original equipment valve covers. Aluminum models are available in various finishes including EnduraShine™ and PermaStar®. All aluminum
covers require that baffles be installed if breathers are used. Some racing valve covers require that holes be machined for breathers if breathers
are desired. Signature Series valve covers include baffles. Check for clearance between baffles and rocker arms. Trim baffles slightly if necessary.
INSTALLATION NOTES FOR ALUMINUM VALVE COVERS (4100 & 4200 SERIES PART NUMBERS):
•
For applications using breathers/PCV, attach the breather baffles using the supplied drive pins. Using a punch and hammer, tap pins in until
fully seated
(See Fig. 1). On valve covers without breather holes, the breather holes must be drilled/machined before attaching the baffles.
CAUTION!: WHEN DRIVING THE PINS INTO THE VALVE COVER, YOU MUST SUPPORT THE BACK SIDE OF THE VALVE COVER WITH A BLOCK OF WOOD,
OR OTHER NON-MARRING SURFACE. FAILURE TO DO SO COULD RESULT IN DAMAGE TO THE COVER, SUCH AS CRACKS, DENTS, ETC. (See Fig. 1).
Recessed Baffles: Some valve covers include baffles with a curved recess across them. Make note of the position of the baffle. The recess
in the baffle plate should be positioned as shown below
(See Fig. 2).
•
Breather Knockouts: Centerbolt covers are intended for use with OEM breather and PCV valve. If the application calls for non-OEM push-
in breathers, remove the “knockout ring” from the breather holes using a hammer and a large punch. Be sure to support the perimeter of
the breather hole with a large socket, or block of wood. Perform this procedure BEFORE installing the breather baffles.
•
Pontiac: Elite Valve Covers #4256 for Pontiac V8s will require that spacers be used to provide clearance for the A/C compressor bracket.
Install the spacers under the bracket at the intake manifold.
•
Small Block Chevrolet: 1986 and earlier Small block Chevrolet engines with EGR may require #1476 and/or GM #14031368 spacers to
provide clearance for the EGR valve, especially with “tall profile” valve covers.
Fig 1. - Baffle Plate Installation
Support the back of the valve cover while
tapping drive pins into place.
Drive Pins Are
Flush With
Baffle Plate
Support
Block
Note Recess In Baffle
Drive Pins
Fig. 2 - Recessed Baffle Installation
Make sure recess faces out, and the curved portion faces
towards the side closest to the intake manifold.
Edelbrock Corporation • 2700 California St. • Torrance, CA 90503
Tech-Line: 800-416-8628 • E-Mail: Edelbrock@Edelbrock.com