1. DL manuals
  2. Eden
  3. IP Access Controllers
  4. PACK SOLO
  5. Technical Manual

Eden PACK SOLO Technical Manual

Manual is about: Standalone Biometric reader

Summary of PACK SOLO

  • Page 1

    Access control pack solo standalone biometric reader technical manual.

  • Page 2

    Technical manual packsolo – v1.5 p.2/24 contents contents ......................................................................................................................... 2 warning .................................................................................................................

  • Page 3

    Technical manual packsolo – v1.5 p.3/24 warning caution: this product is designed to work only in a standalone mode.

  • Page 4

    Technical manual packsolo – v1.5 p.4/24 acknowledgement dear client, you have just purchased a “packsolo” reader with remote control opening built by the french company eden innovations. The entire eden innovations team would like to thank you for your interest as well as your confidence in our secu...

  • Page 5

    Technical manual packsolo – v1.5 p.5/24 information and recommendations pursuant to european directive ute c00-200, incorporating directives 89/336 eec and 92/31 eec, packsolo complies with the following standards: nf en 50081-1 governing electromagnetic radiation, and nf en 50082-1 governing electr...

  • Page 6

    Technical manual packsolo – v1.5 p.6/24 technical characteristics 1) biometric reader maximum power consumption ........ 300ma @12v power supply voltage ...................... 9 – 14vdc weight ............................................. 175 g housing dimensions ........................ 119 x 77 x ...

  • Page 7

    Technical manual packsolo – v1.5 p.7/24 wiring diagram 3) connecting the reader to the control module data sheet: 4 wires (3 pairs recommended) 1200 m (2730 ft) Ø 0.6 mm (1/30 in) (syt recommended) characteristic: sensitive connection screen: mandatory to achieve 1200 m (2730 ft), you need to instal...

  • Page 8

    Technical manual packsolo – v1.5 p.8/24 4) connecting to a third party intrusion control unit 5) connecting an exit push button and a door contact note: to connect a third party intrusion control unit, ensure that a common earth is connected between the control module and the control unit. If the in...

  • Page 9

    Technical manual packsolo – v1.5 p.9/24 6) switch configuration the control module has 3 configuration switches: switches 1 and 2: configuration of the time delay for the opening control switch 3: configuration of the “alarm activation/inactivation” output (activation/inactivation of a third party i...

  • Page 10

    Technical manual packsolo – v1.5 p.10/24 7) power failure door activator note: in order to avoid any random malfunctions that may interfere with the correct use of the system caused by return currents, it is essential to use and connect the non-return diodes supplied with the product in accordance w...

  • Page 11

    Technical manual packsolo – v1.5 p.11/24 9) standard door activator: triggered by a voltage pulse note: in order to avoid any random malfunctions that may interfere with the correct use of the system caused by return currents, it is essential to use and connect the non-return diodes supplied with th...

  • Page 12

    Technical manual packsolo – v1.5 p.12/24 initial power-on – factory configuration when you first start the product, you need to register the 3 configuration cards ( add , add alarm and delete ) with the reader in order to activate it. To do this, follow the procedure below: after this stage, your pr...

  • Page 13

    Technical manual packsolo – v1.5 p.13/24 installation of more than one reader on the same site if you use the badge with fingerprint access for several readers on the same site, so as to remember the same code for each reader (therefore to not repeat the addition of badges on each reader), you must ...

  • Page 14

    Technical manual packsolo – v1.5 p.14/24 user management 1) add a user with a badge plus fingerprint present the add badge at the same time as the badge for the user you wish to add you have 10 seconds to present the first finger of the user to be added 3 times you have 10 seconds to present the sec...

  • Page 15

    Technical manual packsolo – v1.5 p.15/24 2) add a user with badge only 3) add user with a fingerprint only present the add badge you have 10 seconds to present 3 times the first finger of the user to be added you have 10 seconds to present 3 times the second finger of the user to be added (if you on...

  • Page 16

    Technical manual packsolo – v1.5 p.16/24 4) add an “alarm” user with a badge and fingerprint note: an “alarm” user can, by presenting his/her second fingerprint, activate or inactivate a third party alarm system. You have 10 seconds to present the access finger of the user to be added 3 times you ha...

  • Page 17

    Technical manual packsolo – v1.5 p.17/24 5) add an “alarm” user with fingerprint only 6) deleting a badge present the add alarm badge you have 10 seconds to present the access finger of the user to be added 3 times you have 10 seconds to present the alarm finger of the user to be added 3 times (if y...

  • Page 18

    Technical manual packsolo – v1.5 p.18/24 7) deleting a user with fingerprint only 8) deleting all users (fingerprints and badges only) present the delete badge you have 10 seconds to present one of the 2 fingers of the user to be deleted. If the user is recognised, he/she will immediately be deleted...

  • Page 19

    Technical manual packsolo – v1.5 p.19/24 restore to factory settings note : should you lose your configuration badges, you need to reset the reader to its factory settings in order to register a new set of configuration badges. This process will delete all the users (fingerprints only and badges). T...

  • Page 20

    Technical manual packsolo – v1.5 p.20/24 signaling leds an explanation of the different status of the blue and green leds: blue led green led reader status flashing alternately reader in factory configuration: waiting for configuration badges/cards ( add , add alarm , delete ) flashing off normal op...

  • Page 21

    Technical manual packsolo – v1.5 p.21/24 connector blocks.

  • Page 22

    Technical manual packsolo – v1.5 p.22/24 check list pack solo serial number : id number : gasket : torx bit : torx screw : bag : wall seal :.

  • Page 23

    Technical manual packsolo – v1.5 p.23/24 technical support: hotline@eden-innovations.Com notes ------------------------------------------------------------------------------------------------------------------------------- -----------------------------------------------------------------------------...

  • Page 24

    Zone commerciale et artisanale 670, route de berre 13510 eguilles france www.Eden-innovations.Com.