- DL manuals
- Eden
- Accessories
- UPS Freemont
- Assembly Manual
Eden UPS Freemont Assembly Manual
Summary of UPS Freemont
Page 1
12 x 12 flat top pergola w w w. E d e n a r b o r s. Co m a s s e m b l y g u i d e o p t i o n a l a c c e s s o r y • bolt down bracket kit (4 for pergola) ver 1.2/oct 2011 model: freemont.
Page 2
Ta b l e o f c o n t e n t s 2 12 x 12 flat top pergola 3 www.Edenarbors.Com 1 2 x 1 2 f l a t to p p e r g o l a introduction & overview ……………………………. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .………. . . . . . Pergola materials overview ………………………. . ....
Page 3
I n t r o d u c t i o n & o v e r v i e w 3 12 x 12 flat top pergola getting started first off, allow us to say thank you for the investment you have made in one of our fine pergola kits. This kit is designed to be assembled and installed ideally by two people with basic carpentry knowledge and tool...
Page 4
4 12 x12 flat top pergola www.Edenarbors.Com top view front view side view 94 in 145.35 in 164 in 171.5 in 8.73 in 25.8 in 88 in 134 in 100 in 105 3/4 in freemont pergola materials overview 6 1 2 4 3 9 1. Post caps (2) 2. Main column tops (2) 3. Post trims (4) 4. Rafter & beam decorative end caps (1...
Page 5
Check boxes (total of 5) for these contents in the event of missing or defective parts please call our customer service dept. At 1 800 282 9346, ext #20 (mon. To fri. 8:00 am to 4:00 pm est). 1. Main column bottoms (2) 2. Main column tops (2) 3. Beam & rafter joiners (8) 4. One way 4”x4” internal wo...
Page 6
Pergola additional materials list www.Edenarbors.Com hardware (in plastic bag) note: we have included 10% extra screws beyond what is identified below. All screws included with this kit are self-auguring. A. Vinyl weld glue (3) b. 2 1/2” self-auguring stainless steel screws (16) (to lock vinyl colum...
Page 7: For Attached Pergola
Wood post layout & installation for attached pergola measure and mark out the location of the pergola posts using string line and temporary wood stakes. Adjust string lines accordingly. The inside corner of the string lines will be the post location. Please note: should you decide to moderately modi...
Page 8
Wood post layout & installation using bolt down brackets for concrete or wood surface for attached pergola measure and mark out the location of the pergola posts using string or chalk line. Adjust string lines accordingly. The inside corner of the string lines will be the post location. Mark out the...
Page 9: Over Wood Posts
Vinyl column assembly & installation over wood posts 9 12 x 12 flat top pergola 1 using the vinyl weld glue, insert the one way 4”x4” internal wood post guide in the one end of the main column posts. This step is only applicable if your wood 4x4 post are embedded into the ground. If your pergola is ...
Page 10: Vinyl Beam Assembly
134 in. 340.4 cm. 146 7/8 in. 373 cm. Vinyl beam assembly 1 www.Edenarbors.Com insert one 2x6x12 pressure treated wood into a beam followed by the joiner and another beam section. Critical note: note the location of the pre-drilled holes on beams. As pictured aside, the further distanced holes need ...
Page 11: Vinyl Rafter Assembly
Www.Edenarbors.Com 11 12 x 12 flat top pergola 1 vinyl rafter assembly insert one 2x6x12 pressure treated wood into a rafter section followed by the joiner and another rafter section. Screw the joiner to vinyl rafters and wood insert using 1 1/2” screws. Repeat steps 1 and 2 for the remainder of the...
Page 12
Vinyl beams & rafter placement 12 12 x 12 flat top pergola using a helper and two ladders proceed to complete the following steps: slide the vinyl beam with rafter clips pre-installed through both holes of the vinyl column (overshooting), and then back through both holes of the opposite column. Plea...
Page 13
Vinyl beams & rafter placement 13 12 x 12 flat top pergola using a helper and two ladders proceed to complete the following steps: mount the other pergola beam which has the rafter hangers onto the wood beam as shown. The top of the wood beam should be flush with the top of the pergola beam. Align t...
Page 14
Fastening pergola ends and caps 14 12 x 12 flat top pergola install decorative pergola end caps using vinyl weld. Install the post caps using vinyl weld. Final position your post trims. 1 2 3 s t e p e i g h t 2 1 to position post trim in place: 1. Slide the post trim down. 2. Apply a generous amoun...
Page 15: 1 5
The 1 1/2 x 1 1/2 shade slats are designed to be installed with 8 3/4” spacing between each slat. Shade slats are designed to extend approximately 8 1/4” past the last rafter. Measurement includes the pre-installed pergola ends. Your goal is to ensure that all the shade slats overhang equally to the...