1. DL manuals
  2. Eden
  3. Musical Instrument Amplifier
  4. World Tour 1205
  5. Operation Manual

Eden World Tour 1205 Operation Manual

Summary of World Tour 1205

  • Page 1

    The leader in bass amplification. World tour 1205 bass guitar amplifier operation manual never compromise™ ©09-20-2005 by u.S. Music corp..

  • Page 2: Bass Guitar Amplifier

    2 bass guitar amplifier wt1205 operation manual publishing date 09-20-2005 forward congratulations on the purchase of your new eden world tour integrated amplifier system. All of us at eden are totally committed to providing you with the very best bass guitar systems in their class. Our goals are to...

  • Page 3: Caution!

    3 the eden world tour products group is the result of our quest for ultimate bass tone and maximum reliability. Your new world tour amplifier was designed, engineered and manufactured equivalent to aircraft vibration standards and housed in a one-piece aluminum case with steel top to ensure maximum ...

  • Page 4

    4 front panel features input jacks – designed to accept a standard ¼ inch mono phone plug. For best results use a high quality shielded cable to connect your instrument to the amplifier. Both inputs are buffered and will handle standard passive, high level active, and piezo input signals. Both jacks...

  • Page 5

    5 compressor active indicators – light to indicate that the signal has crossed the threshold of the compression circuit and that compression is taking place. Enhance controls – called the “magic knob” by some, this complex control simultaneously boosts the very low bass, upper middle, and high frequ...

  • Page 6

    6 we recommend you engage these switches at low volumes so that your sound remains consistent at any volume. At higher volume levels they aren’t needed but you may want to use them as a matter of taste. Because we strongly support freedom of choice, we’ve incorporated these two switches into our des...

  • Page 7

    7 mains on/off switch – this switch turns the system power on or off. The switch illuminates to indicate the presence of ac power present in the chassis. This switch is prior to the fuse. The switch light can be on even if the fuse is blown. The light in the switch may flicker depending on local vol...

  • Page 8

    8 all models come with a holder marked (fuse) or (115/230) and are factory configured for 100/120/ 230/240 only and must be adapted by a service tech for any voltage change. Fuse requirements: usa @ 120 volts /60 hz – 10 amps, 5 x 20 mm gmc/t/slow blow europe @ 240 volts/50 hz - 5 amps, 5 x 20 mm gm...

  • Page 9

    9 footswitch jack – connect the footswitch here. When connected, the footswitch overrides the corresponding front panel controls. Tuner out jack – this standard ¼ inch jack is designed to provide a pre- gain signal for connection to a tuner. It can also be used to provide pre-tone signal to other de...

  • Page 10

    10 cooling system – your amplifier features a thermostatically controlled fan, which will switch on when the internal temperature reaches 130 degrees f. In low volume situations (into 8 ohm loads) the fan may not come on at all. The cooling system also features a high temperature thermal safety syst...

  • Page 11

    11 dual (stereo) channel operation – engage this switch when using stereo instruments. Engaging this switch will bypass the channel switching. Turbo boost – also known as the solo button, this engages a +6db boost to put you on top of the mix. Use this for solos and such. This control is global, mea...

  • Page 12

    12 speaker connections – if you are using the amplifiers separately, connect a speaker to each amp. Do not use the bridge mono speaker connection and make sure the bridge mono switch on the front panel is disengaged. If desired, you may use a single amplifier to run a single speaker. If you are usin...

  • Page 13

    13 once you’ve ensured correct voltage and speaker connection, set the master volume control to minimum (fully counter-clockwise). Set the tone controls to the center position (12:00 or 0). Turn the enhance controls to the minimum position. Set the input gain controls to the minimum (fully counter-c...

  • Page 14

    14 setting the compressor – if you want to use compression, engage it now by turning up the compressor threshold control. The compressor light will blink when your gain goes above the compression threshold. This will generally show up more on the lower notes, or when you employ slapping. (a properly...

  • Page 15

    15 using the eq controls – before you begin to twiddle knobs, let’s talk about a few things. Excessive boosting of one or more eq frequencies may cause an overload in the eq section. If this happens, the clip light will engage. This is a very bad thing and needs to be corrected immediately. If eq cl...

  • Page 16

    16 we suggest you do some experimenting with the midrange controls to better understand how they can affect your tone. While playing, boost and cut the low midrange so you can hear how it affects your tone. Remember to play in all ranges, not just on the first few frets. Once you have an idea of the...

  • Page 17

    17 a few technical things to remember clipping = bad – keep an eye on the eq clip light. If it blinks, either reduce input gain or cut back on one or more eq ranges. As we said earlier, clipping in the preamp section is a very bad thing and is to be avoided at all times. If you find yourself running...

  • Page 18

    18 you’re done. Go play. There you have it: a quick and easy process to help you get the perfect tone from your eden amplifier. As previously mentioned, it make take a few extra minutes the first few times you go through this, especially if you take the time to experiment with all the knobs and swit...

  • Page 19

    19 using the wt1205 without speakers -this amplifier is designed to be used safely with headphones only, without the loud speaker plugged in. No harm will result from using the amplifier in this fashion. This allows the use of the unit for practice with headphones and as a preamplifier with other am...

  • Page 20

    20 learn more – if you’d like to learn more about your amplifier (or about our company and its activities), we invite you to visit our website – www.Eden- electronics.Com. There you’ll find articles to help you better understand our products and the technical stuff some people find so interesting. Y...

  • Page 21

    21 if you have problems, please call the usm customer service dept. At: 1-800-ussound (1-800-877-6863) when you hear the voice prompt, press 1 on your phone’s keypad. Please ship authorized returns for service to: eden electronics p.O. Box 338 115 2nd street montrose, minnesota 55363 email website e...