Installation & operating manual einbau- & bedienungsanleitung d u a l m o n o d i g i ta l a m p l i f i e r ea24000d manual (ed) 17.08.2004 12:08 uhr seite 1.
2 contents page 1. Design features 5 2. Connections & controls 6-7 2.1 front panel connection & controls 6-7 2.2 rear panel connections 6-7 2.3 speaker impedance & wire info 8 3. Amplifier mounting 8 4. Wire routing 9 4.1 main power wires 9 4.2 rca & remote wires 9 4.3 loudspeaker wires 9 4.4 bridge...
3 inhalt seite 1. Technischer aufbau / merkmale 15 2. AnschlÜsse & bedienungselemente 16-17 2.1. EingÄnge & funktionen am front panel 16-17 2.2 eingÄnge am rear panel 16-17 2.3 lautsprecher-impedanz & kabelinfo 18 3. Montage des verstÄrkers 19 4. Verkabelung / elektrischer anschluss 20 4.1 haupt-str...
4 congratulations! And thank you for choosing this emphaser ea24000d dual mono amplifier! To maximize the performance of this amplifier and your car audio system install, we recommend that you acquaint yourself thoroughly with all capabilities and features of this emphaser amplifier. Please read thi...
5 1. Design features ■ car audio amplifier: this emphaser dual mono amplifier allows cross-over controlled amplification of subwoofer systems ■ dash-mount remote lowpass level control: a compact „lowpass-level“ remote control unit can be mounted close to the drivers seat. This control device allows ...
6 2. Connections & controls 2.1 front panel connections & controls 1 rca inputs 1/2-ch low-level stereo rca signal input for connection with line-out of the head-unit (sub-out) 2 rca rca output to daisy chain another ea24000d amplifier 3 power led green “operation” led, signaling correct operation o...
Rem power +12v gnd power +12v gnd mono mono bridged ground 7 2.2 rear panel connections 10 “remote” input terminal terminal to connect the amplifier to the automatic (remote) turn-on / turn-off lead of the head unit 11 “+12v” power input terminal 2 x 35mm 2 direct power input terminals to connect th...
2.3 speaker impedance & wire info the heat dissipation capacity of this amplifier has been designed to cope with very low impedance lo- ads. However, emphaser laboratories recommend to stay at or above the suggested impedance ra- tings listed below: ea24000d ➡ 1 ohms for dual mono operation ea24000d...
4.1 main power wires run the positive main power cable („+12 v“) directly from the positive terminal of the car battery to the amplifier. For protection of your car audio system against electrical fire hazards, resulting from a short-circuit of the main power cable to chassis ground a main fuse hold...
4.4 bridge connection schematic remote 1 ch 2 ch main fuse 2 x 300 a battery rem mono mono ground power +12v gnd power +12v gnd bridged min. Impedance 2 Ω 10 ea24000d manual (ed) 17.08.2004 12:08 uhr seite 10
11 4.5 general connection schematic min. Impedance 1+1 Ω remote 1 ch 2 ch main fuse 2 x 300 a battery rem mono mono ground power +12v gnd power +12v gnd bridged ea24000d manual (ed) 17.08.2004 12:08 uhr seite 11.
12 5. Crossover adjustments 5.1 lowpass crossover frequency adjustment note: before you attempt to adjust the lowpass crossover frequency, you must set the subsonic high- pass filter to its lowest position (10 hz). The lowpass cut-off frequency setting depends on some variables. As a rule of thumb, ...
13 5.4 phase-shift adjustment the phase shift function of the ea24000d can not be deactivated, as it is permanently in the signal chain. The phase-shift control enables you to match the acoustical phase relations of subwoofer and the speaker system playing in the front doors. The target is, that bot...
14 herzlichen glückwunsch! Wir danken ihnen, dass sie sich zum kauf dieses ea24000d verstärkers von emphaser entschieden haben. Damit sie die wiedergabequalität und die leistungsfähigkeit ihres verstärkers voll ausschöpfen kön- nen, möchten wir sie bitten, sich eingehend mit den möglichkeiten und te...
15 1. Technischer aufbau / merkmale ■ car audio verstÄrker: dieser dual mono digitalverstärker dient zum antrieb von hochleistungs-subwoofer systemen. ■ subwooferpegelregelung Über externe kabelfernbedienung: die im fond des fahrzeuges montierbare kleine fernbedienung ermöglicht die bequeme anpassun...
16 2. AnschlÜsse & bedienungselemente 2.1 eingÄnge & funktionen am front panel 1 cinch inputs 1/2-ch cinch eingangsbuchsen 1/2-ch für den anschluss der cinch ausgänge (sub-out) des steuergerätes 2 cinch outputs ausgangsbuchse zum verbinden von weiteren ea24000d – verstärkern 3 power led grüne „power...
Rem power +12v gnd power +12v gnd mono mono bridged ground 17 2.2 eingÄnge am rear panel 10 „rem“ input terminal eingangsterminal für den anschluss des remote-kabels des amp- oder antenna-remote ausgangs des steuergerätes 11 „+12v“ power input terminal 35mm 2 direkt-eingangsterminals für den anschlu...
18 2.3 lautsprecher impedanz & kabelinfo die wärmekapazität der kühlrippen dieser endstufe wurde bei dieser verstärker-serie für niederoh- mige lasten ausgelegt. Die minimale abschlussimpedanz der ea24000d steht unten. Die angegebene minimal-impedanz darf nicht unterschritten werden! Beachten sie na...
Achtung! Entfernen sie zu ihrer eigenen sicherheit erst das pluskabel vom pluspol der batterie! Bei allen nachfolgend beschriebenen installationsschritten muss der stromkreis des kraftfahrzeugs unterbrochen sein! Erst nach abschluss aller installationsarbeiten wird über das pluskabel der stromkreis ...
20 4.1 haupt-stromkabel verlegen sie nun das pluskabel direkt von der batterie zum verstärker. Innerhalb der ersten 30 cm nach dem pluspolklemmenabgriff muss eine hauptsicherung angebracht werden (absicherung des pluskabels gegen kurzschluss auf fahrzeug-masse und dadurch resul- tierendem kabelbrand...
21 4.4 anschluss-schema gebrÜckt remote 1 ch 2 ch main fuse 2 x 300 a battery rem mono mono ground power +12v gnd power +12v gnd bridged min. Impedance 2 Ω ea24000d manual (ed) 17.08.2004 12:08 uhr seite 21.
22 4.5 generelles anschluss-schema min. Impedance 1+1 Ω remote 1 ch 2 ch main fuse 2 x 300 a battery rem mono mono ground power +12v gnd power +12v gnd bridged ea24000d manual (ed) 17.08.2004 12:08 uhr seite 22.
5.1 tiefpass trennfrequenz achtung! Drehen sie das „subsonic“ potentiometer auf 10 hz – bevor sie sich an die einstellung der tiefpass-frequenz machen. Die zu wählende trennfrequenz des tiefpasses (lpf) beim betrieb eines subwoofers sollte ungefähr im bereich zwischen 60 bis 90 hz liegen. Falls die ...
5.4 einstellung des phase-shifts der phase-shift regler ermöglicht die beeinflussung der phasenlage des angeschlossenen subwoofer systems. Mit diesem regler – und gegebenenfalls durch zusätzliches umpolen des subwoofers, ist es möglich eine perfekte akustische phaselage zwischen dem subwoofer und de...
25 6. Technical specifications ea24000d digital dual mono amplifier rated power output — dual mono mode @14.4v: 1157w x 2 @ 4 ohms ( @14.4v: 2020w x 2 @ 2 ohms ( @14.4v: 3050w x 2 @ 1 ohms ( @18.0v: 1514w x 2 @ 4 ohms ( @18.0v: 2850w x 2 @ 2 ohms ( @18.0v: 4125w x 2 @ 1 ohms ( rated power output — b...
26 ea24000d manual (ed) 17.08.2004 12:08 uhr seite 26.
7. Emphaser limited warranty dear customer please read the warranty specifications below carefully. Should your emphaser product require warranty service, please return it to the retailer from whom it was purchased or the distributor in your country. Please do not send any product to emphaser inc. U...
8. Warranty card / garantiekarte model name: digital dual mono amplifier ea24000d serial number: date of purchase: your name: your address: city: state: zip or postal code: country: limited warranty: 24 months (valid with authorized installation appr oval only) dealer’s address & stamp ❏ installed b...