Two way component systems installation & operating manual einbau- & bedienungsanleitung.
2 3 inhalt technische merkmale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 lieferumfang . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 generelle info’s . . . . . . . ....
2 3 technische merkmale tiefmitteltÖner ■ 10 cm / 13 cm / 16 .5 cm tiefmitteltöner mit euro-din korb ■ strontium-ferrit magnet ■ fiberglas membrane ■ butylgummi sicke ■ 2-lagen schwingspule auf kaptonträger ■ hinterlüftete zentrierspinne ■ vergoldete anschlussterminals ■ magnetschutz aus gummi hocht...
4 5 generelle info’s der erste schritt einer erfolgreichen installation ist, die akustisch optimalen einbauplätze aus- zuwählen . Berücksichtigen sie für die montage der tiefmitteltöner die vom hersteller des autos vorgesehenen einbauplätze, oder besorgen sie sich ein stabiles fahrzeugspezifisches d...
4 5 aufbaumontage des hochtÖners der hochtöner für aufbaumontage besteht aus zwei kunststoff adapterschalen und der eigentlichen hochtöner-systemeinheit . Die montageadapter werden durch zusammenclippen miteinander verbunden . Markieren und bohren sie drei löcher: ein loch für die durchführung des h...
6 7 anschluss der frequenzweichen die frequenzweichen können in einem vorhandenen hohlraum in der türe, an der türverkleidung selber, oder auch in den seitenteilen des fussraums (z .B . Unter dem teppich) untergebracht oder verstaut werden . Vermeiden sie orte mit hoher feuchtigkeit oder einwirkung ...
6 7 abb .: schiebeschalter für hochtonabsenkung befestigen sie nun die tiefmitteltöner in den lautsprecheröffnungen . Achten sie auf einen perfekt dichten und satten sitz des tiefmitteltöners . Luftdichter sitz ist für eine gute bass- und kickbasswie- dergabe der systeme absolut unerlässlich . Wenn ...
8 9 inbetriebnahme das komponentensystem sollte zum erreichen der vollen klangqualität einige zeit einspielen, es erreicht erst nach etwa 20 bis 50 stunden spielzeit bei mittlerem pegel die volle klangqualität . Während dieses einspielens erreichen die aufhängungsteile am lautsprecher ihr mechanisch...
8 9 ecp210-s6 ecp213-s6 ecp216-s6 nenndurchmesser 4" (10 cm) 5 ¼" (13 cm) 6 ½" (16 .5 cm) system 2-weg 2-weg 2-weg nennbelastbarkeit 120 wrms 140 wrms 180 wrms flankensteilheit (tm/ht) 12/12 db/oct . 12/12 db/oct . 12/12 db/oct . Trennfrequenz 4000 hz 4000 hz 4000 hz nennimpedanz 4 ohms 4 ohms 4 ohm...
10 11 congratulations! On your purchase of the emphaser ecp-s6 2-way component system . If you plan on installing the ecp-s6 component system by yourself, please read the following instructions carefully before you attempt the installation . For any further information about this product, please con...
10 11 set content unpack the loudspeakers, crossovers and accessories and check if all parts are contained and undamaged, as listed below: • 2 mid/woofers ecp210-s6/ecp213-s6/ecp216-s6 • 2 tweeters ecp-s6 • 2 crossovers ecp210-s6/ecp213-s6/ecp216-s6 • 2 mid/woofer grilles • 4 tweeter mounting adapto...
12 13 general info’s the first step of a successful install is to choose the best mounting locations for the tweeters and mid/woofers . Usually, cars come with factory speaker openings for mid/woofers, and the ecp-s6 sets are designed to fit a great variety of euro-din bolt-hole patterns and cutouts...
12 13 flat surface mounting disassemble the angled surface mount adaptor . Mark and drill holes where you want to fix the tweeters . You can use the base cap directly as a template . Three holes need to be drilled, one main hole for the cable routing and two small pilot holes for fixing the base to ...
14 15 mid/woofer mounting remove the factory grilles of the front door and remove – if applicable – the factory installed full range speakers or mid/woofers . Depending on the car brand and type, it is sometimes unavoidable to remove the complete doorpanels to gain full access to the speaker opening...
14 15 slide switch for tweeter attenuation when you tighten up the screws to mount the mid/woofers in place, be sure to check for an airtight seal and good fit of the basket rim to the mounting surface . You can now re-install the factory plastic grilles or the complete door panels . If you have cho...
16 17 putting into service allow your component system to break in . During the first 20 to 50 hours of playback at medium listening levels, the mechanical suspension parts of your component system will have reached their equilibrium . In the meantime, listen for distorted sounds or mechanical noise...
16 17 ecp210-s6 ecp213-s6 ecp216-s6 nominal size 4" (10 cm) 5 ¼" (13 cm) 6 ½" (16 .5 cm) configuration/system 2-way 2-way 2-way nominal power handling 120 wrms 140 wrms 180 wrms crossover slopes (mw/tw) 12/12 db/oct . 12/12 db/oct . 12/12 db/oct . Crossover frequency 4000 hz 4000 hz 4000 hz nominal ...
18 19 warranty conditions keep the original packing and the sales receipt for warranty purposes and read the warranty limi- tations further down below . Emphaser inc ., wyoming, michigan usa warrants this ecp-s6 component speaker system and it’s parts, to be free of defects in materials and workmans...
18 19 warranty card / garantiekarte type of set: ❏ ecp210-s6 ❏ ecp213-s6 ❏ ecp216-s6 date of purchase: your name: your address: city: state: zip or postal code: country: your phone number: limited warranty: 24 months (valid with authorized installation approval only) dealer’s address & stamp ❏ insta...
Emphaser inc., wyoming, michigan, u.S.A..