Empire DV-25-2SG Installation instructions and owner's manual

Manual is about: DIRECT VENT WALL FURNACE

Summary of DV-25-2SG

  • Page 1

    R-2070 page 1 direct vent wall furnace models dv-25-2sg dv-35-2sg effective date november, 2000 installation instructions and owner's manual warning: if the information in this manual is not followed exactly, a fire or explosion may result causing property damage, personal injury or loss of life. — ...

  • Page 2

    R-2070 page 2 installation in residential garages gas utilization equipment in residential garages shall be installed so that all burners and burner ignition devices are located not less than 18" (457mm) above the floor. Such equipment shall be located, or protected, so it is not subject to physical...

  • Page 3

    R-2070 page 3 some people cannot smell well. Some people cannot smell the odor of the chemical stench put into the gas. You must find out if you can smell the odorant in propane. Smoking can decrease your ability to smell. Being around an odor for a time can affect your sensitivity or ability to det...

  • Page 4

    R-2070 page 4 location of furnace pick a location on an outside wall with a clear space of 28" (711mm) high by 49" (124cm) wide in the room. Clearances 1. In selecting a location for installation, it is necessary to provide adequate accessibility clearances for servicing and proper installation. 2. ...

  • Page 5

    R-2070 page 5 1. Attach 6" (152mm) diameter air inlet tube onto the collar of air drop assembly. Be sure 6" (152mm) diameter air inlet tube is placed as far as possible onto the collar of the air drop assembly. Mark the 6" (152mm) diameter air inlet tube 1/2" (13mm) beyond the outside wall. Remove 6...

  • Page 6

    R-2070 page 6 gas supply check all local codes for requirements, especially for the size and type of gas supply line required. On natural gas lines less than 15' (4.58m) long, use 1/2" (13mm) pipe; on longer runs, use 3/4" (19mm) iron pipe or equal. On lp gas lines please consult lp gas supplier. In...

  • Page 7

    R-2070 page 7 figure 7 thermostat location millivolt wall thermostats are specially designed for use on self-generating systems. They should never be used on line or low voltage a.C. Circuits. Interior wall — the thermostat should be installed on an inside wall away from the furnace but in the same ...

  • Page 8: Lighting Instructions

    R-2070 page 8 4. Push in gas control knob slightly and turn clock- wise to "off." do not force. 5. Replace casing front assembly. 8. Find pilot - follow metal tube from gas control. The pilot is behind the pilot access cover. 9. Turn knob on gas control counterclockwise to "pilot." 10. Push in contr...

  • Page 9

    R-2070 page 9 service and maintenance suggestions call serviceman symptoms -possible causes and corrections 1. Lit match goes out as it enters lighter port . A. Certain wind conditions will blow out match. Ignite match, and as it flares, thrust match through opening. B. Open nearby door or window an...

  • Page 10

    R-2070 page 10 how to order repair parts ... Parts can be ordered only through your service person or dealer. For best results, the service person or dealer should order parts through the distributor. Parts can be shipped directly to the service person/dealer. All parts listed in the parts list have...

  • Page 11

    R-2070 page 11 optional blower drb-1 vented room heaters rh-25-(1, 2, 4) and rh-35-(1, 2, 4) direct vent wall furnaces dv-25-(1, 2)sg and dv-35-(1, 2)sg installing optional drb-1 blower 1. For rh-25-(1, 2, 4) and rh-35-(1, 2, 4), remove casing front. 1. For dv-25-(1, 2)sg and dv-35-(1, 2)sg, remove ...

  • Page 12

    R-2070 page 12 cleaning the blower wheel will collect lint and could require cleaning once a year. If the air output decreases or the noise level increases, it indicates a dirty wheel. Complete removal of the wheel and scrubbing it with a brush under flowing water is recommended. Oiling the blower m...