- DL manuals
- FAAC
- Gate Opener
- 746 ER CAT
- Instruction Manual
FAAC 746 ER CAT Instruction Manual
Summary of 746 ER CAT
Page 1
Carta riciclata 100% per la natura for nature recycled paper 100% ist umweltfreundlich 100% altpapier para la naturaleza 100% papel reciclado papier recyclÈ 100% pour la nature voor de natuur 100% kringlooppapier 746er & 780d 746er & 780d.
Page 2
18 1) attention! To ensure the safety of people, it is important that you read all the following instructions. Incorrect installation or incorrect use of the product could cause serious harm to people. 2) carefully read the instructions before beginning to install the product. 3) do not leave packin...
Page 3
19 model 746 power supply (vac +6% -10% 50-60hz) 230 absorbed power (w) 300 reduction ratio 1 : 30 type of pinion z20 - z16 rack module 4 - step 12.566 max. Thrust (dan) 50 (z20) - 62,5 (z16) max. Torque (nm) 20 winding thermal protection (°c) 120 use frequency 70% (see graph) oil quantity (l) 1,8 t...
Page 4
20 fig. 4 fig. 5 fig. 6 fig. 7 fig. 2 fig. 3 2. Dimensions 3. Electric equipment (standard system) to make the connections efficiently, allow the cables to project by about 40 cm from the hole (figs.5-6 ref. ) of the foundation plate. 4. Installation of the automated system 4.1. Preliminary checks t...
Page 5
21 a b fig. 8 fig. 12 fig. 10 fig. 11 fig. 9 fig. 13 5) secure the gearmotor to the foundation plate, tightening the nuts as in fig.12. 6) prepare the operator for manual operating mode as described in chapter 8. 4.4. Installing the rack 4.4.1. Steel rack to weld (fig.13) 1) place the three threaded...
Page 6
22 fig. 15 fig. 16 fig. 19 fig. 21 fig. 20 notes on rack installation • make sure that, during the gate travel, all the rack elements do not exit the pinion. • do not, on any account, weld the rack elements either to the spacers or to each other. • when the rack has been installed, to ensure it mesh...
Page 7
23 – + dl led f1 j1 j2 led j5 f j7 f2 j8 j6 fig. 22 dl signalling and programming display led inputs status control led j1 low voltage terminal board j2 connector for decoder/minidec/rp receiver j5 connector for motor starting capacitor j6 motor and flashing lamp connection terminal board j7 230 vac...
Page 8
24 s a f e + + o p e n b o p e n a o p c l j1 j 5 blue s a f e + + o p e n b a o p e n o p c l s a f e + + o p e n b a o p e n o p c l s a f e + + o p e n b a o p e n o p c l fig. 23 fig. 24 fig. 25 fig. 26 fig. 27 fig. 28 5.4.1. Connection of photocells and safety devices before connecting the safe...
Page 9
25 s a f e + + o p e n b a o p e n o p c l rx op tx op s a f e + + o p e n b a o p e n o p c l rx op/cl tx op/cl rx op tx op s a f e + + o p e n b a o p e n o p c l s a f e + + o p e n b a o p e n o p c l s a f e + + o p e n b a o p e n o p c l fig. 30 fig. 31 fig. 33 fig. 32 fig. 29 connection of a...
Page 10
26 rx op/cl tx op/cl s a f e + + o p e n b a o p e n o p c l fig. 34 fig. 35 5.4.2. J7 terminal board - power supply (fig. 23) power supply (terminals pe-n-l): pe: earth connection n : power supply ( neutral ) l : power supply ( line ) nb.: for correct operation, the board must be connected to the e...
Page 11
27 minidec plus rp f - + f fig. 37 fig. 36 fig. 38 fig. 39 tx -fsw - negative for power supply to photocell transmitters (terminal 11) if you use this terminal for connecting the negative for supplying power to the photocell transmitters, you may, if necessary, also use the fail safe function (see a...
Page 12
28 f + + force: adjusts motor thrust. = minimum force = maximum force opening direction: indicates the gate opening movement and makes it possible not to change the motor connections on the terminal board. = rightward opening movement = leftward opening movement status of automated system: exit from...
Page 13
29 display function default display function default opening photocells logic: select the tripping mode of the opening photocells. They operate for the opening movement only: they stop the movement and restart it when they are released, or they reverse it immediately. = reverse immediately to closin...
Page 14
30 fc2 fc1 fig. 40 fig. 42 6.2. Definition of opening direction and operation of limit-switch leds power up the system and set the opening direction on the board (see par. 5.5.1). If opening direction is rightward ( ): opening limit-switch led = f c 1 closing limit-switch led = f c 2 if opening dire...
Page 15
31 m fig. 46 fig. 45 fig. 44 fig. 43 7. Final operations at end of installation, apply the danger sticker on the top of the cover (fig. 45). 6.7. Check of stop points take care over the setting of the post-limit-switch deceleration and braking: if deceleration is too long and braking is insufficient...
Page 16
32 fig. 50 fig. 49 fig. 48 fig. 52 9. Restoring normal operation to prevent an involuntary pulse from activating the gate during the manoeuvre, cut power to the system before re-locking the operator. 1) re-close the release lever. 2) turn the key anti-clockwise 3) remove the key and close the lock p...
Page 17
33 " p a" ci g o l s e s l u p s u t at s e t a ga - n e p ob - n e p op o t ss e ci v e d y t e f a s g ni n e p os e ci v e d y t e f a s g ni s o l ce ci v e d y t e f a s l c / p oe ci v e d y t e f a s e g d e d e s o l c s es ol c d n a f a el e ht s n e p o e mi t es u a p r et f a ti l ai tr...
Page 18
34 (1) if maintained, it prolongs the pause until disabled by the command (timer function) (3) during the partial opening cycle, an open a pulse causes total opening. (2) if a new pulse occurs within 2 seconds after reversing, it immediately stops operation. Nb.: effects on other active pulse inputs...
Page 19
User’s guide automated system 746 read the instructions carefully before using the product and keep them for future consultation. General safety regulations if installed and used correctly, the 746 automated system will ensure a high degree of safety. Some simple rules regarding behaviour will avoid...