Faber CRISTAL HC Installation Instructions Manual

Other manuals for CRISTAL HC: Installation Instructions Manual
Manual is about: Slideout Rangehood

Summary of CRISTAL HC

  • Page 1

    Version 10/05 - page 1 read these instructions before you start installing this rangehood warning: - to reduce the risk of a range top grease fire: a) never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medi...

  • Page 2: Warning

    Version 10/05 - page 2 venting requirements determine which venting method is best for your application. Ductwork can extend either through the wall or the roof. The length of the ductwork and the number of elbows should be kept to a minimum to provide efficient performance. The size of the ductwork ...

  • Page 3: Avertissement

    Version 10/05 - page 3 rÈglements d'Évacuation confirmer la sortie d'évacuation - soit par le mur, soit par le toit. Utilisez une longueur de tuyauterie minimale avec les moindres de coudes pour la plus grande efficacité. Le diamètre de tuyauterie doit être uniforme. N'installez jamais 2 coudes ensemb...

  • Page 4

    Version 10/05 - page 4 cut-out cristal hc dimensions front trim options the cristal hc comes with a white front strip installed. Optional black and brushed aluminum strips are included in the box. For a custom front strip, a local cabinet shop can make a strip to match your cabinets. Custom front tr...

  • Page 5

    Version 10/05 - page 5 9.0 feet 10.0 feet 0.0 feet 19.0 feet tools needed for installation • saber saw or jig saw • drill • 1 1/4" wood drill bit • pliers • phillips screwdriver • wire stripper or utility knife • metal snips • measuring tape or ruler • level • pencil • caulking gun • duct tape parts...

  • Page 6

    Version 10/05 - page 6 install the rangehood 1. Remove the rangehood from the carton and place on a flat surface. Cover the surface to prevent accidental damage. Remove all parts including the backdraft damper, plastic grille and literature package before discarding the carton. Remove the grease filte...

  • Page 7

    Version 10/05 - page 7 warranty & service all faber products are warranteed against any defect in ma- terials or workmanship for the original purchaser for a period of 1 year from the date of original purchase. This warranty covers labor and replacement parts. The warranty does not cover consumable ...

  • Page 8

    Version 10/05 - page 8 wiring diagram / diagramme de filage • this rangehood uses flourescent lamp type f33-15w-t8 and starter type s2. 177 035 newcristal • cette hotte utilise une ampoule fluorescente, type f33-15w-t8 et un déclencheur, type s2..

  • Page 9

    Version 10/05 - page 9 cut-out dimensions de la hotte options de la bande frontale la bande frontale instaleé sur la cristal hc est blanche. Une bande noire et une bande aluminum brossé sont incluses dans la boîte afin d'armoniser selon notre décor. Pour des bandes sur mesure, un marchand dʼarmoires ...

  • Page 10

    Version 10/05 - page 10 outils nÉcessaires À lʼinstallation • scie sauteuse ou à découper • perceuse • mèche à bois 1 1/4 po • pinces • tournevis phillips • dénude fil ou couteau tout usage • pince coupante à fil métallique • ruban à mesurer ou règle • niveau • crayon • outil à calfeutrage • ruban à c...

  • Page 11

    Version 10/05 - page 11 installation de la hotte 1. Retirer lʼappareil de la boîte et le déposer sur une surface plate pour lʼassemblage. Couvrir la surface pour éviter tout dommage. Retirer toutes les pièces incluant les le registre à clapet, la grille en plastique, et nécessaire de documentation a...

  • Page 12

    Version 10/05 - page 12 garantie et service faber garantit à lʼutilisateur-acheteur dʼorigine que les produits faber vendus neufs par nous sont sans vice de matériel et de main-dʼoeuvre dʼorigine pour une période dʼun an à partir de la date dʼachat. La garantie couvre la main-dʼoeuvre et les pièces ...