Faber Dama Isola Installation Instructions Manual

Manual is about: Island Mount Canopy Rangehood

Summary of Dama Isola

  • Page 1

    Version 08/10 - page 1 dama isola island mount canopy rangehood read these instructions before you start installing this rangehood warning: - to reduce the risk of a range top grease fire: a) never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that ma...

  • Page 2: Warning

    Version 08/10 - page 2 venting requirements determine which venting method is best for your application. Ductwork can extend either through the wall or the roof. The length of the ductwork and the number of elbows should be kept to a minimum to provide efficient performance. The size of the ductwork...

  • Page 3: Avertissement

    Version 08/10 - page 3 rÈglements d'Évacuation confirmer la sortie d'évacuation - soit par le mur, soit par le toit. Utilisez une longueur de tuyauterie minimale avec les moindres de coudes pour la plus grande efficacité. Le diamètre de tuyauterie doit être uniforme. N'installez jamais 2 coudes ense...

  • Page 4

    Version 08/10 - page 4 tools needed for installation • saber saw or jig saw • drill • 1 1/4" wood drill bit • pliers • phillips screwdriver • flat blade screwdriver • wire stripper or utility knife • metal snips • measuring tape or ruler • level • pencil • caulking gun • duct tape parts supplied for...

  • Page 5: Warning

    Version 08/10 - page 5 upper chimney cover lower chimney cover canopy cabinet base x = distance from hood to cooktop (varies depending on installation) min - 24”, suggested max - 30” also consult cooktop manufacturer's recommendation 3 3/8” min 15 3/8” max 23 5/8” 4 3/4” 36” figure 4 ducted dimensio...

  • Page 6: Warning

    Version 08/10 - page 6 plan the installation this rangehood can be installed as either ducted or ductless. When installed ductless, the rangehood vents out of grates on either side of the lower chimney. Ductless installations require a ductless conversion kit, available from your dealer. Warning! Be...

  • Page 7

    Version 08/10 - page 7 . Attach the support 4. Determine and make necessary cuts for the ductwork. The duct opening is shown on the mounting template (l in figure 7). Install ductwork before mounting the support. Figure 9 figure 7 ductless installations require a ductless conversion kit whose compon...

  • Page 8: Warning

    Version 08/10 - page 8 for ductless installations, install the charcoal filter (f in figure 10) behind the center grease filter opening by inserting and locking into place. See figure 14 warning due to the size and weight of this rangehood, three people are required to install the canopy. Two people...

  • Page 9

    Version 08/10 - page 9 figure 16 figure 17 use and care information this rangehood system is designed to remove smoke, cooking vapors and odors from the cooktop area. Rangehood control panel the control panel is located on the front edge of the rangehood canopy. The position and function of each con...

  • Page 10

    Version 08/10 - page 10 faber warranty & service (save for your records) all faber products are warranteed against any defect in materials or workmanship for the original purchaser for a period of 1 year from the date of original purchase. This warranty covers labor and replacement parts. To obtain ...

  • Page 11

    Version 08/10 - page 11 outils nÉcessaires À l’installation • scie sauteuse ou à découper • perceuse • mèche à bois 1 1/4 po • pinces • tournevis phillips • tournevis à lame plate • dénude fil ou couteau tout usage • pince coupante à fil métallique • ruban à mesurer ou règle • niveau • crayon • outi...

  • Page 12: Avertissement

    Version 08/10 - page 12 couvercle cheminée supérieure couvercle cheminée inférieure hotte cabinet base x = distance entre la hotte et la table de cuisson min - 24 po, suggested max - 30 po 3 3/8 po min 15 3/8 po max 23 5/8 po 4 3/4 po 36 po figure 4 avec conduit x min & max hauteurs de plafond x = 3...

  • Page 13: Avertissement

    Version 08/10 - page 13 plan de l’installation cette hotte peut être installée avec ou sans conduit. Lorsque installé sans conduit, la ventilation s'effective par des grilles fournies avec le kit pour conversion du conduit.Les installations sans conduit requièrent un nécessaire approprié disponible ...

  • Page 14

    Version 08/10 - page 14 installation du support 6. Déterminer l’emplacement approprié pour le câble d’alimentation, tel qu’il est indiqué sur le gabarit. Utiliser un foret de 1 1/4 po pour faire un trou et y passer le câble d’alimentation. Utiliser de la pâte à calfeutrer pour sceller tout autour du...

  • Page 15: Avertissement

    Version 08/10 - page 15 pour installations sans conduit, installer le filtre au charbon (f de la figure 10). Voyez figure 14 avertissement À cause de la dimension et du poids de cette hotte, il faut avoir trois personnes pour l'installation de la hotte. Deux personnes doit tenir la hotte pendant que...

  • Page 16

    Version 08/10 - page 16 figure 17 bouton marche-arrêt de la lumière (l) interrupteur marche-arrêt pour la lumière. Pousser le bouton pour mettre en circuit (on), le pousser encore pour mettre hors circuit (off). Led allumage moteur ( i ) illuminer pour indiquer la moteur en circuit. Bouton marche-ar...

  • Page 17

    Version 08/10 - page 17 faber garantie et service ( Économiser pour vos enregistrements ) faber garantit à l’utilisateur-acheteur d’origine que les produits faber vendus neufs par nous sont sans vice de matériel et de main-d’oeuvre d’origine pour une période d’un an à partir de la date d’achat. La g...