Faber DIAMANTE Installation Instructions Manual - Warning

Version 12/04 - Page 4

For best results, use no more than three 90°  elbows.  Make sure that 

there is a minimum of 24" of straight duct between elbows if more than 

one is used.  Do not install two elbows together.  If you must elbow right 

away, do it as far away from the hood's exhaust opening as possible.

9 Feet Straight Duct

2 - 90˚ Elbows

Wall Cap

Total System

9.0 feet

10.0 feet

0.0 feet

19.0 feet

FIGURE  3

3.0 feet

5.0 feet

12.0 feet

0.0 feet

45˚ Elbow

90˚ Elbow

90˚ Flat Elbow

Wall Cap

FIGURE  2

PLAN  THE  INSTALLATION

This rangehood can be installed as either ducted or ductless.  The blower 

can be vented through the wall or ceiling.  To vent through a wall, a 90° elbow 

is used.  When installed ductless, the rangehood vents out of grates on the 

sides of the chimney.  Ductless installations require a Ductless Conversion 

Kit, available from your dealer.

WARNING!  BEFORE MAKING ANY CUTS OR HOLES FOR INSTALLATION, 

DETERMINE WHICH VENTING METHOD WILL BE USED AND CAREFULLY 

CALCULATE ALL MEASUREMENTS.

TOOLS NEEDED FOR INSTALLATION

• Saber Saw or Jig Saw

• Drill

• 1 1/4" Wood Drill Bit

• Scissors

• Pliers

• Phillips Screwdriver

• Flat Blade Screwdriver

• Wire Stripper or Utility Knife

• Metal Snips

• Measuring Tape or Ruler

• Level

• Pencil

• Caulking Gun

• Duct Tape

PARTS SUPPLIED FOR INSTALLATION

• 1 Hardware Package

• 1 Literature Package

PARTS NEEDED FOR INSTALLATION

• 2 Conduit Connectors

• Power Supply Cable

• 1 Wall or Roof Cap

• All Metal Ductwork

OPTIONAL ACCESSORIES AVAILABLE

• Backsplash

Choose either 24" or 30" high, mounts to the wall 

beneath the rangehood for a coordinated look

30" X 24" high part # 6098835 - Stainless

36" X 24" high part # 6098815 - Stainless

30" X 30" high part # 620000095 - Stainless

36" X 30" high part # 620000096- Stainless

• High Ceiling Chimney Kit

One 40" upper chimney to replace 16 

1/8"

 upper 

chimney that came with hood

part # 620000071 - Stainless

• *Ductless Conversion Kit

For non-vented installations only

* it is highly recommended that professional style 

cooking always be vented to the outside

part #620000072 - Stainless

• Replacement Charcoal Filter

For non-vented installations only,

replace charcoal filter as needed

part # 620000041

   WARNING

Because of the weight and size of the rangehood 

canopy, two or more people are needed to move 

and safely install the rangehood canopy.

Failure to properly lift rangehood could result in 

damage to the product or personal injury.

PERSONAL INJURY HAZARD

CALCULATE  THE  DUCTRUN  LENGTH

The ductrun should not exceed 35 equivalent feet if ducted with the required 

minimum of 6" round duct.  Calculate the length of the ductwork by adding 

the equivalent feet in FIGURE 2 for each piece of duct in the system.  An 

example is given in FIGURE 3.

RANGEHOOD  COMPONENTS

FIGURE  1

A. CANOPY SECTION

B. LOWER CHIMNEY COVER

C. UPPER CHIMNEY COVER

D. MOUNTING SCREWS

E. CHIMNEY MOUNTING

F. MOUNTING PLUGS

G. CHIMNEY SCREWS

H. DAMPER

BRACKETS

!