1. DL manuals
  2. FabiaTech
  3. Motherboard
  4. FB2631
  5. User Manual

FabiaTech FB2631 User Manual

Manual is about: 3’5 CPU Board Low Power Series

Summary of FB2631

  • Page 1

    I fabiatech corporation ipc solution website: http:// www.Fabiatech.Com email: support@fabiatech.Com pci/104 3’5 cpu board low power series fb2631 user’s manual jan 2009 version: 1.1 part number: fb2631.

  • Page 2

    Ii copyright copyright © 2008 fabiatech corporation, the content of this publication may not be reproduced in any part or as a whole, transcribed, stored in a retrieval system, translated into any language, or transcribed in any form or by any means, electronic, mechanical, and magnetic… or otherwis...

  • Page 3: Table of Contents

    Iii table of contents fb2631 user’s manual ...........................................................................................................I chapter 1 introducing the fb2631 system................................................................................ 1 overview.....................

  • Page 4

    Iv cn2, j1/j5: lcd connector & power connector .......................................23 chapter 4 bios setup ............................................................................................................... 25 overview......................................................................

  • Page 5

    V watchdog timer...................................................................................................................60 watchdog timer setting ..................................................................................61 watchdog timer enabled ......................................

  • Page 6

    Vi.

  • Page 7

    Fabiatech corporation 1 chapter 1 introducing the fb2631 system overview the fb2631 is a via eden (v4) ™ low power processor, all in one, 3’5 embedded cpu board. This user’s manual provides information on the physical features, installation, and bios setup of the fb2631. Built to unleash the total p...

  • Page 8

    Fabiatech corporation 2 layout j3 j8 sata2 sata1 cn15 u1 j1 j7 jp4 cn9 j5 cn13 cn14 cn5 cn6 com1 sw1 db1 jp5 j2 cn7 bat1 cn2 u2 j6 jp8 cn10 j4 jp9 jp10 bz1 d7 d21 cn8 cn1 1 1 39 41 40 42 199.

  • Page 9

    Fabiatech corporation 3 specifications via eden (v4) 1ghz and 128kb or above l2 cache inside the cpus. Supporting one 200 pin so-dimm socket for up to 1gb ddr2-400/533 ram. Two realtek 8110sc chipset 10m/100/1000m ethernet with rj-45 ports. Cx700m supports crt /lvds/tv interface use uma vram up to 1...

  • Page 10

    Fabiatech corporation 4 packing list upon receiving the package, verify the following things. Should any of the mentioned happens, contact us for immediate service. • unpack and inspect the fb2631 package for possible damage that may occur during the delivery process. • verify the accessories in the...

  • Page 11

    Fabiatech corporation 5 chapter 2 hardware installation this chapter introduces the system connectors & jumper settings, and guides you to apply them for field application. Before installation before you install the system, make sure you follow the following descriptions. 1. Before removing the boar...

  • Page 12

    Fabiatech corporation 6 hardware features the following list is for the setup of the connectors and jumpers of the fb2631. Item description cn1 ddr2 so-dimm socket (200-pin) cn2 lcd connector with lvds signals (df13-40-pin) cn5, cn6 lan#1,lan#2 -lan connector (rj45) cn7 ide 2 hard disk connector (id...

  • Page 13

    Fabiatech corporation 7 cn5, cn6: rj45 lan connector with led indicators the rj45 connector with 2 led’s for lan. The left side led (orange) indicates data which is being accessed and the right side led (green) indicates on-line status. (on indicates on-line and off indicates off-line). The followin...

  • Page 14

    Fabiatech corporation 8 j7: keyboard/mouse connector j7 is a 6-pin 2.0mm jst connector, use the included kb/ms adapter cables you can attach standard ps/2 type keyboard and mouse. J3 j8 sata2 sata1 cn15 u1 j1 j7 jp4 cn9 j5 cn13 cn14 cn5 cn6 com1 sw1 db1 jp5 j2 cn7 bat1 cn2 u2 j6 jp8 cn10 j4 jp9 jp10...

  • Page 15

    Fabiatech corporation 9 j2: audio connector j2 is a 12-pin 2.0mm idc connector with hd codec signals for audio. Use the included audio cable and fb4706x adapter board for your audio applications. J3 j8 sata2 sata1 cn15 u1 j1 j7 jp4 cn9 j5 cn13 cn14 cn5 cn6 com1 sw1 db1 jp5 j2 cn7 bat1 cn2 u2 j6 jp8 ...

  • Page 16

    Fabiatech corporation 10 cn13, cn14: usb connector the fb2631 supports a four port usb connector. Any usb device can be attached to usb ports with plug-and-play supported. The cn13 and cn14 port is usb # 1/2 and the j4 is usb # 3/4 is j4 use the usb adapter cable or fb4706x board, you can attach up ...

  • Page 17

    Fabiatech corporation 11 ¾ cn10: serial port 2 the cn10 is 10-pin 2.0mm idc connectors. The included serial port adapter cables are used to transfer 10-pin 2.0mm idc into standard db-9 connector, the following tables show the signal connections of connector. The serial port 2 is designed for multipl...

  • Page 18

    Fabiatech corporation 12 cn7: ide hard disk connectors cn7 is 44-pin 2.0mm idc connectors. Use the included hard disk cables to attach up to two 2.5” hard disk drives. J3 j8 sata2 sata1 cn15 u1 j1 j7 jp4 cn9 j5 cn13 cn14 cn5 cn6 com1 sw1 db1 jp5 j2 cn7 bat1 cn2 u2 j6 jp8 cn10 j4 jp9 jp10 bz1 d7 d21 ...

  • Page 19

    Fabiatech corporation 13 sata1/sata2: serial ata hard disk connector this connector is for sata hard disk use the sata cables to attach up to two sata hard disk drives. J3 j8 sata2 sata1 cn15 u1 j1 j7 jp4 cn9 j5 cn13 cn14 cn5 cn6 com1 sw1 db1 jp5 j2 cn7 bat1 cn2 u2 j6 jp8 cn10 j4 jp9 jp10 bz1 d7 d21...

  • Page 20

    Fabiatech corporation 14 cn9: pci/104 bus connectors j3 j8 sata2 sata1 cn15 u1 j1 j7 jp4 cn9 j5 cn13 cn14 cn5 cn6 com1 sw1 db1 jp5 j2 cn7 bat1 cn2 u2 j6 jp8 cn10 j4 jp9 jp10 bz1 d7 d21 pci/104 a, b & c, d pin pin signal pin signal pin signal pin signal a1 gnd b1 - c1 + 5v d1 ad0 a2 vi/o* b2 ad2 c2 a...

  • Page 21

    Fabiatech corporation 15 cn1: so-dimm socket the cn1- dimm socket on the solder side accepts 128mb to 1gb of ddr2 400/533 ram modules cn8 cn1 1 1 39 41 40 42 199 cn8 & jp4: compact flash socket and master/slave select the compact flash socket cn8 (on the solder side) is optional and supports 3.3v co...

  • Page 22

    Fabiatech corporation 16 cn15: mini-atx power connector (10-pin 2.54mm atx connector) the connector connecting mini-atx power supply, you can connect cn15 to atx power supply, and connect j3 to a push button switch as soft power switch. J3 j8 sata2 sata1 cn15 u1 j1 j7 jp4 cn9 j5 cn13 cn14 cn5 cn6 co...

  • Page 23

    Fabiatech corporation 17 ¾ j3: pwe-sw (atx-power only) the j3 is a 2 pin connecting to pwe-sw; it’s pushing the pwe-sw button once will switch the cpu board to on and off. It’s depending on system bios (power management setup) or os setting. Pushing the power button while in the on mode for more tha...

  • Page 24

    Fabiatech corporation 18 bz1 & led indicators: onboard buzzer & power/pata/sata led’s the power, pata and sata hdd led’s have two distinctive statuses: off for inactive operation and blinking light for activity. The d21 for sata and hdd and d7 is for power status led’s. J3 j8 sata2 sata1 cn15 u1 j1 ...

  • Page 25

    Fabiatech corporation 19 chapter 3 installing crt/ lcd/video display this chapter describes the configuration and installation procedure of lcd, crt and tv-out displays. Both crt and lcd displays or tv-out and lcd may be used at the same time. However, each type of lcd requires different bios settin...

  • Page 26

    Fabiatech corporation 20 crt display the fb2631 supports a crt colored monitor. It can be connected to create a compact video solution for the industrial environment. 64mb simulated vram allows a maximum crt resolution of 1920x1200 with 24 bpp. The following table and figure illustrate the pin defin...

  • Page 27

    Fabiatech corporation 21 video-out ntsc/pal tv-out display the board supports a tv-out. It can be connected to tv monitor. Jp5: tv-out mode the jp5 pin 5, 6 is select tv-out mode + lcd simultaneously. If you system is connect the tv-out and lcd, you need set the jumper to 5, 6 close. J3 j8 sata2 sat...

  • Page 28

    Fabiatech corporation 22 lcd display the board can support 24bit lvds lcd and 48-bit dual channel lvds lcd, using the bios setting for different types of lcd pane, then set your system properly and configures bos setting for the right type of lcd panel you are using. J3 j8 sata2 sata1 cn15 u1 j1 j7 ...

  • Page 29

    Fabiatech corporation 23 cn2, j1/j5: lcd connector & power connector cn2 is a lvds lcd interface connector, and j1/j5 is the power connector for inverter board. The pin assignments are listed in the following table. ¾ jp10: select lcd voltage input the jp10 can select to 3.3v or 5v vdd1 and vdd2 pin...

  • Page 30

    Fabiatech corporation 24.

  • Page 31

    Fabiatech corporation 25 chapter 4 bios setup this chapter describes the bios setup. Overview bios are a program located on a flash memory chip on a circuit board. It is used to initialize and set up the i/o peripherals and interface cards of the system, which includes time, date, hard disk drive, t...

  • Page 32

    Fabiatech corporation 26 bios functions on the menu, you can perform the following functions 1. Main 2. Advanced ¾ cpu configuration ¾ ide configuration ¾ superio configuration ¾ hardware health configuration ¾ acpi configuration ¾ apm configuration ¾ usb configuration 3. Pcipnp 4. Boot ¾ boot setti...

  • Page 33

    Fabiatech corporation 27 6. Chipset ¾ northbridge via cx700 configuration ¾ southbridge via cx700 configuration 7. Exit ¾ save changes and exit: exit system setup after saving the changes.F10 key can be used for this operation. ¾ discard changes and exit: exit system setup without saving any changes...

  • Page 34

    Fabiatech corporation 28 main setup this section describes basic system hardware configuration, system clock setup and bios version information. If the cpu board is already installed in a working system, you will not need to select this option anymore. System memory this option is display-only which...

  • Page 35

    Fabiatech corporation 29 advanced setup select the advanced tab from the setup screen to enter the advanced bios setup screen. You can select any of the items in the left frame of the screen, such as superio configuration, to go to the sub menu for that item. You can display an advanced bios setup o...

  • Page 36

    Fabiatech corporation 30 ¾ ide configuration you can use this screen to select options for the ide configuration settings. Use the up and down keys to select an item. Use the and keys to change the value of the selected option. A description of the selected item appears on the right side of the scre...

  • Page 37

    Fabiatech corporation 31 jumpers, please refer to the hard disk’s installation descriptions and the hard disk jumper settings. You can select under the and fields. This will enable auto detection of your ide drives during boot up. This will allow you to change your hard drives (with the power off) a...

  • Page 38

    Fabiatech corporation 32 ide detect time out (sec.) set this option to stop the amibios from searching for ide devices within the specified number of seconds. Basically, this allows you to fine-tune the settings to allow for faster boot times. Adjust this setting until a suitable timing that can det...

  • Page 39

    Fabiatech corporation 33 ¾ superio chipset - configuration win627 super io chipset this section describes the function of super i/o settings. Serial port 1 address these fields select the i/o port address for each serial port. Available options: disabled, 3f8h/irq4, 3e8h/irq4, 2f8h/irq4 and 2e8h/irq...

  • Page 40

    Fabiatech corporation 34 ¾ hardware health configuration on the hardware monitor setup screen, you can monitor the system temperature, cpu voltage, and cpu fan speed….

  • Page 41

    Fabiatech corporation 35 ¾ advanced acpi settings acpi aware o/s this filed specifies allow you set this value to utilize the acpi (advanced configuration and power interface) specification. Available options: yes, and no default setting: yes general acpi configuration suspend mode this filed specif...

  • Page 42

    Fabiatech corporation 36 ami oemb table set this value to allow the acpi bios to add a pointer to an oemb table in the root system description table (rsdt) table. Available options: enable, and disable default setting: enable chipset acpi configuration apic acpi sci irq allows you to enable or disab...

  • Page 43

    Fabiatech corporation 37 power manager /apm select enabled to activate the chipset power management and apm (advanced power management) features. Available options: disable and enable default setting: enable power button mode this option specifies how the externally mounted power button on the front...

  • Page 44

    Fabiatech corporation 38 standby time out this field specifies the length of a period of system inactivity (like hard disk or video) while in full power on state. When this length of time expires, the system enters standby power state. Available options: disabled, 1 minute, 2 minute, 4 minute, and 8...

  • Page 45

    Fabiatech corporation 39 hard disk power down mode this field specifies the power conserving state that the hard disk drive enters after the specified period of hard drive inactivity has expired. Available options: disabled, standby, suspend default setting: disabled resume on rtc alarm this field s...

  • Page 46

    Fabiatech corporation 40 ¾ usb configuration you can use this screen to select options for the usb configuration. Usb 1.1 ports configuration set this value to allow the system to enable or disable the onboard usb ports. The optimal and fail-safe default setting is 4 usb ports. Available options: 2 ...

  • Page 47

    Fabiatech corporation 41 legacy usb support legacy usb support refers to the usb mouse and usb keyboard support. Normally if this option is not enabled, any attached usb mouse or usb keyboard will not become available until a usb compatible operating system is fully booted with all usb drivers loade...

  • Page 48

    Fabiatech corporation 42 pcipnp setup select the pci/pnp tab from the setup screen to enter the plug and play bios setup screen. You can display a plug and play bios setup option by highlighting it using the keys. All plug and play bios setup options are described in this section. The plug and play ...

  • Page 49

    Fabiatech corporation 43 pci latency timer this field specifies the latency timings (in pci clock) pci devices installed in the pci expansion bus. Available options: 32, 64, 96, 128, 160,192, 224, and 248 default setting: 64 palette snoop when enabled is selected, multiple vga devices operating on d...

  • Page 50

    Fabiatech corporation 44 dma channel 0 – 7 when i/o resources are controlled manually, you can assign each system dma as one of the following types, based on the type of device using the interrupt: available: specified irq is available to the used by pci/pnp devices. Reserved: specified irq is reser...

  • Page 51

    Fabiatech corporation 45 boot setup select the boot tab from the setup screen to enter the boot bios setup screen. You can select any of the items in the left frame of the screen, such as boot device priority, to go to the sub menu for that item. You can display a boot bios setup option by highlight...

  • Page 52

    Fabiatech corporation 46 ¾ boot setting configuration quick boot this field is used to activate the quick boot function of the system. When set to enabled, 1. Bios will not wait for up to 40 seconds if a ready signal is not received from the ide drive, and will not configure its drive. 2. Bios will ...

  • Page 53

    Fabiatech corporation 47 available options: on, off default setting: on ps/2 mouse support the ps/2 mouse function is optional. Before you configure this field, make sure your system board supports this feature. The setting of enabled allows the system to detect a ps/2 mouse on boot up. If detected,...

  • Page 54

    Fabiatech corporation 48 ¾ boot device use this screen to specify the order in which the system checks for the device to boot from. To access this screen, select boot device priority on the boot setup screen and press . First /second /third hard disk boot device set the boot device options to determ...

  • Page 55

    Fabiatech corporation 49 ¾ hard disk drives use this screen to view the hard disk drives in the system. To access this screen, select hard disk drives on the boot setup screen and press . ¾ cd/dvd disk drives use this screen to view the cd/dvd drives in the system. To access this screen, select cd/d...

  • Page 56

    Fabiatech corporation 50 security setup there are two security passwords: supervisor and user. Supervisor is a privileged person that can change the user password from the bios. According to the default setting, both access passwords are not set up and are only valid after you set the password from ...

  • Page 57

    Fabiatech corporation 51 5. Select system or setup. Always: a visitor who attempts to enter bios or operating system will be prompted for password. Setup: a visitor who attempts to the operating system will be prompted for user password. You can enter either user password or supervisor password. 6. ...

  • Page 58

    Fabiatech corporation 52 chipset setup this section describes the configuration of the board’s chipset features. • northbridge via cx700 configuration • southbridge via cx700 configuration.

  • Page 59

    Fabiatech corporation 53 ¾ northbridge via cx700 configuration you can use this screen to select options for the north bridge configuration. Use the up and down keys to select an item. Use the and keys to change the value of the selected option. Dram clock/timing configuration dram timing if the ins...

  • Page 60

    Fabiatech corporation 54 default setting: agp onchip vga configuration vga frame buffer size this field is share memory architecture (sma) for frame buffer memory. Sma allows system memory to be efficiently share by the host cpu and allocated depending on user preference, application requirements, a...

  • Page 61

    Fabiatech corporation 55 tv type this setting refers to the native resolution of the display being used with the system. Available options: ntsc, pal, palm, paln, palnc, pali, pald, ntsc-j default setting: ntsc v- linkagp & pci bus configuration timing p ci master 0ws write this field specifies the ...

  • Page 62

    Fabiatech corporation 56 serial ata ide controller this field specifies the select sata function as raid . Available options: ide, raid default setting: ide radi/ahci bios execute this field specifies the raid/ahci rom of the sata chip. Available options: disabled, enable default setting: disable hi...

  • Page 63

    Fabiatech corporation 57 chapter 5 driver and utility the enclosed diskette includes fb2631 vga, audio driver and lan driver. To install and configure you fb2631 system, you need to perform the following steps. Via hyperionpro driver win 2000/xp driver installs via chipset, irq routing, agp driver a...

  • Page 64

    Fabiatech corporation 58 vga drivers winxp/win2000 driver 1 to install the vga driver, insert the cd rom into the cd rom device, and enter driver>vga>cx-700m> winxp_2k>setup. If your system is not equipped with a cd rom device, copy the vga driver from the cd rom to cf. 2 execute setup.Exe file. 3 t...

  • Page 65

    Fabiatech corporation 59 lan utility & driver 1 to install the lan utility or driver, insert the cd rom into the cd rom device, and enter driver>lan>rtl8110sx>diag. If your system is not equipped with a cd rom device, copy the lan driver from the cd rom to cf. 2 execute install2kxp.Exe or install98s...

  • Page 66

    Fabiatech corporation 60 watchdog timer this section describes how to use the watchdog timer, including disabled, enabled, and trigger functions. The fb2631 is equipped with a programmable time-out period watchdog timer. You can use your own program to enable the watchdog timer. Once you have enable...

  • Page 67

    Fabiatech corporation 61 ¾ watchdog timer setting the watchdog timer is a circuit that may be used from your program software to detect system crashes or hang-ups. Led on the front side is the watchdog timer indicator. Whenever the watchdog timer is enabled, the led will blink to indicate that the t...

  • Page 68

    Fabiatech corporation 62 ¾ watchdog timer enabled to enable the watchdog timer, you have to output a byte of timer factor to the watchdog. The following is a turbo c ++ program, which demonstrates how to enable the watchdog timer and set the time-out period at 6 seconds. #include “stdio.H” #include ...

  • Page 69

    Fabiatech corporation 63 ¾ watchdog timer disabled to disable the watchdog timer, simply write a 00h to the watchdog register. #include “stdio.H” #include “wdlib.H” main( ) { initwd(equwdunits); printf (“disable watch dog”); //disable watch dog diswd(wd_time); }.

  • Page 70

    Fabiatech corporation 64 programming rs-485 the majority communicative operation of the rs-485 is in the same of the rs-232. When the rs-485 precedes the transmission, which needs control the txc signal, and the installing, steps are as follows: step 1: enable txc step 2: send out data step 3: waiti...

  • Page 71

    Fabiatech corporation 65 ¾ initialize com port step 1: initialize com port in the receiver interrupt mode, and /or transmitter interrupt mode. (all of the communication protocol buses of the rs-485 are in the same.) step 2: disable txc (transmitter control), the bit 0 of the address of offset+4 just...

  • Page 72

    Fabiatech corporation 66 ¾ receive data the rs-485’s operation of receiving data is in the same of the rs-232’s. ¾ basic language example a. Initial 86c450 uart 10 open “com1:9600,m,8,1”as #1 len=1 20 rem reset dtr 30 out &h3fc, (inp(%h3fc) and &hfa) 40 return b. Send out one character to com1 10 re...

  • Page 73

    Fabiatech corporation 67 60 rem read one character from com1: buffer 70 inpstr$=input$(1,#1) 80 return note: the example of the above program is based on com1 (i/o address 3f8h). The rs-422/rs-485 of the fb2631 uses com2. If you want to program it, please refer to the bios setup for com2 address set...

  • Page 74

    Fabiatech corporation 68.

  • Page 75

    Fabiatech corporation 69 chapter 6 technical reference this section outlines the errors that may occur when you operate the system, and also gives you the suggestions on solving the problems. Topic include: z trouble shooting for post beep & error messages z technical reference trouble shooting for ...

  • Page 76

    Fabiatech corporation 70 cmos checksum error this error informs that the cmos has corrupted. When the battery runs weak, this situation might happen. Please check the battery and change a new one when necessary. Disk boot failure when you can‘t find the boot device, insert a system disk into drive a...

  • Page 77

    Fabiatech corporation 71 memory size has changed memory has been added or removed since last boot. In eisa mode, use configuration utility to re-configure the memory configuration. In isa mode enter bios setup and enter the new memory size in the memory fields. Memory verifying error it indicates an...

  • Page 78

    Fabiatech corporation 72 technical reference ¾ physical and environmental temperature: operating 0°c ~ 60°c relative humidity 5 % to 95 % non-condensing ¾ real-time clock and non-volatile ram the fb2631 contains a real-time clock compartment that maintains the date and time in addition to storing co...

  • Page 79

    Fabiatech corporation 73 address description 12 fixed disk type byte, drive d 13 reserved 14 equipment byte 15 low base memory byte 16 high base memory byte 17 low expansion memory byte 18 high expansion memory byte 19-2d reserved 2e-2f 2-byte cmos checksum 30 low actual expansion memory byte 31 hig...

  • Page 80

    Fabiatech corporation 74 ¾ cmos ram map register description 00h -10h standard at-compatible rtc and status and status register data definitions 11h – 13h varies 14h equipment bits 7-6 number of floppy drives 00 1 drive 01 2 drives bits 5-4 monitor type 00 not cga or mda 01 40x25 cga 01 2 drives 80x...

  • Page 81

    Fabiatech corporation 75 ¾ i/o port address map each peripheral device in the system is assigned a set of i/o port addresses, which also becomes the identity of the device. There is a total of 1k-port address space available. The following table lists the i/o port addresses used on the industrial cp...

  • Page 82

    Fabiatech corporation 76 ¾ interrupt request lines (irq) there are a total of 15 irq lines available on the industrial cpu card. Peripheral devices use interrupt request lines to notify cpu for the service required. The following table shows the irq used by the devices on the industrial cpu card. Le...

  • Page 83

    Fabiatech corporation 77 ¾ dma channel map the equivalent of two 8237a dma controllers is implemented in the fb2631 board. Each controller is a four-channel dma device that will generate the memory addresses and control signals necessary to transfer information directly between a peripheral device a...

  • Page 84

    Fabiatech corporation 78 ¾ serial ports the aces (asynchronous communication elements ace1 to ace2) are used to convert parallel data to a serial format on the transmit side and convert serial data to parallel on the receiver side. The serial format, in order of transmission and reception, is a star...

  • Page 85

    Fabiatech corporation 79 bit 1: enable transmitter holding empty interrupt (etbei) bit 2: enable receiver line status interrupt (elsi) bit 3: enable modem status interrupt (edssi) bit 4: must be 0 bit 5: must be 0 bit 6: must be 0 bit 7: must be 0 interrupt identification register (iir) bit 0: “0” i...

  • Page 86

    Fabiatech corporation 80 bit 5: stick parity bit 6: set break bit 7: divisor latch access bit (dlab) modem control register (mcr) bit 0: data terminal ready (dtr) bit 1: request to send (rts) bit 2: out 1 (out 1) bit 3: out 2 (out 2) bit 4: loop bit 5: must be 0 bit 6: must be 0 bit 7: must be 0 lin...

  • Page 87

    Fabiatech corporation 81 bit 4: clear to send (cts) bit 5: data set ready (dsr) bit 6: ring indicator (ri) bit 7: received line signal detect (rsld) divisor latch (ls, ms) ls ms bit 0: bit 0 bit 8 bit 1: bit 1 bit 9 bit 2: bit 2 bit 10 bit 3: bit 3 bit 11 bit 4: bit 4 bit 12 bit 5: bit 5 bit 13 bit ...

  • Page 88

    Fabiatech corporation 82 appendix dimension a. Fb2631.

  • Page 89

    Fabiatech corporation 83 b. Fb4706.