Summary of SLiCK
Page 1
Assembly manual factorbikes.Com v1.09.
Page 2
Congratulations on the purchase of your factor product. Please review thoroughly the following instructions and only follow them for correct operation and use. Should you fail to follow the following instructions and warnings, this could result in damage of the product, damage to the bicycle and in ...
Page 3
Jumping, downhill and/or training for any such events or as a result of exposing the bicycle to, or riding the bicycle in, severe conditions or climates. Labour and/or transport charges for full or part replacement, repair, return or changeover. Accident, neglect, improper handling, abuse or wilful ...
Page 4
Assembly manual 01 necessary tools factor slick aerobar assembly 1-1 torque wrench with 3, 4, 5mm hex & torx t20 bits brt-002 bearing press from enduro bearings sand paper (120-180 grift) park tool ir-1 grease & loctite 243 (dropouts) & 641 isopropyl alcohol route the di2 seatpost cable from seattub...
Page 5
Adjust the set back and saddle angle to the desired position. Tighten the m6 saddle clamp bolt to 12nm. 1-4 place the battery holders around the di2 battery. The male shell grooves must match with the female battery groove. Slide 4 mm hex wrench through the hole under the top tube and use to guide t...
Page 6
Apply installation compound to the inside of the seat tube. Connect the di2 cable to the battery. Insert seatpost into the frame to the desired height. Secure the seatpost by tightening the m8 grubscrew to 6nm lightly grease lower headset bearing and place on fork crown race. 1-9 2-3 assembly manual...
Page 7
Lightly grease and install steerer rod and tighten until there is no bearing play but the headset still spins freely. Install stem and tighten m6x20l bolts to 10 nm check headset adjustment as bearing preload may have changed during stem installation 2-6 2-5 assembly manual 04 2-4 secure headset adj...
Page 8
Assembly manual 05 3-1 di2 cable routing overall view park tool offers an excellent internal cable routing kit (park tool ir-1) to help you easily route your cables. If you do not have access to this kit you can use a derailleur inner wire and a 5mm metal cable ferrule to route your wires..
Page 9
Route the front derailleur di2 cable through the seat tube hole to the bottom bracket exit window. Connect to the di2 junction b. Carefully insert junction b and all cables through the bottom bracket shell window. Route the di2 cable from the junction a to the junction b through the down tube (as pi...
Page 10
Install armrest plates and secure by tightening m6x16l bolts to 6 nm select the desired armrest cup position and secure by tightening m5x12l bolts to 4 nm 3-5 4-4 4-7 assembly manual 07 4-3 install armrest pads route extension shifter di2 cables through extension tower select desired base plate heig...
Page 11
4-8 4-11 assembly manual 08 4-7 route di2 cables through base bar and install brake/shift levers route extension shifter di2 cables through basebar route front brake cable into stem cable stop while carefully maneuvering the handlebar assembly onto the stem. Route front and rear brake cable housings...
Page 12
4-12 4-15 assembly manual 09 4-11 secure junction a to stem cover using cable ties as pictured route di2 cables through stem cover cable port and install into junction a secure handlebar to stem by tightening m6x25l bolts to 8 nm route rear brake cable through down tube as pictured 4-13 4-14.
Page 13
4-13 4-12 4-15 assembly manual 10 4-16 install brake wedge. Use grub screws to adjust each brake arm until the brake pad is 2-3mm from the rim. It is very important that the wedge is positioned between the rollers as pictured. Placing the wedge too high could cause the brake arms to hit the brake co...
Page 14
5-5 5-4 6-3 assembly manual 11 5-3 clean the inside of the frame bottom bracket & the bottom bracket cups with an isopropyl alcohol. Apply loctite 641 on the grooves of the both bottom bracket cups. Apply loctite 641 inside the bottom bracket shell and install the cups into the frame with brt-002 be...
Page 15
5-5 5-4 7-3 assembly manual 12 6-4 install down tube cage bridge and tighten m5 torx head bolts to 2 nm. Install cage and tighten m5 torx head bolts to 2 nm for 24 or 22 mm cranks install the included wheels mfg bbright reducers/adapters. 7-1 7-2 bottle cage.
Page 16
Rear dropout storage pack 5-5 5-4 7-3 assembly manual 13 8-1 9-1 9-2 in case of dropout replacement, apply loctite 243 on bolts threads and tighten to 1 nm. Install the rear storage pack rail to the seat tube by tightening the provided m5 torx head bolts to 2 nm. Slide the storage pack down the rail...
Page 17
40mm version low version 5-5 5-4 7-3 assembly manual 14 9-3 9-4 9-5 install the storage pack cover making sure to carefully latch each tab into their corresponding holes. Complete outlook. Snap the stem cover onto the front nutrition pack. Covers are available for both 0 and 40 mm stem options. Inst...
Page 18
Factorbikes.Com.