- DL manuals
- Fadini
- Gate Opener
- Junior 633
- Instruction Manual
Fadini Junior 633 Instruction Manual
Summary of Junior 633
Page 1
En 13241 en 12453 en 12445 gb - instructions manual pag. 17-32 te sted o k junior 633 - junior 650 230 v 17 the gate opener.
Page 2
18 general warnings for people safety gb junior 633 - junior 650 introduction this operator is designed for a specific scope of applications as indicated in this manual, including safety, control and signaling accessories as minimum required with fadini equipment. □ any applications not explicitly i...
Page 3
Gb 19 the responsible manager meccanica fadini s.N.C. Responsible manager the responsible manager meccanica fadini s.N.C. Responsible manager date: 10-01-14 date: 10-01-14 notified institute and laboratory for product certification according to dm 2004/108/ec: istituto di ricerche e collaudi m.Masin...
Page 4
20 gb a - led light, blue and amber colours, for automation status indication b - casing fixing screws c - casing d - power cord for led e - elpro 63 programmer for junior 633 and junior 650 f - capacitor 16 µf g - programmer support h - 230v input power supply terminals with removable fuse i - juni...
Page 5
21 gb pic. 4 casing opening anchor plate attention:once the two side screws have been removed, lift the casing and vertically pull it out, without tearing off the “led” card cable connector. Attention:the nut under the plate must be 47 mm from the end of the bolt pic. 5 - n°1 base plate - n°4 anchor...
Page 6: 2°
22 gb 2° 3° 17 1° ! Anchoring the junior 2 mm pic. 8 ! No 230v ! No 230v electrical power supply to the programmer pic. 9 attention:disconnect the 230v electrical power supply from the electrical system terminal board for junior power supply distinction of junior installed on the right or left the f...
Page 7
23 gb pic. 11 ! ! ! ! ! Attention: do not open and invert the single magnets inside the limit switch plastic brackets. These have already been properly installed to be identified by programmer logic note well: it is most important that the gate does not run into the gate stops in opening and closing...
Page 8
24 gb 1 2 3 4 5 6 7 8 9 10 13 14 18 19 nc 15 16 17 - + nc + - - + lp nc l2 l4 l5 l6 l7 l10 1 2 3 4 5 6 7 8 9 10 1 1 12 y x - + - + m p a h c c - + external electrical power supply 230v 50hz ±10% for longer distances of 50m over, increase the section wires terminals with fuse 5a 230 v output 230v-25w...
Page 9
25 gb general description: the elpro 63 is a pcb card with microprocessor for the command and management of the junior 633 and junior 650 sliding gate opener with programming for self-learning of the different movement phases of the gate. Power supply: 230v 50hz±10% monophase corresponding to the 20...
Page 10
26 gb electrical connections to the terminals and their functions accessory electrical connections dip-switches and led indication of their functions photocells in closing: key-switch: radio contact: warning lamp output 24v- 1w: 24v output: output 24v dc/ac for dsa control: all of the nc contacts on...
Page 11
27 gb elpro 63 flashing lamp 230v max 25w: output 230v max 25w for flashing lamp on: pre-flashing before opening off: without pre-flashing 4 on: flasher desactivated during pause in automatic operation (with dip 3= on) off: it flashes during pause in automatic operation (with dip 3= on) 8 dip-switch...
Page 12: Elpro 63
28 electrical connections to the terminals and their functions elpro 63 gb input. Photocells and safety edges in opening input. Safety edges in closing common common normally alight: whenever the safety edge is engaged, the led goes off. Safety edges the two inputs, that are fitted to control the sa...
Page 13
29 gb elpro 63 functions: description of the functions of the junior 633 and junior 650 sliding gate operators note well: any variation on the dip-switch setting, to achieve the required functions, will be performed on the subsequent command to open or close, with the exception of dip-switch no.11 t...
Page 14: 10)
30 gb 1) 2) 3) = = click 4) 5) 6) 7) 8) 9) 10) programming and self-learning of the gate run 1 st operation: unlock the release handle with the coded key and open it until it stops (beyond 90°), thus freeing the gate from the junior operator. Then push the gate at about halfway of its run. Reset loc...
Page 15
31 gb opening of the unlocking handle for the manual operation of the gate by opening the unlocking handle with the coded key, the electrical power supply is always disconnected from the system. For unlocking action and subsequent manual movement of the gate, it is necessary that the handle be opene...
Page 16
32 gb hand o ver t o the end user of the installa tion maintenance record hand over to the end user of the installation installation address: installation type: sliding gate over-head door n° 1 2 3 4 5 6 service date stamp and signature installation technician/maintainer signed for acceptance end us...
Page 17
51 - données techniques junior 633 junior 650 tension d’alimentation 230 v - 50 hz 230 v - 50 hz tension moteur 230 vac 230 vac puissance absorbée max. 400 w 510 w courant absorbé max. 2 a 2,4 a force de poussée maximale 600 n 1.000 n poids max du portail 600 kg 1.200 kg nombre de tours du moteur 1....
Page 18
Timbro dell’installatore installer’s stamp cachet de l’installateur 296 mm 55 316 316 40 170 38 210 293 140 102 62,5 95 40 170 210 148 296 148 290 160 2 Ø10,2 170 55 m10 piastra di fondazione base plate plaque de fondation via mantova, 177/a - 37053 cerea (vr) italy - ph. +39 0442 330422 - fax +39 0...