1. DL manuals
  2. Fagor
  3. Power Tool
  4. 8055 FL
  5. Operating Manual

Fagor 8055 FL Operating Manual - About The Product

Other manuals for 8055 FL: Operating Manual, Operating Manual

Summary of 8055 FL

  • Page 1

    Cnc 8055 ·tc· operating manual ref.1711 soft: v02.2x.

  • Page 2

    This product uses the following source code, subject to the terms of the gpl license. The applications busybox v0.60.2; dosfstools v2.9; linux-ftpd v0.17; ppp v2.4.0; utelnet v0.1.1. The librarygrx v2.4.4. The linux kernel v2.4.4. The linux boot ppcboot v1.1.3. If you would like to have a cd copy of...

  • Page 3: I N D E X

    Operating manual cnc 8055 cnc 8055i s oft : v02.2 x ·3· i n d e x about the product ......................................................................................................................... 7 declaration of conformity and warranty conditions .............................................

  • Page 4

    ·4· operating manual cnc 8055 cnc 8055i s oft : v02.2 x 3.4 turning cycle ................................................................................................................. 86 3.4.1 data definition (levels 1 and 2) .........................................................................

  • Page 5

    Operating manual cnc 8055 cnc 8055i s oft : v02.2 x ·5· chapter 6 saving programs 6.1 list of saved programs................................................................................................. 186 6.2 see the contents of a program............................................................

  • Page 6

    ·6· operating manual cnc 8055 cnc 8055i s oft : v02.2 x.

  • Page 7: About The Product

    Cnc 8055 cnc 8055i ·7· about the product basic characteristics of the different models. Hardware options of the 8055i cnc 8055i fl en 8055 fl 8055i fl 8055 power 8055i power pendant 8055i fl en 8055i fl 8055i power enclosure ----- 8055 fl 8055 power usb standard standard standard block processing ti...

  • Page 8

    ·8· cnc 8055 cnc 8055i ab out the p ro duct software options of the 8055 and 8055i cncs. Model gp m mc mco en t tc tco number of axes with standard software 4 4 4 4 3 2 2 2 number of axes with optional software 7 7 7 7 ----- 4 or 7 4 or 7 4 or 7 electronic threading ----- stand. Stand. Stand. Stand....

  • Page 9: Warranty Conditions

    Cnc 8055 cnc 8055i ·9· declaration of conformity and warranty conditions declaration of conformity the declaration of conformity for the cnc is available in the downloads section of fagor’s corporate website at http://www.Fagorautomation.Com. (type of file: declaration of conformity). Warranty terms...

  • Page 10

    ·10· cnc 8055 cnc 8055i d e claratio n of con fo rmi ty and w a rranty co nditio n s.

  • Page 11: Version History

    Cnc 8055 cnc 8055i ·11· version history here is a list of the features added in each software version and the manuals that describe them. The version history uses the following abbreviations: inst installation manual prg programming manual opt operating manual opt-mc operating manual for the mc opti...

  • Page 12

    ·12· cnc 8055 cnc 8055i versio n history software v01.31 october 2011 software v01.40 january 2012 software v01.60 december 2013 software v01.65 january 2015 software v02.00 february 2014 list of features manual cnc 8055 fl engraving model inst / opt/ prg list of features manual execution of m3, m4 ...

  • Page 13

    Cnc 8055 cnc 8055i ·13· versio n history software v02.03 july 2014 software v02.10 november 2014 software v02.21 july 2015 software v02.22 march 2016 list of features manual set page and symbol instructions support png and jpg/jpeg formats. Prg new values for parameters maxgear1..4 (p2..5), slimit (...

  • Page 14

    ·14· cnc 8055 cnc 8055i versio n history.

  • Page 15: Safety Conditions

    Cnc 8055 cnc 8055i ·15· safety conditions read the following safety measures in order to prevent harming people or damage to this product and those products connected to it. The unit can only be repaired by personnel authorized by fagor automation. Fagor automation shall not be held responsible of a...

  • Page 16

    ·16· cnc 8055 cnc 8055i safety conditions precautions against product damage • work environment. This unit is ready to be used in industrial environments complying with the directives and regulations effective in the european community. Fagor automation shall not be held responsible for any damage t...

  • Page 17

    Cnc 8055 cnc 8055i ·17· safety conditions protections of the unit itself (8055) • "axes" and "inputs-outputs" modules. All the digital inputs and outputs have galvanic isolation via optocouplers between the cnc circuitry and the outside. They are protected by an external fast fuse (f) of 3.15 a 250v...

  • Page 18

    ·18· cnc 8055 cnc 8055i safety conditions precautions during repairs safety symbols • symbols that may appear in the manual. Do not manipulate the inside of the unit. Only personnel authorized by fagor automation may access the interior of this unit. Do not handle the connectors with the unit connec...

  • Page 19: Returning Conditions

    Cnc 8055 cnc 8055i ·19· returning conditions when sending the central nit or the remote modules, pack them in its original package and packaging material. If you do not have the original packaging material, pack it as follows: 1. Get a cardboard box whose 3 inside dimensions are at least 15 cm (6 in...

  • Page 20

    ·20· cnc 8055 cnc 8055i re tu rn in g con d iti on s.

  • Page 21: Additional Notes

    Cnc 8055 cnc 8055i ·21· additional notes mount the cnc away from coolants, chemical products, blows, etc. Which could damage it. Before turning the unit on, verify that the ground connections have been made properly. To prevent electrical shock at the central unit of the 8055 cnc, use the proper mai...

  • Page 22

    ·22· cnc 8055 cnc 8055i addi ti onal n o tes.

  • Page 23: Fagor Documentation

    Cnc 8055 cnc 8055i ·23· fagor documentation oem manual it is directed to the machine builder or person in charge of installing and starting-up the cnc. User-m manual directed to the end user. It describes how to operate and program in m mode. User-t manual directed to the end user. It describes how ...

  • Page 24

    ·24· cnc 8055 cnc 8055i fago r d o cumentatio n.

  • Page 25: General Concepts

    Cnc 8055 cnc 8055i ·tc· o ption s oft : v02.2 x 1 ·25· general concepts 1.1 keyboard alphanumeric keyboard and command keys specific keys of the tc model select the x character. Select the a character. Select the r character. These keys may be used for: • selecting and defining the machining operati...

  • Page 26

    ·26· operating manual cnc 8055 cnc 8055i 1. General conc epts ·tc· o ption s oft : v02.2 x keyboa rd jog keys these keys may be used for: • moving the axes of the machine. • governing the spindle. • modifying the feedrate of the axes and the spindle speed. • starting and stopping the execution. C+ c...

  • Page 27

    Operating manual cnc 8055 cnc 8055i general conc epts 1. ·tc· o ption s oft : v02.2 x ·27· ge neral con c epts 1.2 general concepts it offers all the features of the t model plus those specific of the tc mode. For example, the cnc setup must be done in t mode. In tc work mode, programs p900000 throu...

  • Page 28

    ·28· operating manual cnc 8055 cnc 8055i 1. General conc epts ·tc· o ption s oft : v02.2 x ge neral con c epts programs reserved for the cnc some of the programs reserved for the cnc have the following meaning: p999998 it is a program of subroutines that the cnc uses to interpret the programs edited...

  • Page 29

    Operating manual cnc 8055 cnc 8055i general conc epts 1. ·tc· o ption s oft : v02.2 x ·29· ge neral con c epts 1.2.1 p999997 text program management on power up, the cnc copies the texts of program p999997 into the system memory. • it checks if program p999997 is in user memory, if not, it looks in ...

  • Page 30

    ·30· operating manual cnc 8055 cnc 8055i 1. General conc epts ·tc· o ption s oft : v02.2 x power-up 1.3 power-up the standard screen of the tc mode is the following: on power-up and after the keystroke sequence [shift] [reset], the cnc shows "page 0" defined by the manufacturer; if there is no "page...

  • Page 31

    Operating manual cnc 8055 cnc 8055i general conc epts 1. ·tc· o ption s oft : v02.2 x ·31· wo rki ng in t mod e with the tc keyboa rd 1.4 working in t mode with the tc keyboard the tc keyboard is designed to also be able to work in t mode. In t mode, use the alphanumeric keyboard and the keys that r...

  • Page 32

    ·32· operating manual cnc 8055 cnc 8055i 1. General conc epts ·tc· o ption s oft : v02.2 x ma nag ing the cycle star t key.

  • Page 33: Operating In Jog Mode

    Cnc 8055 cnc 8055i ·tc· o ption s oft : v02.2 x 2 ·33· operating in jog mode the standard screen of the tc mode is the following: when pressing the [two-color] key, the cnc shows the special screen of the tc mode. 15:28:42 sbk p000002 in position x z s 00044.000 -00443.331 0 reference zero x 0000.00...

  • Page 34

    ·34· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x introductio n 2.1 introduction 2.1.1 standard screen of the tc mode the standard screen of the tc mode offers the following data: 1. Clock. 2. This window may show the following data: sbk when "single bl...

  • Page 35

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·35· introductio n here are all the possible cases. 6. This window shows, in large characters, the selected tool number "t" and, in small characters, the "d" offset associated with the tool. If the tool numbe...

  • Page 36

    ·36· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x introductio n 2.1.2 description of the special screen of the tc mode the special screen of the tc mode offers the following data: 1. Clock. 2. This window may show the following data: sbk when "single bl...

  • Page 37

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·37· introductio n 6. This window shows the status of the "g" functions and the auxiliary "m" functions that are active. Likewise, it shows the value of the variables. 7. Reserved. 8. Reserved. Displaying the...

  • Page 38

    ·38· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x introductio n 2.1.3 selecting a program for simulation or execution when selecting a part-program or operation saved as part of a part-program for simulation or execution, the cnc selects that part-progr...

  • Page 39

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·39· ax is control 2.2 axis control 2.2.1 work units when accessing the tc mode, the cnc assumes the work units «mm or inches", «mm/min. Or mm/rev», «radius or diameter» etc. Selected by machine parameter. To...

  • Page 40

    ·40· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x ma ch in e re fe re n c e (h om e) se arch 2.3 machine reference (home) search home search may be done in 2 ways: • homing all the axes. • homing a single axis. Homing all the axes to home all the axes, ...

  • Page 41

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·41· zero offs et table 2.4 zero offset table it is possible to manage the zero offset table from the conversational mode (g54.... G59, g159n7 ... G159n20). This table contains the same values as that of the ...

  • Page 42

    ·42· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x jo g mo vement 2.5 jog movement when making a move in manual, both in jog and with handwheels, the moving axis appears in reverse video. • with gantry axes, only the master axis is highlighted. • with a ...

  • Page 43

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·43· jo g mo vement 2.5.3 continuous jog place the movement selector in the continuous-jog position and select at the feedrate override switch (feed) the percentage (0% to 120%) of the feedrate to be applied....

  • Page 44

    ·44· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x jo g mo vement 2.5.4 path-jog the "path jog" mode acts when the switch is in one of the continuous or incremental jog positions. This feature may be used to act upon the jog keys of an axis to move both ...

  • Page 45

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·45· jo g mo vement operation in path-jog mode the "path jog" mode is only available with the x axis keys. When pressing one of the keys associated with the x axis, the cnc behaves as follows: the rest of the...

  • Page 46

    ·46· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x jo g mo vement 2.5.5 movement with an electronic handwheel this option may be used to govern the movements of the machine using an electronic handwheel. To do that, turn the left switch to any of the han...

  • Page 47

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·47· jo g mo vement 2.5.6 feed handwheel usually, when making a part for the first time, the machine feedrate is controlled by means of the feedrate override switch. From this version on, it is also possible ...

  • Page 48

    ·48· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x jo g mo vement 2.5.7 path-handwheel the "path handwheel" mode acts when the switch is in one of the handwheel positions. With this feature, it is possible to jog two axes of the plane at the same time al...

  • Page 49

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·49· tool con tro l 2.6 tool control the standard screen of the tc mode offers the following tool data. This window displays the following information: • in large characters, the tool "t" number currently sel...

  • Page 50

    ·50· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x tool con tro l 2.6.1 tool change depending on the type of tool changer, the following options are possible: • machine with automatic tool changer. • machine with manual tool changer. In either case, the ...

  • Page 51

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·51· tool con tro l 2.6.2 variable tool change point if the manufacturer so wishes, he can let the user define the tool change point every time. Obviously, this feature depends on the type of machine and type...

  • Page 52

    ·52· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x tool cal ibratio n 2.7 tool calibration the calibration mode can have several editing levels. The second level will only be available when using a table-top probe installed on the machine. What can be do...

  • Page 53

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·53· tool cal ibratio n 2.7.1 define the tool in the tool table (level 1) when accessing this level, the cnc shows the following screen. 1. Indicating the selected work mode: "tool calibration". 2. Graphic as...

  • Page 54

    ·54· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x tool cal ibratio n defining the tool type. Define the location code of the tool. Place the cursor over the icon for tool type and press the two-color key. The available tool types are: place the cursor o...

  • Page 55

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·55· tool cal ibratio n define the rest of the data related to the tool. The right window shows the tool geometry values and the left window shows help graphics. To define one of these values, select the corr...

  • Page 56

    ·56· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x tool cal ibratio n 2.7.2 manual tool calibration with/without a probe (level 1) before measuring the tool, it must be defined in the tool table. See "2.7.1 define the tool in the tool table (level 1)" on...

  • Page 57

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·57· tool cal ibratio n tool calibration place a part of known dimensions in the spindle and define its dimensions in the left window. To measure the tool, the tool must be selected on the machine. If it is n...

  • Page 58

    ·58· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x tool cal ibratio n 2.7.3 tool calibration with a probe (level 2) this calibration level requires the purchase of the right software options purchased and the use of a table-top probe. Once the cycle has ...

  • Page 59

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·59· tool cal ibratio n defining the cycle data the following data must be defined. Not all the data will always be available; the cycle will show the necessary data according to the chosen operation. • safet...

  • Page 60

    ·60· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x tool cal ibratio n 2.7.4 probe calibration (level 3) this calibration level requires the purchase of the right software options purchased and the use of a table-top probe. This cycle may be used to calib...

  • Page 61

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·61· tool cal ibratio n 2.7.5 manual tool calibration without stopping the spindle this feature may be used to manually calibrate the tool on a conversational lathe. It may be used to calibrate tools without ...

  • Page 62

    ·62· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x live too l 2.8 live tool when a live tool has been selected, the standard screen of the tc mode offers the following information: proceed as follows to select the "s" rpm of the live tool: 1. Press the [...

  • Page 63

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·63· live too l example of a plc program to manage the live tool here is an example of the portion of the plc program that must manage the live tool: ( ) = cncrd (tool, r101, m1) assigns the number of the act...

  • Page 64

    ·64· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x sp in d le co nt rol 2.9 spindle control the standard screen of the tc mode has a window that shows the following spindle related data. Since it is possible to work with the spindle in rpm, at css or in ...

  • Page 65

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·65· sp in d le co nt rol 2.9.1 spindle in rpm the cnc displays the following information. 1. Real spindle speed in rpm. 2. Theoretical spindle speed in rpm. To select another speed, press the [s] key. The cn...

  • Page 66

    ·66· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x sp in d le co nt rol 6. Spindle gear currently selected. This value cannot be changed when using an automatic gear change. When not using an automatic tool changer, press the [s] key and then use the [ ...

  • Page 67

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·67· sp in d le co nt rol 2.9.2 spindle in constant surface speed mode in constant surface speed mode, the user sets the tangential speed that must always be kept between the tool tip and the part. Therefore,...

  • Page 68

    ·68· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x sp in d le co nt rol 5. Maximum spindle speed in rpm. To select another speed, press the [s] key twice. The cnc highlights the current value. Enter the new value and press [enter]. The cnc assumes this v...

  • Page 69

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·69· sp in d le co nt rol 2.9.3 spindle orientation when using spindle orientation (general machine parameter refeed1 (p34) other than 0), the cnc shows the following information. 1. Real spindle speed in rpm...

  • Page 70

    ·70· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x sp in d le co nt rol 7. Spindle gear currently selected. To select another gear, when not using an automatic tool changer, press the [s] key and then use the [ ] key until the current value is highlight...

  • Page 71

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·71· co ntro llin g th e exte rnal de vi ces 2.10 controlling the external devices with this cnc, it is possible to activate and deactivate, via keyboard, up to 6 external devices, for example, the coolant. T...

  • Page 72

    ·72· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x iso ma nag ement 2.11 iso management access to the mdi mode or the iso mode. The iso key may be used to access the mdi mode or the iso mode. To access the mdi mode, the cnc must be in jog mode and the is...

  • Page 73

    Operating manual cnc 8055 cnc 8055i o perating in jo g mode 2. ·tc· o ption s oft : v02.2 x ·73· iso ma nag ement generating an iso-coded program in the conversational mode of the cnc, it is possible to generate an iso-coded program from an operation (cycle) or on a part-program. See "7.5 graphic re...

  • Page 74

    ·74· operating manual cnc 8055 cnc 8055i 2. O perating in jo g mode ·tc· o ption s oft : v02.2 x iso ma nag ement.

  • Page 75: Working With Operations Or

    Cnc 8055 cnc 8055i ·tc· o ption s oft : v02.2 x 3 ·75· working with operations or cycles use the following cnc keys to select the different machining operations or cycles. User cycles the user cycle is edited like any other standard cycle of the tc mode. Once all the required data has been defined, ...

  • Page 76

    ·76· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x when operating in conversational mode, do not use global parameters 150 through 299 (both included), because the operations or cycles can modify these parameters and cause the machine to malfun...

  • Page 77

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·77· op eration ed iting mod e 3.1 operation editing mode once the operation has been selected, the cnc shows a screen like the following: 1. Name of the selected operation or work cycle. 2. Help gr...

  • Page 78

    ·78· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x op eration ed iting mod e 3.1.1 definition of spindle conditions work mode (rpm) or (css) place the cursor on the "rpm" or "css" icon. To do this, use the [css] key or the [ ] [] [] [] keys...

  • Page 79

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·79· op eration ed iting mod e 3.1.2 definition of machining conditions some operations keep the machining conditions throughout the execution (positioning cycles, drilling cycle, etc.). Other opera...

  • Page 80

    ·80· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x op eration ed iting mod e machining direction. Some cycles allow the machining direction to be selected (turning direction or facing direction). Roughing pass ( ). Finishing stock ( ). Sideways...

  • Page 81

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·81· op eration ed iting mod e 3.1.3 cycle level all the cycles have several editing levels. Each level has its own screen and the main window of the cycle indicates, with tabs, the available levels...

  • Page 82

    ·82· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x simul a ting an d executin g the o peratio n 3.2 simulating and executing the operation all the operations or cycles have 2 work modes; execution and editing. • press [esc] to switch from editi...

  • Page 83

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·83· simul a ting an d executin g the o peratio n 3.2.1 background cycle editing it is possible to edit an operation or cycle while executing a program or part (background editing). The new operatio...

  • Page 84

    ·84· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x positioning c ycle 3.3 positioning cycle level 1. The following data must be defined: • coordinates of the target point. • how the movement is to be carried out. • the type of feed; in rapid or...

  • Page 85

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·85· positioning c ycle 3.3.1 definition of data order in which the axes move. Type of feedrate. Coordinates of the target point (x, z). The coordinates are defined one by one. After placing the cur...

  • Page 86

    ·86· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x turning c ycle 3.4 turning cycle turning levels 1 and 2 level 1. The following data must be defined: • coordinates of the starting point. • coordinates of the last point. • the final diameter. ...

  • Page 87

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·87· turning c ycle turning levels 3, 4 and 5 level 3. Rectangular pocket on the cylindrical side of the part. Level 4. Circular pocket on the cylindrical side of the part. Zc plane yz plane zc plan...

  • Page 88

    ·88· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x turning c ycle level 5. Zc / yz profile pocket. Y z x fx i p dx x fx i p dx c z front view y axis "c" axis front view.

  • Page 89

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·89· turning c ycle 3.4.1 data definition (levels 1 and 2) type of turning operation. When changing the type of turning operation, the cnc changes the icon and shows the corresponding help screen. C...

  • Page 90

    ·90· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x turning c ycle type of machining to be carried out on each corner. For a rounded corner, define the rounding radius (r); for a chamfer, define the distance from the theoretical corner to the ch...

  • Page 91

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·91· turning c ycle 3.4.2 data definition (levels 3, 4 and 5) level 3: level 4: icon for selecting the zc or yz plane. Icon to select the position of the starting point. Z,c / z,y: coordinates of th...

  • Page 92

    ·92· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x turning c ycle level 5: i: penetration step (pass) when roughing: • if programmed with a positive value, the actual step (pass) will be the one closest to this value and all the passes will be ...

  • Page 93

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·93· turning c ycle 3.4.3 basic operation (levels 1 and 2) the machining steps in this cycle are as follows: 1. If the roughing operation was programmed with another tool the cnc makes a tool change...

  • Page 94

    ·94· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x turning c ycle considerations how to leave out the roughing or finishing operations. By selecting t0 as the roughing tool, the cycle does not execute the roughing operation. This means that aft...

  • Page 95

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·95· facing c ycle 3.5 facing cycle facing levels 1 and 2 level 1. The following data must be defined: • coordinates of the starting point. • coordinates of the last point. • the final diameter. • t...

  • Page 96

    ·96· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x facing c ycle level 4. Circular pocket on the face of the part. Xy plane xc plane xy plane.

  • Page 97

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·97· facing c ycle level 5. Xc / xy profile cycle. X y fx p i z dz x c fx p i z dz y axis "c" axis side view side view.

  • Page 98

    ·98· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x facing c ycle 3.5.1 data definition (levels 1 and 2) coordinates of the first point (xi, zi) and of the last point (xf, zf). The coordinates are defined one by one. After placing the cursor on ...

  • Page 99

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·99· facing c ycle 3.5.2 data definition (levels 3, 4 and 5) level 3: level 4: icon for selecting the zc or yz plane. Icon to select the position of the starting point. Z,c / z,y: coordinates of the...

  • Page 100

    ·100· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x facing c ycle level 5: i: penetration step (pass) when roughing: • if programmed with a positive value, the actual step (pass) will be the one closest to this value and all the passes will be ...

  • Page 101

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·101· facing c ycle 3.5.3 basic operation (levels 1 and 2) the machining steps in this cycle are as follows: 1. If the roughing operation was programmed with another tool the cnc makes a tool change...

  • Page 102

    ·102· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x facing c ycle considerations how to leave out the roughing or finishing operations. By selecting t0 as the roughing tool, the cycle does not execute the roughing operation. This means that aft...

  • Page 103

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·103· taper turnin g cycl e 3.6 taper turning cycle level 1. The following data must be defined: • the coordinates of the theoretical corner. • the inclination angle and the final diameter. Level 2....

  • Page 104

    ·104· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x taper turnin g cycl e 3.6.1 definition of data type of taper. When changing the type of taper turning operation, the cnc changes the icon and shows the corresponding help screen. Shape of the ...

  • Page 105

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·105· taper turnin g cycl e coordinates of the theoretical corner, of the first point (xi, zi) and of the last point (xf, zf). The coordinates are defined one by one. After placing the cursor on the...

  • Page 106

    ·106· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x taper turnin g cycl e when changing the machining direction, the cnc changes the icon and shows the corresponding help screen. Finishing stocks in x-z. Either a single residual stock may be de...

  • Page 107

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·107· taper turnin g cycl e 3.6.2 basic operation the machining steps in this cycle are as follows: 1. If the roughing operation was programmed with another tool the cnc makes a tool change, moving ...

  • Page 108

    ·108· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x taper turnin g cycl e considerations how to leave out the roughing or finishing operations. By selecting t0 as the roughing tool, the cycle does not execute the roughing operation. This means ...

  • Page 109

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·109· rounding c ycle 3.7 rounding cycle level 1. The following data must be defined: • the coordinates of the theoretical corner. • the rounding radius. Level 2. The following data must be defined:...

  • Page 110

    ·110· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x rounding c ycle 3.7.1 geometry definition type of rounding. When changing the type of rounding, the cnc changes the icon and shows the corresponding help screen. Concave and convex rounding. W...

  • Page 111

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·111· rounding c ycle work quadrant. Coordinates of the theoretical corner or coordinates of the first point (xi, zi) and of the last point (xf, zf). The coordinates are defined one by one. After pl...

  • Page 112

    ·112· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x rounding c ycle machining direction. When changing the machining direction, the cnc changes the icon and shows the corresponding help screen. Finishing stocks in x-z. Either a single residual ...

  • Page 113

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·113· rounding c ycle 3.7.2 basic operation the machining steps in this cycle are as follows: 1. If the roughing operation was programmed with another tool the cnc makes a tool change, moving to the...

  • Page 114

    ·114· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x rounding c ycle considerations how to leave out the roughing or finishing operations. By selecting t0 as the roughing tool, the cycle does not execute the roughing operation. This means that a...

  • Page 115

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·115· threading c ycle 3.8 threading cycle level 1. Longitudinal threading. The following data must be defined: • coordinates of the starting point. • z coordinate of the last point. • the thread pi...

  • Page 116

    ·116· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle level 3. Face threading. The following data must be defined: • coordinates of the starting point. • coordinates of the last point. • the thread pitch. • the distance to the en...

  • Page 117

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·117· threading c ycle level 5. Threads with several entries. Available when setting spindle machine parameter "m19type (p43)=1". The following data must be defined: • coordinates of the starting po...

  • Page 118

    ·118· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle 3.8.1 geometry definition type of tapping. When changing the type of threading, the cnc changes the icon and shows the corresponding help screen. Coordinates of the first poin...

  • Page 119

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·119· threading c ycle thread pitch (p). The thread pitch may be set along the taper of the thread or along its associated axis. In either case, parameter "p" is be used, but with a different sign. ...

  • Page 120

    ·120· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle to change one of these values, place the cursor on the corresponding data, key in the desired value and press [enter]. The value of the safety distance on x is always defined ...

  • Page 121

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·121· threading c ycle type of tool penetration. When selecting any flank type penetration or in zig-zag, the cnc will request the cutter's penetration angle ( ). For the level 1 threading cycle, t...

  • Page 122

    ·122· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle penetration increment (step) in thread repair in any type of thread repair, the "h” parameter increases the depth of the repair. Only positive "h" values are admitted. This in...

  • Page 123

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·123· threading c ycle asymmetrical cutters with two tips: in the case of asymmetrical tools, the entry angle must always be respected. The tool data cuta and nosea must be entered correctly accordi...

  • Page 124

    ·124· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle 3.8.2 standard threads at all the levels except in face threading, the diameter value may be entered so the cnc calculates the relevant pitch and depths. A field (window) may ...

  • Page 125

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·125· threading c ycle regular pitch metric thread: m (s.I.) depth in internal threads = 0.5413 x pitch depth in external threads = 0.6134 x pitch diameter step depth (mm) (mm) (inches) (mm) (inches...

  • Page 126

    ·126· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle fine pitch metric thread: m (s.I.F.) depth in internal threads = 0.5413 x pitch depth in external threads = 0.6134 x pitch diameter step depth (mm) (mm) (inches) (mm) (inches)...

  • Page 127

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·127· threading c ycle normal pitch whitworth thread: b.S.W. (w) the threads must be defined in mm or inches. For example, to define a whitworth thread with a 1/16 pitch, enter 1.5875 mm or 0.0625 i...

  • Page 128

    ·128· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle fine pitch whitworth thread: b.S.F the threads must be defined in mm or inches. For example, to define a whitworth thread with a 3/16 pitch, enter 4.7625 mm or 0.1875 inches. ...

  • Page 129

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·129· threading c ycle normal pitch unified american thread: unc (nc,uss) the threads must be defined in millimeters or inches. For example, to define an american thread with a 1/4 pitch, enter 6.35...

  • Page 130

    ·130· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle fine pitch american thread: unf (nf,sae) the threads must be defined in mm or inches. For example, to define an american thread with a 1/4 pitch, enter 6.3500 mm or 0.2500 inc...

  • Page 131

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·131· threading c ycle api compliant thread the window for standard threads includes the api standard thread; a special standard for pipes of the oil sector. Once this standard is selected, a new wi...

  • Page 132

    ·132· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle 3.8.3 basic operation. Longitudinal threading the machining steps in this cycle are as follows: 1. If the operation has been programmed with another tool, the cnc will change ...

  • Page 133

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·133· threading c ycle 3.8.4 basic operation. Taper threading the machining steps in this cycle are as follows: 1. If the operation has been programmed with another tool, the cnc will change the too...

  • Page 134

    ·134· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x threading c ycle 3.8.5 basic operation. Face threading the machining steps in this cycle are as follows: 1. If the operation has been programmed with another tool, the cnc will change the tool...

  • Page 135

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·135· threading c ycle 3.8.6 basic operation. Thread repair cycle definition define the dimensions of the thread like at the rest of the levels and the coordinates of one of the roots. With the spin...

  • Page 136

    ·136· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x groovin g cycl e 3.9 grooving cycle level 1. Grooving on the cylindrical side. The following data must be defined: • the coordinates of the first and last points. • the final diameter. • the d...

  • Page 137

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·137· groovin g cycl e the following data must be defined: • the coordinates of the first and last points. • the final diameter. • the inclination angles of the incline walls. • number of grooves an...

  • Page 138

    ·138· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x groovin g cycl e 3.9.1 calibration of the grooving tool when calibrating the grooving tool, you must properly indicate the location code for the corner that has been calibrated. Thus, the same...

  • Page 139

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·139· groovin g cycl e 3.9.2 geometry definition type of grooving. When changing the type of grooving, the cnc changes the icon and shows the corresponding help screen. Coordinates of the first poin...

  • Page 140

    ·140· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x groovin g cycl e type of machining to be carried out on each corner. These data must be defined when grooving with incline walls. The type of machining must be defined for all four corners of ...

  • Page 141

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·141· groovin g cycl e type of machining for the roughing pass. To select the type of grooving, place the cursor over the desired icon and press the two- color key. Selection of the starting point o...

  • Page 142

    ·142· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x groovin g cycl e type of machining for the finishing pass. Groove repetition. The "number of grooves" and "offset" data may be used to repeat a groove several times along the z axis in cylindr...

  • Page 143

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·143· groovin g cycl e 3.9.3 basic operation. Grooving the machining steps in this cycle are as follows: 1. If the operation has been programmed with another tool, the cnc will change the tool and w...

  • Page 144

    ·144· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x groovin g cycl e considerations how to leave out the roughing or finishing operations. By selecting t0 as the roughing tool, the cycle does not execute the roughing operation. This means that ...

  • Page 145

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·145· groovin g cycl e 3.9.4 basic operation. Cut off the machining steps in this cycle are as follows: 1. If the operation has been programmed with another tool, the cnc will change the tool and wi...

  • Page 146

    ·146· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x drill ing an d ta ppin g cycl es 3.10 drilling and tapping cycles • drilling cycle. • multiple drilling cycle. • tapping cycle. • multiple threading cycle. • multiple slot milling cycle. The d...

  • Page 147

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·147· drill ing an d ta ppin g cycl es level 3. Multiple drilling cycle. Multiple drilling can be done on the cylindrical side of the part or on its face. The following data must be defined: • the c...

  • Page 148

    ·148· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x drill ing an d ta ppin g cycl es 3.10.1 geometry definition machining on the face or side of the part. When changing the type of machining, the cnc changes the icon and shows the corresponding...

  • Page 149

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·149· drill ing an d ta ppin g cycl es penetrating feedrate (f). Place the cursor over this data, key in the desired value and press [enter]. Safety distance. In order to prevent collisions with the...

  • Page 150

    ·150· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x drill ing an d ta ppin g cycl es 3.10.2 drilling cycle. Basic operation the machining steps in this cycle are as follows: 1. If the operation has been programmed with another tool, the cnc wil...

  • Page 151

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·151· drill ing an d ta ppin g cycl es 3.10.3 tapping cycle. Basic operation the machining steps in this cycle are as follows: 1. If the operation has been programmed with another tool, the cnc will...

  • Page 152

    ·152· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x drill ing an d ta ppin g cycl es 3.10.4 multiple drilling cycle. Basic operation the machining steps in this cycle are as follows: 1. If the spindle is working in open loop (rpm or css mode) t...

  • Page 153

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·153· drill ing an d ta ppin g cycl es 3.10.5 multiple threading cycle. Basic operation the machining steps in this cycle are as follows: 1. If the spindle is working in open loop (rpm or css mode) ...

  • Page 154

    ·154· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x drill ing an d ta ppin g cycl es 3.10.6 multiple slot milling cycle. Basic operation the machining steps in this cycle are as follows: 1. If the spindle is working in open loop (rpm or css mod...

  • Page 155

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·155· profilin g cycl e 3.11 profiling cycle level 1. Defining all the points of the profile. Level 2. Using a part-program which contains the profile. Level 3. Zc profile. Available when having a "...

  • Page 156

    ·156· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e 3.11.1 level 1. Profile definition this mode may be used to define the profile by describing its theoretical corners. Up to 12 points may be used in the cycle to define those...

  • Page 157

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·157· profilin g cycl e for a rounded corner, define the rounding radius (r); for a chamfer, define the distance from the theoretical corner to the chamfer point (c). Deleting all the points of a pr...

  • Page 158

    ·158· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e 3.11.2 levels 2, 3 and 4. Profile definition defining the profile program. The profile program may be defined as follows. • key in the profile program number directly. If the...

  • Page 159

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·159· profilin g cycl e 3.11.3 level 2. Optimizing of the machining of a profile if only the desired profile is defined, the cnc assumes that the original stock is cylindrical and machines it as sho...

  • Page 160

    ·160· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e 3.11.4 definition of geometry levels 1 and 2. Zx profile outside or inside profile. When changing the type of profile, the cnc changes the icon and shows the corresponding he...

  • Page 161

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·161· profilin g cycl e coordinates of the starting point (x, z). The coordinates are defined one by one. After placing the cursor on the coordinates of the axes to be defined, the value is entered ...

  • Page 162

    ·162· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e machining direction. When changing the machining direction, the cnc changes the icon and shows the corresponding help screen. Finishing stocks in x-z. Either a single residua...

  • Page 163

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·163· profilin g cycl e 3.11.5 definition of geometry at levels 3 and 4. Xc, zc profiles milling with or without tool radius compensation. When changing the type of profile, the cnc changes the icon...

  • Page 164

    ·164· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e 3.11.6 basic operation at levels 1 and 2. Zx profile the machining steps in this cycle are as follows: 1. If the operation has been programmed with another tool, the cnc will...

  • Page 165

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·165· profilin g cycl e 3.11.7 basic operation at levels 3 and 4. Xc, zc profiles the machining steps in this cycle are as follows: 1. If the operation has been programmed with another tool, the cnc...

  • Page 166

    ·166· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e 3.11.8 example. Level 1 geometry definition. Profile definition. Coordinates (x, z). X 80.0000 z 10.0000 safety distance. X 0.0000 z 0.0000 roughing. Finishing. F 0.800 s 100...

  • Page 167

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·167· profilin g cycl e 3.11.9 examples. Level 2 geometry definition. Profile definition. Modify. Coordinates (x, z). X 65.0000 z 10.0000 outside profile. Type of machining. Work quadrant. Abscissa ...

  • Page 168

    ·168· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e safety distance. X 0.0000 z 0.0000 roughing. Finishing. F 0.800 s 1000 t 3  0.25 spindle. F 1.000 s 1000 t 3  2 rpm.

  • Page 169

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·169· profilin g cycl e geometry definition. Profile definition. Modify. Coordinates (x, z). X 120.0000 z 90.0000 safety distance. X 0.0000 z 0.0000 outside profile. Type of machining. Work quadrant...

  • Page 170

    ·170· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e roughing. Finishing. F 0.800 s 1000 t 3  0.25 spindle. F 1.000 s 1000 t 3  2 rpm.

  • Page 171

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·171· profilin g cycl e geometry definition. Profile definition. Coordinates (x, z). X 230.0000 z 180.0000 safety distance. X 0.0000 z 0.0000 roughing. Finishing. F 0.800 s 1000 t 3  0.25 spindle. ...

  • Page 172

    ·172· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e geometry definition. Profile definition. Definition of the profile of the original stock (new profile). Coordinates (x, z). X 230.0000 z 180.0000 safety distance. X 0.0000 z ...

  • Page 173

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·173· profilin g cycl e roughing. Finishing. F 0.800 s 1000 t 3  0.25 spindle. F 1.000 s 1000 t 3  2 rpm.

  • Page 174

    ·174· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e geometry definition. Profile definition. Coordinates (x, z). X 110.0000 z 190.0000 safety distance. X 0.0000 z 0.0000 roughing. Finishing. F 0.800 s 1000 t 3  0.25 spindle. ...

  • Page 175

    Operating manual cnc 8055 cnc 8055i working with operations or cycles 3. ·tc· o ption s oft : v02.2 x ·175· profilin g cycl e geometry definition. Profile definition. Coordinates (x, z). X 85.0000 z 135.0000 safety distance. X 0.0000 z 0.0000 outside profile. Type of machining. Work quadrant. Abscis...

  • Page 176

    ·176· operating manual cnc 8055 cnc 8055i 3. Working with operations or cycles ·tc· o ption s oft : v02.2 x profilin g cycl e roughing. Finishing. F 0.800 s 1000 t 3  0.25 spindle. F 1.000 s 1000 t 3  2 rpm.

  • Page 177: Y Axis

    Cnc 8055 cnc 8055i ·tc· o ption s oft : v02.2 x 4 ·177· y axis without the y axis option, the y axis will only be available without cycles, calibration or y axis compensation. Both for programming and displaying, the y axis format will always be determined as radius, not as diameter. 4.1 profiling c...

  • Page 178

    ·178· operating manual cnc 8055 cnc 8055i 4. Y axis ·tc· o ption s oft : v02.2 x tool cal ibratio n 4.3 tool calibration there are three tool calibration levels in conversational tc mode managing the y axis: level 1: manual tool calibration and with a probe. Selecting the manual tool calibration usi...

  • Page 179

    Operating manual cnc 8055 cnc 8055i y axis 4. ·tc· o ption s oft : v02.2 x ·179· tool cal ibratio n level 2: tool calibration with probing cycles. Selecting the tool calibration using probing cycles shows, with y axis, the following screen: the y > icon turns on or off the display of the probe's y ...

  • Page 180

    ·180· operating manual cnc 8055 cnc 8055i 4. Y axis ·tc· o ption s oft : v02.2 x tool cal ibratio n.

  • Page 181: Operating In Iso Mode

    Cnc 8055 cnc 8055i ·tc· o ption s oft : v02.2 x 5 ·181· operating in iso mode the iso mode is accessed with the [iso] key. • when operating with operations or cycles, press the [iso] key once. • when operating in jog mode, press the [iso] key twice; the first time to access the mdi mode and the seco...

  • Page 182

    ·182· operating manual cnc 8055 cnc 8055i 5. Op erat ing in is o mode ·tc· o ption s oft : v02.2 x editing blocks in iso mode 5.1 editing blocks in iso mode when accessing the iso mode, the cnc displays a special screen for editing up to 6 program blocks either in iso code or in high level language....

  • Page 183

    Operating manual cnc 8055 cnc 8055i op erat ing in is o mode 5. ·tc· o ption s oft : v02.2 x ·183· p rogramming assistance 5.2 programming assistance 5.2.1 zero offsets and presets 5.2.2 work zones 5.2.3 insert labels and repetitions from label to label the icon may be used to select the following o...

  • Page 184

    ·184· operating manual cnc 8055 cnc 8055i 5. Op erat ing in is o mode ·tc· o ption s oft : v02.2 x p rogramming assistance 5.2.4 mirror image 5.2.5 scaling factor the icons may be used to select the following options: • select the action to be carried out. It is possible to cancel the active mirror ...

  • Page 185: Saving Programs

    Cnc 8055 cnc 8055i ·tc· o ption s oft : v02.2 x 6 ·185· saving programs part-programs may be edited, simulated and executed. Each one of these programs is made up by concatenating simple operations or cycles and/or blocks edited in iso code. Chapter "3 working with operations or cycles" describes ho...

  • Page 186

    ·186· operating manual cnc 8055 cnc 8055i 6. Saving programs ·tc· o ption s oft : v02.2 x list of saved programs 6.1 list of saved programs the cnc will display the following information: press one of these keys to exit the directory or list of part-programs: list of part-programs. The left side sho...

  • Page 187

    Operating manual cnc 8055 cnc 8055i saving programs 6. ·tc· o ption s oft : v02.2 x ·187· see the contents of a pro g ram 6.2 see the contents of a program to see the contents of a part-program, select it on the left column using the pointer. To do that, use the [ ][] keys. The right column shows ...

  • Page 188

    ·188· operating manual cnc 8055 cnc 8055i 6. Saving programs ·tc· o ption s oft : v02.2 x edi t a new pa rt-pro gram 6.3 edit a new part-program to edit a new program, proceed as follows: 1. Press [p.Prog] to access the list of part-programs stored. 2. Select, with the pointer, the option "creating ...

  • Page 189

    Operating manual cnc 8055 cnc 8055i saving programs 6. ·tc· o ption s oft : v02.2 x ·189· savin g an iso block or a cycl e 6.4 saving an iso block or a cycle the block or cycle may be added at the end of the program, after the last operation or insert it between 2 existing operations. To save the bl...

  • Page 190

    ·190· operating manual cnc 8055 cnc 8055i 6. Saving programs ·tc· o ption s oft : v02.2 x delete a ne w p a rt pro g ram 6.5 delete a new part program to delete a part-program, proceed as follows: 1. Press [p.Prog] to access the list of part-programs stored. 2. Select, with the pointer, the part-pro...

  • Page 191

    Operating manual cnc 8055 cnc 8055i saving programs 6. ·tc· o ption s oft : v02.2 x ·191· cop y ing a part-prog ram in to a nother on e 6.6 copying a part-program into another one to copy a part-program into another one, proceed as follows: 1. Press [p.Prog] to access the list of part-programs store...

  • Page 192

    ·192· operating manual cnc 8055 cnc 8055i 6. Saving programs ·tc· o ption s oft : v02.2 x modify a part-program 6.7 modify a part-program to modify a part-program, proceed as follows: 1. Press [p.Prog] to access the list of part-programs stored. 2. Select, with the pointer, the part-program to be mo...

  • Page 193

    Operating manual cnc 8055 cnc 8055i saving programs 6. ·tc· o ption s oft : v02.2 x ·193· modify a part-program 6.7.3 move an operation to another position to move an operation to another position, proceed as follows: 1. Select, with the pointer, the operation to be moved from the right column. Exam...

  • Page 194

    ·194· operating manual cnc 8055 cnc 8055i 6. Saving programs ·tc· o ption s oft : v02.2 x modify a part-program 6.7.4 modify an existing operation to modify an operation, proceed as follows: 1. Select, with the pointer, the block or cycle to be modified from the right column. 2. Press the [recall] k...

  • Page 195

    Operating manual cnc 8055 cnc 8055i saving programs 6. ·tc· o ption s oft : v02.2 x ·195· ma nag ing prog rams usi ng the explo rer 6.8 managing programs using the explorer windows explorer may be accessed from the pprog screen by placing the cursor in the "user programs" area and pressing [recall]....

  • Page 196

    ·196· operating manual cnc 8055 cnc 8055i 6. Saving programs ·tc· o ption s oft : v02.2 x ma nag ing prog rams usi ng the explo rer.

  • Page 197: Execution and Simulation

    Cnc 8055 cnc 8055i ·tc· o ption s oft : v02.2 x 7 ·197· execution and simulation the simulation may be used to graphically show a part-program or an operation with the data used to define it. This way, the simulation may be used to check the part-program or the operation before executing it or savin...

  • Page 198

    ·198· operating manual cnc 8055 cnc 8055i 7. Execution and simulation ·tc· o ption s oft : v02.2 x simula ti ng or executing a n opera ti on or cycl e 7.1 simulating or executing an operation or cycle all the operations or cycles have 2 work modes; execution and editing. Simulation execution an oper...

  • Page 199

    Operating manual cnc 8055 cnc 8055i execution and simulation 7. ·tc· o ption s oft : v02.2 x ·199· simulatin g or e x ecuting a pa rt-pro gram 7.2 simulating or executing a part-program proceed as follows to simulate or execute a part-program: 1. Press [p.Prog] to access the list of part-programs st...

  • Page 200

    ·200· operating manual cnc 8055 cnc 8055i 7. Execution and simulation ·tc· o ption s oft : v02.2 x simula ti ng or executing a n opera ti on th at h a s b een save d 7.3 simulating or executing an operation that has been saved proceed as follows to simulate or execute an operation that has been save...

  • Page 201

    Operating manual cnc 8055 cnc 8055i execution and simulation 7. ·tc· o ption s oft : v02.2 x ·201· execution mod e 7.4 execution mode during execution, both screens show (in the top center window) the number of the program and the number of the cycle being executed. However, when detecting an rpt or...

  • Page 202

    ·202· operating manual cnc 8055 cnc 8055i 7. Execution and simulation ·tc· o ption s oft : v02.2 x execution mod e 7.4.1 tool inspection the plc mark m5050 "toolinsp" determines when tool inspection is enabled. Once tool inspection has been selected, it is possible: • to move the axes to the tool ch...

  • Page 203

    Operating manual cnc 8055 cnc 8055i execution and simulation 7. ·tc· o ption s oft : v02.2 x ·203· graphi c rep resentatio n 7.5 graphic representation the operating manual, t model, "graphics" section of the "execution / simulation" chapter describes how to use the graphics display. However, here i...

  • Page 204

    ·204· operating manual cnc 8055 cnc 8055i 7. Execution and simulation ·tc· o ption s oft : v02.2 x graphi c rep resentatio n graphic parameters • simulation speed. Select on the top right side of the screen the percentage of simulation speed to be applied. Use the [ ][] keys to select the percenta...

  • Page 205

    Operating manual cnc 8055 cnc 8055i execution and simulation 7. ·tc· o ption s oft : v02.2 x ·205· graphi c rep resentatio n once inside the graphic simulation screen, the iso generation maybe selected using the softkey. Then, pressing [cycle start] will generate the program defined by machine param...

  • Page 206

    ·206· operating manual cnc 8055 cnc 8055i 7. Execution and simulation ·tc· o ption s oft : v02.2 x graphi c rep resentatio n.

  • Page 207

    Operating manual cnc 8055 cnc 8055i 7. S oft : v02.2 x ·207·.

  • Page 208

    ·208· operating manual cnc 8055 cnc 8055i 7. S oft : v02.2 x.

  • Page 210

    Fagor automation s. Coop. Bº san andrés, 19 - apdo. 144 e-20500 arrasate-mondragón, spain tel: +34 943 719 200 +34 943 039 800 fax: +34 943 791 712 e-mail: info@fagorautomation.Es www.Fagorautomation.Com fagor automation.