(ref: 1801) 8065 cnc panel pc..
Blank page ·2· machine safety it is up to the machine manufacturer to make sure that the safety of the machine is enabled in order to prevent personal injury and damage to the cnc or to the products connected to it. On start-up and while validating cnc parameters, it checks the status of the followi...
Panel pc. Cnc 8065 ·3· (r ef : 1801) i n d e x about the product - cnc 8065 ..................................................................................................... 5 declaration of ce conformity and warranty conditions ................................................................. 9...
Panel pc. Cnc 8065 ·4· (r ef : 1801) 4.4.2 enclosure design. ...................................................................................................... 78 4.4.3 securing the module. ................................................................................................. 80 4.5 v...
Panel pc. Cnc 8065 ·5· (r ef : 1801) about the product - cnc 8065 basic characteristics. Basic characteristics. 8065 m 8065 m power basic pack 1 basic pack 1 number of execution channels. 1 1 1 1 to 4 number of axes. 3 to 6 5 to 8 5 to 12 8 to 28 number of spindles. 1 1 to 2 1 to 4 1 to 4 maximum nu...
Panel pc. Cnc 8065 ·6· (r ef : 1801) (*) differential ttl / sinusoidal 1 vpp (**) ttl / differential ttl / sinusoidal 1 vpp / ssi protocol / feedat / endat remote modules. Riow rio5 rio70 rior rcs-s valid for cnc. 8070 8065 8060 8070 8065 8060 8070 8065 - - - d i s c o n t i n u e d 8070 8065 8060 8...
Panel pc. Cnc 8065 ·7· (r ef : 1801) software options. Some of the features described in this manual are dependent on the acquired software options. The active software options for the cnc can be consulted in the diagnostics mode (accessible from the task window by pressing [ctrl] [a]), under softwa...
Panel pc. Cnc 8065 ·8· (r ef : 1801) soft iip conversational interactive icon-based pages (conversational mode). Iip or conversational mode is specifically designed for people without any prior programming knowledge or for those that are not familiarized with fagor cnc's. Working in conversational m...
Panel pc. Cnc 8065 ·9· (r ef : 1801) declaration of ce conformity and warranty conditions declaration of conformity the declaration of conformity for the cnc is available in the downloads section of fagor’s corporate website. Http://www.Fagorautomation.Com. (type of file: declaration of conformity)....
Blank page ·10·.
Panel pc. Cnc 8065 ·11· (r ef : 1801) version history - cnc 8065 here is a list of the features added to each manual reference. Ref. 1709 ref. 1801 first version. Corrected errors..
Blank page ·12·.
Panel pc. Cnc 8065 ·13· (r ef : 1801) safety conditions read the following safety measures in order to prevent harming people or damage to this product and those products connected to it. Fagor automation shall not be held responsible of any physical or material damage originated from not complying ...
Panel pc. Cnc 8065 ·14· (r ef : 1801) precautions against damage to the product safety symbols symbols that may appear in the manual. Work environment. This unit is ready to be used in industrial environments complying with the directives and regulations effective in the european community. Fagor au...
Panel pc. Cnc 8065 ·15· (r ef : 1801) symbols that the product may carry. Ground symbol. This symbol indicates that that point must be under voltage. Esd components. This symbol identifies the cards as esd components (sensitive to electrostatic discharges)..
Blank page ·16·.
Panel pc. Cnc 8065 ·17· (r ef : 1801) returning conditions pack it in its original package along with its original packaging material. If you do not have the original packaging material, pack it as follows: 1 get a cardboard box whose 3 inside dimensions are at least 15 cm (6 inches) larger than tho...
Blank page ·18·.
Panel pc. Cnc 8065 ·19· (r ef : 1801) cnc maintenance cleaning the accumulated dirt inside the unit may act as a screen preventing the proper dissipation of the heat generated by the internal circuitry which could result in a harmful overheating of the unit and, consequently, possible malfunctions. ...
Blank page ·20·.
Panel pc. Cnc 8065 1. ·21· (r ef : 1801) pr evious information. 1 previous information. About this manual. This manual describes the characteristics, technical data and connections of the hardware associated with the cnc. The installation manual describes the cnc configuration, machine adaptation an...
Panel pc. Cnc 8065 1. ·22· (r ef : 1801) pr evious information..
Panel pc. Cnc 8065 2. ·23· (r ef : 1801) monitor-21 multitouch. 2 monitor-21 multitouch. Monitor to display the vga video signal from the central unit and also to serve as the touch screen, permitting interaction with the central unit. This monitor may be the only one connected to the central unit (...
Panel pc. Cnc 8065 2. ·24· (r ef : 1801) monitor-21 multitouch. 2.1 specifications. Type. Description. Monitor-21w multitouch monitor-21w multitouch neutro general. • 21.5" (1920 × 1080) monitor, multi-touch screen (10 points) and usb driver. • dimensions (width x height x depth) - 558.40 × 349.80 ×...
Panel pc. Cnc 8065 2. ·25· (r ef : 1801) monitor-21 multitouch. 2.2 general diagram (monitor-21 multitouch). (*) for lengths greater than 5 meters, use a ppc-21w or ppc-19. Can can op panel monitor-21w multitouch monitor-21w multitouch neutro vga t/s usb cnc u65 cnc u70 horizontal keyb vertical keyb...
Panel pc. Cnc 8065 2. ·26· (r ef : 1801) monitor-21 multitouch. 2.3 dimensions. Mm inch a 558.40 21.98 b 349.80 13.77 c 40.70 1.60 d 47.70 1.88 mm inch da 548.00 21.57 db 339.25 13.36 da c db a b d.
Panel pc. Cnc 8065 2. ·27· (r ef : 1801) monitor-21 multitouch. 2.4 enclosure and mounting of the module. 2.4.1 enclosure design. The enclosure must meet the following requirements: • the degree of protection of the enclosure must be ip54, according to standard iec 60529. • keep the enclosure clean....
Panel pc. Cnc 8065 2. ·28· (r ef : 1801) monitor-21 multitouch. 2.4.2 securing the module. The module must be installed in a proper enclosure that may be located on the machine or on an external support. To insert the unit into the enclosure, it must have a big enough hole to allow to insert it easi...
Panel pc. Cnc 8065 2. ·29· (r ef : 1801) monitor-21 multitouch. 4 fasten the monitor on the rear, using all the fastening hooks (d). D 1 2 0.7 nm.
Panel pc. Cnc 8065 2. ·30· (r ef : 1801) monitor-21 multitouch. 2.5 voltage supply for the module. The monitor has two power supply connections. Fagor automation recommends using 24 v dc (phoenix-type connector) to power the monitor. Consult fagor automation before using the 12 v dc option. 24 v dc ...
Panel pc. Cnc 8065 2. ·31· (r ef : 1801) monitor-21 multitouch. 2.6 configuring the video signal from the monitor. The buttons to configure the monitor are on the back. Button . Description. Turns the monitor on and off. Automatically adjusts the clock, phase, horizontal position and vertical positi...
Panel pc. Cnc 8065 2. ·32· (r ef : 1801) monitor-21 multitouch. 2.7 connectors. ·t/s rs232· touch screen driver (not recommended). ·t/s usb· touch screen driver (recommended). Option recommended by fagor automation for the touch controller. Bottom view. (a) t/s rs-232 touch screen driver (consult fa...
Panel pc. Cnc 8065 2. ·33· (r ef : 1801) monitor-21 multitouch. ·24 v dc in· supply input (recommended). Option recommended by fagor automation to power the monitor. ·12 v dc in· supply input (not recommended). ·vga· video input. ·dvi-d· video input. Connector data. Number of poles. 3. Pitch. 5.08 m...
Panel pc. Cnc 8065 2. ·34· (r ef : 1801) monitor-21 multitouch. 2.8 cable characteristics. 2.8.1 vga video signal. Connector pinout. Cable characteristics. Use specific vga cable. Node connection. Use the vga output of the central unit. The connection is parallel, 1 with 1, 2 with 2, etc. The cable ...
Panel pc. Cnc 8065 2. ·35· (r ef : 1801) monitor-21 multitouch. 2.9 osd (on screen display) menu. The selected values are stored in the memory of the monitor after pressing the [menu/sel] button at the end of the wait time. The saved values are not lost when the monitor is turned off. However, the s...
Panel pc. Cnc 8065 2. ·36· (r ef : 1801) monitor-21 multitouch. 2.9.2 osd menu. To display the osd menu, press the menu key on the back of the monitor. Icon. Description. Video input. Contrast/brightness. Geometry (for dvi input). Temperature color. Language. Osd configuration. Auto-configuration. I...
Panel pc. Cnc 8065 2. ·37· (r ef : 1801) monitor-21 multitouch. Video input. Osd sub-menu. Contrast/brightness. Osd sub-menu. Select this menu icon using the [left] and [right] keys and press the [menu/sel] key to confirm the selection. Select this menu icon using the [left] and [right] keys and pre...
Panel pc. Cnc 8065 2. ·38· (r ef : 1801) monitor-21 multitouch. Geometry (for dvi input). Osd sub-menu. Temperature color. Osd sub-menu. Language. Osd sub-menu. Select this menu icon using the [left] and [right] keys and press the [menu/sel] key to confirm the selection. Select this menu icon using ...
Panel pc. Cnc 8065 2. ·39· (r ef : 1801) monitor-21 multitouch. Osd configuration. Osd sub-menu. Auto-configuration. Osd sub-menu. Information. Osd sub-menu. Select this menu icon using the [left] and [right] keys and press the [menu/sel] key to confirm the selection. Select this menu icon using the...
Panel pc. Cnc 8065 2. ·40· (r ef : 1801) monitor-21 multitouch. Restore. Osd sub-menu. Exit. Osd sub-menu. Select this menu icon using the [left] and [right] keys and press the [menu/sel] key to confirm the selection. Select this menu icon using the [left] and [right] keys and press the [menu/sel] k...
Panel pc. Cnc 8065 2. ·41· (r ef : 1801) monitor-21 multitouch. 2.9.3 locks and unlocks the osd menu. Locks the osd menu. Unlocking the osd menu. Note: all images of the osd menu are property of advantech co., ltd. Press the [left]+[right] keys and the following message will appear on screen. Do not...
Panel pc. Cnc 8065 2. ·42· (r ef : 1801) monitor-21 multitouch..
Panel pc. Cnc 8065 3. ·43· (r ef : 1801) ppc-21w. 3 ppc-21w. Panel pc with 21.5 multi-touch monitor to control, operate and monitor the cnc via an ethernet connection. The ppc-21w allows the user to operate the cnc using the touch screen or a usb keyboard (for example, the horizontal keyb 2.0 + touc...
Panel pc. Cnc 8065 3. ·44· (r ef : 1801) ppc-21w. 3.1 specifications. Type. Description. General. • 21.5" (1920 × 1080 pixel) multi-touch screen monitor (10 points of contact) and usb controller. • dimensions (width x height x depth) - 558.40 × 349.80 × 121.41 mm. - 21.98" × 13.77" × 4.78". • weight...
Panel pc. Cnc 8065 3. ·45· (r ef : 1801) ppc-21w. 3.2 general diagram (ppc-21w). 3.2.1 networking, without access to the company network. Can horizontal keyb 2.0 + touchpad usb 2.0 ppc-21w hbh3 handheld terminal cnc u65 cnc u70 ethernet ethernet op panel connection. Description. Usb 2.0 connection o...
Panel pc. Cnc 8065 3. ·46· (r ef : 1801) ppc-21w. 3.2.2 connecting to an ethernet network via the pc-panel. Ethernet company network can horizontal keyb 2.0 + touchpad usb 2.0 ppc-21w hbh3 handheld terminal cnc u65 cnc u70 ethernet ethernet op panel connection. Description. Usb 2.0 connection of a u...
Panel pc. Cnc 8065 3. ·47· (r ef : 1801) ppc-21w. 3.2.3 connecting to an ethernet network through a switch. Can usb 2.0 ethernet company network ppc-21w ethernet ethernet switch sfnb 5tx ethernet horizontal keyb 2.0 + touchpad hbh3 handheld terminal cnc u65 cnc u70 op panel connection. Description. ...
Panel pc. Cnc 8065 3. ·48· (r ef : 1801) ppc-21w. 3.3 dimensions. Mm inch a 558.40 21.98 b 349.80 13.77 c 114.41 4.50 d 121.41 4.78 mm inch da 548.00 21.57 db 339.25 13.36 da db a b d c.
Panel pc. Cnc 8065 3. ·49· (r ef : 1801) ppc-21w. 3.4 enclosure and mounting of the module. 3.4.1 ambient characteristics of the enclosure. The enclosure must ensure that the temperature inside does not exceed 55 °c (131 °f) while the device is in operating mode, with an ambient temperature of 45 ºc...
Panel pc. Cnc 8065 3. ·50· (r ef : 1801) ppc-21w. Recommended minimum clearances between the ppc-21w and the enclosure walls. Dissipated power inside the enclosure. To calculate the total surface area the enclosure must have to dissipate the heat inside, we must consider the dissipated power for all...
Panel pc. Cnc 8065 3. ·51· (r ef : 1801) ppc-21w. 3.4.3 securing the module. The module must be installed in a proper enclosure that may be located on the machine or on an external support. To insert the unit into the enclosure, it must have a big enough hole to allow to insert it easily, without ob...
Panel pc. Cnc 8065 3. ·52· (r ef : 1801) ppc-21w. 3 rest the monitor inside the enclosure on the lower stop screws and push the top part until the pressure hooks support the monitor. 4 fasten the ppc-21w at the rear, using all the attachment fixtures (d). D 1 2 0.7 nm.
Panel pc. Cnc 8065 3. ·53· (r ef : 1801) ppc-21w. 3.5 voltage supply for the module. The monitor and the panel pc require separate power supplies; it is necessary to power both modules. The monitor has two different voltage power supply ports (24 and 12 v dc). Fagor automation recommends using 24 v ...
Panel pc. Cnc 8065 3. ·54· (r ef : 1801) ppc-21w. 3.6 hardware functionalities. 3.6.1 rear keyboard. The rear keyboard allows the monitor video signal ( "3.7 configuring the video signal from the monitor." ) to be configured and to navigate through the osd menu ( "3.9 osd (on screen display) menu." ...
Panel pc. Cnc 8065 3. ·55· (r ef : 1801) ppc-21w. 3.6.2 monitor (lower end connectors). ·t/s usb· touch screen driver. Connect the monitor’s t/s usb (touch controller) output to a usb 2.0 port on the panel pc. Always use the cable supplied by fagor for the unit. ·24 v dc in· supply input (recommende...
Panel pc. Cnc 8065 3. ·56· (r ef : 1801) ppc-21w. 3.6.3 panel pc (lower end connectors). ·usb 2.0· 2 usb 2.0 type-a ports. ·usb 3.0· 2 usb 3.0 type-a ports. ·hdmi · hdmi output to monitor. ·vga· vga video output to monitor. Bottom view. (a) usb 2.0 / usb 3.0 2 usb 2.0 type-a ports. 2 usb 3.0 type-a ...
Panel pc. Cnc 8065 3. ·57· (r ef : 1801) ppc-21w. ·lan a / lan b· ethernet. The ppc-21w has 4 rj45 lan ports, two at the lower end (lan a / lan b) and two at the upper end (lan c / lan d). All ports comply with the ieee 802.3u 10 / 100base-t csma/cd standard and are compliant with the ieee 802.3ab 1...
Panel pc. Cnc 8065 3. ·58· (r ef : 1801) ppc-21w. Power button. ·rst· reset button. ·tx rx· transmission and reception leds. ·btr· battery status led. ·hdd· hard drive activity led. ·pwr· power status led. Button to turn the panel pc on and off. Button to activate the hardware reset function. Data t...
Panel pc. Cnc 8065 3. ·59· (r ef : 1801) ppc-21w. 3.6.4 panel pc (top end connectors). ·com1 / com2· rs-232 serial line. 2 com ports for rs-232 serial lines, 50 ~ 115.2 kbps. ·lan a / lan b· ethernet. The ppc-21w has 4 rj45 lan ports, two at the lower end (lan a / lan b) and two at the upper end (la...
Panel pc. Cnc 8065 3. ·60· (r ef : 1801) ppc-21w. 3.7 configuring the video signal from the monitor. The buttons to configure the monitor video signal are on the back. This keyboard is also used for the osd menu. Button. Description. Turns the monitor on and off. Automatically adjusts the clock, pha...
Panel pc. Cnc 8065 3. ·61· (r ef : 1801) ppc-21w. 3.8 connection. 3.8.1 vga video signal. Connect the panel pc’s pcvga output to the monitor’s vga input. Cable characteristics. Fagor automation supplies the necessary cable for the vga connection between the panel pc and the monitor. Always use the c...
Panel pc. Cnc 8065 3. ·62· (r ef : 1801) ppc-21w. 3.8.2 touch controller. Connect the monitor’s t/s usb (touch controller) output to a usb 2.0 port on the panel pc. Cable characteristics. Fagor automation supplies the necessary cable for the touch controller. Always use the cable supplied by fagor f...
Panel pc. Cnc 8065 3. ·63· (r ef : 1801) ppc-21w. 3.8.3 ethernet (fast ethernet / gigabit ethernet). The ppc-21w has 4 rj45 lan ports, two at the lower end (lan a / lan b) and two at the upper end (lan c / lan d). All ports comply with the ieee 802.3u 10 / 100base-t csma/cd standard and are complian...
Panel pc. Cnc 8065 3. ·64· (r ef : 1801) ppc-21w. Element connection. In order to ensure proper performance, the connection cable must be inserted all the way into the connectors so they're latched. This ensures that the cable is properly latched and does not come off due to vibration..
Panel pc. Cnc 8065 3. ·65· (r ef : 1801) ppc-21w. 3.9 osd (on screen display) menu. The selected values are stored in the memory of the monitor after pressing the [menu/sel] button at the end of the wait time. The saved values are not lost when the monitor is turned off. However, the selected value ...
Panel pc. Cnc 8065 3. ·66· (r ef : 1801) ppc-21w. 3.9.2 osd menu. To display the osd menu, press the menu key on the back of the monitor. Icon. Description. Video input. Contrast/brightness. Geometry (for dvi input). Temperature color. Language. Osd configuration. Auto-configuration. Information. Re...
Panel pc. Cnc 8065 3. ·67· (r ef : 1801) ppc-21w. Video input. Osd sub-menu. Contrast/brightness. Osd sub-menu. Select this menu icon using the [left] and [right] keys and press the [menu/sel] key to confirm the selection. Select this menu icon using the [left] and [right] keys and press the [menu/s...
Panel pc. Cnc 8065 3. ·68· (r ef : 1801) ppc-21w. Geometry (for dvi input). Osd sub-menu. Temperature color. Osd sub-menu. Language. Osd sub-menu. Select this menu icon using the [left] and [right] keys and press the [menu/sel] key to confirm the selection. Select this menu icon using the [left] and...
Panel pc. Cnc 8065 3. ·69· (r ef : 1801) ppc-21w. Osd configuration. Osd sub-menu. Auto-configuration. Osd sub-menu. Information. Osd sub-menu. Select this menu icon using the [left] and [right] keys and press the [menu/sel] key to confirm the selection. Select this menu icon using the [left] and [r...
Panel pc. Cnc 8065 3. ·70· (r ef : 1801) ppc-21w. Restore. Osd sub-menu. Exit. Osd sub-menu. Select this menu icon using the [left] and [right] keys and press the [menu/sel] key to confirm the selection. Select this menu icon using the [left] and [right] keys and press the [menu/sel] key to confirm ...
Panel pc. Cnc 8065 3. ·71· (r ef : 1801) ppc-21w. 3.9.3 locks and unlocks the osd menu. Locks the osd menu. Unlocking the osd menu. Note: all images of the osd menu are property of advantech co., ltd. Press the [left]+[right] keys and the following message will appear on screen. Do not release the k...
Panel pc. Cnc 8065 3. ·72· (r ef : 1801) ppc-21w..
Panel pc. Cnc 8065 4. ·73· (r ef : 1801) ppc-19. 4 ppc-19. Panel pc with 19 multi-touch monitor to control, operate and monitor the cnc via an ethernet connection. The ppc-19 allows the user to operate the cnc using the touch screen or a usb keyboard (for example, the horizontal keyb 2.0 + trackhpad...
Panel pc. Cnc 8065 4. ·74· (r ef : 1801) ppc-19. 4.1 specifications. Type. Description. General. • 19" monitor (1280 × 1024 px), capacitive multi-touch (10 points). • so: windows 7. • dimensions (width x height x depth) - 480 × 400 × 60.40 mm. - 18.90" × 15.75" × 2.37". • weight: 7.6 kg (16.75 lb) r...
Panel pc. Cnc 8065 4. ·75· (r ef : 1801) ppc-19. 4.2 general diagram (ppc-19 ). 4.2.1 point-to-point connection with the cnc. Usb 2.0 ppc-19 ethernet ethernet can horizontal keyb 2.0 + touchpad hbh3 handheld terminal cnc u65 cnc u70 op panel connection. Description. Usb 2.0 connection of a usb keybo...
Panel pc. Cnc 8065 4. ·76· (r ef : 1801) ppc-19. 4.2.2 connecting to an ethernet network through a switch. Can usb 2.0 ethernet company network ppc-19 ethernet ethernet switch sfnb 5tx ethernet horizontal keyb 2.0 + touchpad hbh3 handheld terminal cnc u65 cnc u70 op panel connection. Description. Us...
Panel pc. Cnc 8065 4. ·77· (r ef : 1801) ppc-19. 4.3 dimensions. Mm inch a 480 18.90 b 400 15.75 c 52.60 2.07 d 60.40 2.37 mm inch da 461 18.15 db 381 15 da db a b c d.
Panel pc. Cnc 8065 4. ·78· (r ef : 1801) ppc-19. 4.4 enclosure and mounting of the module. 4.4.1 ambient characteristics of the enclosure. The enclosure must ensure that the temperature inside does not exceed 55 c (131 ºf) while the device is in operating mode, with an ambient temperature of 45 ºc (...
Panel pc. Cnc 8065 4. ·79· (r ef : 1801) ppc-19. Minimum distances recommended to the enclosure walls. Dissipated power inside the enclosure. To calculate the total surface area the enclosure must have to dissipate the heat inside, we must consider the dissipated power for all the elements that gene...
Panel pc. Cnc 8065 4. ·80· (r ef : 1801) ppc-19. 4.4.3 securing the module. The module must be installed in a proper enclosure that may be located on the machine or on an external support. To insert the unit into the enclosure, it must have a big enough hole to allow to insert it easily, without obs...
Panel pc. Cnc 8065 4. ·81· (r ef : 1801) ppc-19. 4.5 voltage supply for the module. Monitor power: 12 ~ 24 v dc. Power the monitor with a 12 ~ 24 v dc power supply. Consumption. • consumption (12 v dc): 23 w (minimum); 43 w (maximum). • consumption (24 v dc): 23 w (minimum); 45 w (maximum). Power su...
Panel pc. Cnc 8065 4. ·82· (r ef : 1801) ppc-19. 4.6 hardware functionality. Connectors. Connector. Description. A usb 2.0 2 usb 2.0 type-a ports. B rs-232/422/485 2 rs-232/422/485 serial lines. C dvi-d video signal output. D usb 2.0 1 usb 2.0 type-a ports. E usb 3.0 1 usb 3.0 type-a ports. F lan 2 ...
Panel pc. Cnc 8065 4. ·83· (r ef : 1801) ppc-19. ·lan· ethernet. 2 rj45 lan ports (10/100/1000 mbps). ·hdd led· hard drive activity led. ·power led· power status led. ·24 v dc in· supply input (recommended). Option recommended by fagor automation to power the monitor. Hard drive activity led (red le...
Panel pc. Cnc 8065 4. ·84· (r ef : 1801) ppc-19. 4.7 connection. 4.7.1 ethernet (fast ethernet / gigabit ethernet). The ppc-19 can be configured as an additional node on a local network or it may be connected point-to-point to the cnc. Connector. All ports have two leds to indicate whether the ppc-1...
Panel pc. Cnc 8065 5. ·85· (r ef : 1801) fagor c onn e ct application. 5 fagorconnect application. The fagorconnect application makes it possible to simplify the configuration of the connection between a panel pc and the cnc. This application can be installed on "fagor" pc panels or on any pc that w...
Panel pc. Cnc 8065 5. ·86· (r ef : 1801) fagor c onn e ct application. 5.2 the fagorconnect application. The main objective of the application is to connect the panel pc to the cnc through the remote desktop as soon as the application starts and in a way that is transparent to the user. After establ...
Panel pc. Cnc 8065 5. ·87· (r ef : 1801) fagor c onn e ct application. 5.3 configure the application. The "configuration" button at the top shows the window to configure the connection to the cnc. When the application starts, it displays the current configuration saved in the fagorconnect.Ini file. ...
Panel pc. Cnc 8065 5. ·88· (r ef : 1801) fagor c onn e ct application. 5.4 work modes. The "protection" button at the top shows the window to select the operating mode of the panel pc (user mode or administrator mode). These operating modes are not available when the fagorconnect application is inst...
Panel pc. Cnc 8065 5. ·89· (r ef : 1801) fagor c onn e ct application. 5.5 diagnosis. The "diagnosis" button at the top shows information about the panel pc itself. The "save to file" button allows you to save the information in a file. 5.6 accessing panel pc resources from the cnc. The panel pc is ...
Panel pc. Cnc 8065 5. ·90· (r ef : 1801) fagor c onn e ct application..
Panel pc. Cnc 8065 ·91· user notes: (r ef : 1801).
Panel pc. Cnc 8065 ·92· user notes: (r ef : 1801).
Panel pc. Cnc 8065 ·93· user notes: (r ef : 1801).
Fagor automation s. Coop. Bº san andrés, 19 - apdo. 144 e-20500 arrasate-mondragón, spain tel: +34 943 719 200 +34 943 039 800 fax: +34 943 791 712 e-mail: info@fagorautomation.Es www.Fagorautomation.Com.
