Fagor CNC8 070 Error Code List - Errors 1000-1999

Manual is about: ERROR SOLUTIONS

Summary of CNC8 070

  • Page 1

    Cnc8070 r ef . 04 02 err o r solutions.

  • Page 3

    Cnc8070 r ef . 0402 e rror solutions unauthorized copying or distributing of this software is prohibited. All rights reserved. No part of this documentation may be transmitted, transcribed, stored in a backup device or translated into another language without fagor automation’s consent. Microsoft ® ...

  • Page 5: Index

    Cnc8070 e rror solutions index page i of i index errors 0000-0999 ....................................................................................1 errors 1000-1999 ....................................................................................9 errors 2000-2999 ...............................

  • Page 7: Errors 0000-0999

    Cnc8070 r ef . 0402 e rror solutions page 1 of 128 errors 0000-0999 errors 0000-0999 0001 'system error' detection during execution. Cause software or hardware error that cause corrupt data and/or incoherent results. Solution this type of errors usually force the cnc output. Contact your supplier. 0...

  • Page 8: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 2 of 128 errors 0000-0999 0040 'm before-before or before-after with subroutine does not admit movements in the block' detection machine parameter validation. Cause an m function with associated subroutine cannot be before-before or before-after. The ...

  • Page 9

    Cnc8070 r ef . 0402 e rror solutions page 3 of 128 errors 0000-0999 0049 ''a master axis cannot be a slave and vice versa' detection machine parameter validation. Cause if an axis is set as slave in another gantry pair, cannot be the master of another pair. An axis already set as master cannot be th...

  • Page 10: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 4 of 128 errors 0000-0999 0058 'the cnc must be restarted too assume the changes in the hmi table,' detection machine parameter validation. Cause the cnc must be restarted in order to assume the changes made to the hmi table. Solution restart the cnc....

  • Page 11

    Cnc8070 r ef . 0402 e rror solutions page 5 of 128 errors 0000-0999 0069 'gantry axes: the slave cannot have decinput (home switch) if the master does not have one' detection machine parameter validation. Cause an axis of a gantry pair cannot be homed with a home switch (decinput = true). Solution d...

  • Page 12: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 6 of 128 errors 0000-0999 0079 'a gantry slave axis cannot be parked' detection validation of machine parameters or startup processes. Cause the parked signal of the gantry slave axis is active. While powering the cnc up, it has been detected that the...

  • Page 13

    Cnc8070 r ef . 0402 e rror solutions page 7 of 128 errors 0000-0999 0089 'it starts up with a single channel due to errors detected in machine parameters.' detection machine parameter validation. Cause errors or warnings have come up while validating machine parameters related to the axes or spindle...

  • Page 14: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 8 of 128 errors 0000-0999 0105 'parameters cannot be validated while executing a program' detection during execution. Cause an attempt has been made to validate a machine parameter table while the program is in execution or interrupted. Solution finis...

  • Page 15: Errors 1000-1999

    Cnc8070 r ef . 0402 e rror solutions page 9 of 128 errors 1000-1999 errors 1000-1999 1000 'the function of instruction requires programming the axes' detection during execution. Cause the axes affected by the programmed instruction or g function have not been programmed. Solution check the program. ...

  • Page 16: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 10 of 128 errors 1000-1999 1010 'program g4 k' detection during execution. Cause the function has not been programmed correctly. Solution there are two ways to program the dwell with g4: • g4 • g4 k . In both cases, the dwell must be programmed after ...

  • Page 17

    Cnc8070 r ef . 0402 e rror solutions page 11 of 128 errors 1000-1999 1019 'no measurement has been taken on the requested axis (axes)' detection during execution. Cause function g101is being used to include the measurement offset on an axis for which: • no previous measurement has been taken (g100)....

  • Page 18: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 12 of 128 errors 1000-1999 1028 'the difference between the programmed center and the calculated one is too large' detection during execution. Cause in a circular interpolation with function 265 active, the difference between the initial radius and th...

  • Page 19

    Cnc8070 r ef . 0402 e rror solutions page 13 of 128 errors 1000-1999 1040 'home search not allowed on an axis in g201' detection during execution. Cause an axis cannot be homed if it is in additive manual mode (g201). Solution use function g202 to cancel the additive manual mode of the axis in order...

  • Page 20: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 14 of 128 errors 1000-1999 1050 'considering the tool offsets, it exceeds the data range' detection during execution. Cause the tool dimensions exceed the maximum values. Solution modify the tool dimensions. 1052 'values resulting from the measurement...

  • Page 21

    Cnc8070 r ef . 0402 e rror solutions page 15 of 128 errors 1000-1999 1063 'incompatible g functions (g108/g109/g193)' detection during execution. Cause two or more g functions of the same group cannot be programmed in the same block. Solution program them in different blocks. 1064 'incompatible g fu...

  • Page 22: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 16 of 128 errors 1000-1999 1075 'incompatible g functions (g96/g97/g192)' detection during execution. Cause two or more g functions of the same group cannot be programmed in the same block. Solution program them in different blocks. 1077 'incompatible...

  • Page 23

    Cnc8070 r ef . 0402 e rror solutions page 17 of 128 errors 1000-1999 1090 'nonexistent h function' detection during execution. Cause the programmed h function does not exist. Solution the maximum h function number is 65534. 1091 't function programmed twice' detection during execution. Cause more th...

  • Page 24: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 18 of 128 errors 1000-1999 1101 '#set ipopos instruction programmed wrong' detection during execution. Cause the possible causes are: • the syntax of the instruction is wrong. • only the block number of a label may be programmed in the same block as t...

  • Page 25

    Cnc8070 r ef . 0402 e rror solutions page 19 of 128 errors 1000-1999 1109 'wrong axis index' detection during execution. Cause in functions g20 and g74, an index must be programmed with the axis name. That index is wrong. Solution the axis index must be greater than 0 and must not exceed the maximum...

  • Page 26: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 20 of 128 errors 1000-1999 1119 'the $switch instruction must be programmed alone in the block' detection during execution. Cause control instructions must be programmed alone in the block. Solution check the program. 1120 '$case not expected' detecti...

  • Page 27

    Cnc8070 r ef . 0402 e rror solutions page 21 of 128 errors 1000-1999 1130 'the $endfor instruction must be programmed alone in the block' detection during execution. Cause control instructions must be programmed alone in the block. Solution check the program. 1131 'the $while instruction must be pro...

  • Page 28: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 22 of 128 errors 1000-1999 1141 'the $continue instruction must be programmed alone in the block' detection during execution. Cause control instructions must be programmed alone in the block. Solution check the program. 1142 'the #time instruction mus...

  • Page 29

    Cnc8070 r ef . 0402 e rror solutions page 23 of 128 errors 1000-1999 1154 'file name too long' detection during execution. Cause the maximum number of characters allowed for the name of a program or subroutine has been exceeded. • the name of a program or subroutine may have a maximum of 63 characte...

  • Page 30: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 24 of 128 errors 1000-1999 1162 'm17/m29/#ret not expected' detection during execution. Cause m17/m29/#ret has been detected as end of program. Solution program m30/m02 as the end of the main program. If the error persists, check that all the local su...

  • Page 31

    Cnc8070 r ef . 0402 e rror solutions page 25 of 128 errors 1000-1999 1172 'instruction not allowed while tool radius compensation is active' detection during execution. Cause an attempt has been made to activate a function that is incompatible with tool radius compensation. Solution cancel tool radi...

  • Page 32: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 26 of 128 errors 1000-1999 1181 '#link: an axis active in g201 cannot be defined as slave' detection during execution. Cause an attempt has been made to define as slave of a coupling an axis that is in additive manual mode with function g201. Solution...

  • Page 33

    Cnc8070 r ef . 0402 e rror solutions page 27 of 128 errors 1000-1999 1191 '#incjog: negative or zero incremental jog distances are not allowed' detection during execution. Cause a negative or zero value has been programmed for incremental jog distance. Solution the value of the incremental movement ...

  • Page 34: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 28 of 128 errors 1000-1999 1203 'the #set ipopos instruction must be programmed alone in the block' detection during execution. Cause only the block number of a label may be programmed in the same block as a "#" instruction. Solution check the program...

  • Page 35

    Cnc8070 r ef . 0402 e rror solutions page 29 of 128 errors 1000-1999 1215 'the #call ax/#set ax instruction must be programmed alone in the block' detection during execution. Cause only the block number of a label may be programmed in the same block as a "#" instruction. Solution check the program. ...

  • Page 36: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 30 of 128 errors 1000-1999 1225 'division by zero' detection during execution. Cause an operation has been programmed whose execution involves dividing by zero. Solution it is only possible to divide by numbers other than zero. When working with param...

  • Page 37

    Cnc8070 r ef . 0402 e rror solutions page 31 of 128 errors 1000-1999 1244 'face axis close to the center: the spindle speed in g96 has been limited' detection during execution. Cause while working at constant surface speed, the spindle speed has been limited. The limitation is due to the proximity o...

  • Page 38: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 32 of 128 errors 1000-1999 1256 'acceleration percentage out of range' detection during execution. Cause the acceleration percentage programmed with function g130 is too high. Solution the maximum value allowed for the acceleration percentage is 21474...

  • Page 39

    Cnc8070 r ef . 0402 e rror solutions page 33 of 128 errors 1000-1999 1265 'programming not allowed while rtcp/tlc is active' detection during execution. Cause an attempt has been made to execute one of the following functions while rtcp or tlc is active. • home search (g74). • modify software limits...

  • Page 40: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 34 of 128 errors 1000-1999 1278 'g131/g133: wrong value' detection during execution. Cause the possible causes are: • function g131 has been used to program the wrong value for the percentage of acceleration to be applied to the axes. • function g133 ...

  • Page 41

    Cnc8070 r ef . 0402 e rror solutions page 35 of 128 errors 1000-1999 1288 'too many parameters programmed in the instruction' detection during execution. Cause the instruction has not been programmed correctly. Solution check the syntax of the instruction in the programming manual. 1290 'i, j, k coo...

  • Page 42: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 36 of 128 errors 1000-1999 1305 'programming not allowed while #mcs is active' detection during execution. Cause one of the following functions has been programmed while #mcs is active: • zero offsets (g54-g59, g159, g92, g158, g101, g102, g53) on/off...

  • Page 43

    Cnc8070 r ef . 0402 e rror solutions page 37 of 128 errors 1000-1999 1315 '#cs on/#acs on: undefined system' detection during execution. Cause the #cs on/#acs on instruction has been programmed without parameters, but no transformation has been defined or activated previously. Solution when programm...

  • Page 44: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 38 of 128 errors 1000-1999 1325 'block number defined several times' detection during execution. Cause the same block number "n" has been defined several times in different points of the program. Solution do not repeat the block number. 1326 'wrong va...

  • Page 45

    Cnc8070 r ef . 0402 e rror solutions page 39 of 128 errors 1000-1999 1337 'no caxis has been defined' detection during execution. Cause none of the axes programmed in the #face/#cyl instruction is a c axis. Solution one of the two axes programmed in the instruction must be a c axis. In other words, ...

  • Page 46: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 40 of 128 errors 1000-1999 1349 'negative axis coordinate when activating #face' detection during execution. Cause the linear axis that is part of the face c axis transformation is positioned in the negative portion with respect to the rotating axis. ...

  • Page 47

    Cnc8070 r ef . 0402 e rror solutions page 41 of 128 errors 1000-1999 1360 'g33/g63/g95/g96/g97 not allowed while the c axis is active' detection during execution. Cause a g33/g63/g95/g96/g97 function has been programmed while the c axis was active. Solution the c axis may be deactivated with the #ca...

  • Page 48: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 42 of 128 errors 1000-1999 1376 'no default name has been defined for the c axis' detection during execution. Cause the #cax instruction has been programmed with no parameters, the name given to the master spindle of the channel to work as c axis is t...

  • Page 49

    Cnc8070 r ef . 0402 e rror solutions page 43 of 128 errors 1000-1999 1385 'd and the tool length cannot be modified in the same block' detection during execution. Cause an attempt has been made to write the "v.G.Tol" variable in the same block where a tool change or tool offset change is programmed....

  • Page 50: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 44 of 128 errors 1000-1999 1394 'the subroutine associated with the g function does not exist' detection during execution. Cause the possible causes are: • function g74 has been programmed alone in the block, but it has no subroutine associated with m...

  • Page 51

    Cnc8070 r ef . 0402 e rror solutions page 45 of 128 errors 1000-1999 1403 '#link: a coupling (slaving) cannot be defined with a hirth axis deactivated' detection during execution. Cause an attempt has been made to activate a coupling between hirth axis while one of them is deactivated. Solution acti...

  • Page 52: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 46 of 128 errors 1000-1999 1413 'the spindle positioning speed cannot be zero' detection during execution. Cause the programmed positioning speed for function m19 is zero. Solution program a positioning speed greater than zero using the syntax: "s.Pos...

  • Page 53

    Cnc8070 r ef . 0402 e rror solutions page 47 of 128 errors 1000-1999 1425 'block skip is only admitted at the beginning of the line' detection during execution. Cause the "/" character is only admitted at the beginning of the program line. Solution check the program. 1426 'the pocket was resolved wi...

  • Page 54: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 48 of 128 errors 1000-1999 1434 'an associated slave axis could not be included in the configuration' detection during execution. Cause the instruction #call ax or #set ax has been used to include in the system configuration the master axis of an acti...

  • Page 55

    Cnc8070 r ef . 0402 e rror solutions page 49 of 128 errors 1000-1999 1444 'the main axes of the transformation must be linear' detection during execution. Cause one of the main three axes involved in the programmed transformation or kinematics is neither a linear axis nor a c axis. Solution the main...

  • Page 56: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 50 of 128 errors 1000-1999 1453 'axis name too long' detection during execution. Cause the axis name has more than two characters. Solution the valid axis names are: x, x1 … x9, y, y1, … y9, …, z, z1, … z9 a, a1 … a9, b, b1, … b9, …, c, c1, … c9 u, u1...

  • Page 57

    Cnc8070 r ef . 0402 e rror solutions page 51 of 128 errors 1000-1999 1464 'programmed rotary axis out of the range of the module' detection during execution. Cause the absolute coordinate (g90) programmed for the module type rotary axis is wrong. Solution the coordinate programmed for the axis must ...

  • Page 58: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 52 of 128 errors 1000-1999 1473 '#poly cannot be programmed while pattern rotation is active' detection during execution. Cause the #poly instruction has been programmed while the coordinate system rotation (g73) was active. Solution check the program...

  • Page 59

    Cnc8070 r ef . 0402 e rror solutions page 53 of 128 errors 1000-1999 1484 'signal number out of range' detection during execution. Cause the signal number programmed in the instruction #wait, #meet or #signal is wrong. Solution the signal programmed in the instructions #wait, #meet and #signal must ...

  • Page 60: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 54 of 128 errors 1000-1999 1493 '#spline on, g41/g42 and g136 cannot be programmed at the same time' detection during execution. Cause an attempt has been made to activate functions #spline on, g41, g42 and g136 at the same time at the cnc. Solution c...

  • Page 61

    Cnc8070 r ef . 0402 e rror solutions page 55 of 128 errors 1000-1999 1503 'the variable requires programming an axis' detection during execution. Cause an axis variable has been programmed, but no axis has been indicated for which to read or write a variable. Solution refer to the programming manual...

  • Page 62: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 56 of 128 errors 1000-1999 1510 'the axis does not exist or is not available in the channel' detection during execution. Cause the possible causes are: • an attempt has been made to move an axis that does not exist or is not available in the channel. ...

  • Page 63

    Cnc8070 r ef . 0402 e rror solutions page 57 of 128 errors 1000-1999 1518 'nr requires programming a movement in the block' detection during execution. Cause the repetition (nr) of a block has been programmed that does not involve a movement. Solution programming block repetition with nr is only val...

  • Page 64: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 58 of 128 errors 1000-1999 1527 'wrong identifier after %' detection during execution. Cause in the instruction #msg, #error or #warning , an invalid identifier has been programmed after "%". Solution the valid identifiers are: • to display a number: ...

  • Page 65

    Cnc8070 r ef . 0402 e rror solutions page 59 of 128 errors 1000-1999 1535 'program: #setsp [sp1, sp2, ..]' detection during execution. Cause the possible causes are: • the syntax of the instruction is wrong. • only the block number of a label may be programmed in the same block as the instruction. S...

  • Page 66: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 60 of 128 errors 1000-1999 1545 'spindle gear change is not possible while g63 or #cax is active' detection during execution. Cause the spindle gear change is not possible while tapping g63 is active or while working as c axis. Solution cancel g63 or ...

  • Page 67

    Cnc8070 r ef . 0402 e rror solutions page 61 of 128 errors 1000-1999 1553 'too many user variables' detection during execution. Cause the maximum number of user variables (v.P, v.S) that can be defined has been exceeded. Solution the maximum number of user variables that can be defined is 20. 1554 '...

  • Page 68: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 62 of 128 errors 1000-1999 1709 'drilling 1: p = 0' detection executing drilling cycle 1. Cause p (depth) programmed in the cycle equal to 0. Solution assign a value greater than 0. 1710 'drilling 2: f = 0' detection executing drilling cycle 2. Cause ...

  • Page 69

    Cnc8070 r ef . 0402 e rror solutions page 63 of 128 errors 1000-1999 1721 'reaming: t = 0' detection executing the reaming cycle. Cause no tool t has been programmed in the cycle. Solution assign a tool t. 1722 'reaming: p = 0' detection executing the reaming cycle. Cause p (depth) programmed in the...

  • Page 70: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 64 of 128 errors 1000-1999 1733 'boring 2: t = 0' detection executing boring cycle 1. Cause no tool t has been programmed in the cycle. Solution assign a tool t. 1734 'boring 2: p = 0' detection executing boring cycle 1. Cause p (depth) programmed in ...

  • Page 71

    Cnc8070 r ef . 0402 e rror solutions page 65 of 128 errors 1000-1999 1744 'pre-emptied pocket: t = 0' detection executing pre-emptied pocket cycle. Cause no tool t has been programmed in the cycle. Solution assign a roughing or finishing tool t. 1745 'pre-emptied pocket: p = 0' detection executing p...

  • Page 72: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 66 of 128 errors 1000-1999 1755 'rectangular boss :finishing tool diameter smaller than delta' detection executing rectangular boss cycle. Cause the diameter of the finishing tool is smaller than the finishing stock in the main plane (delta). Solution...

  • Page 73

    Cnc8070 r ef . 0402 e rror solutions page 67 of 128 errors 1000-1999 1766 'surface milling: p = 0' detection executing the surface milling cycle. Cause p (surface milling depth) programmed in the cycle equal to 0. Solution assign a value greater than 0. 1767 'surface milling: l = 0 and h = 0' detect...

  • Page 74: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 68 of 128 errors 1000-1999 1777 'profile: p = 0' detection executing the profiling cycle. Cause p (profile depth) programmed in the cycle equal to 0. Solution assign a value greater than 0. 1778 'profile: (finishing): tool's cutting length detection e...

  • Page 75

    Cnc8070 r ef . 0402 e rror solutions page 69 of 128 errors 1000-1999 1788 'circular pocket: s = 0' detection executing circular pocket cycle. Cause roughing or finishing s programmed in the cycle equal to 0. Solution assign a value greater than 0. 1789 'circular pocket: t = 0' detection executing ci...

  • Page 76: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 70 of 128 errors 1000-1999 1807 'g87: tool diameter = 0' detection executing a g87 pocket. Cause tool with radius 0. Solution modify the value of the tool radius in the tool table. 1808 'g87: tool missing' detection executing a g87 pocket. Cause tool ...

  • Page 77

    Cnc8070 r ef . 0402 e rror solutions page 71 of 128 errors 1000-1999 1818 'j = 0' detection executing a multiple machining cycle (g160-g165). Cause the j parameter (ordinate pass between machining operations) has been programmed with a 0 value in a multiple machining cycle. Solution assign a correct...

  • Page 78: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 72 of 128 errors 1000-1999 1828 '360 must be multiple of parameter i' detection executing a multiple machining cycle in circle (g163). Cause the angular pass (i) must be multiple of 360º. Solution assign a correct value to the cycle parameter. 1829 'i...

  • Page 79

    Cnc8070 r ef . 0402 e rror solutions page 73 of 128 errors 1000-1999 1839 'pocket with islands: wrong intersection of xy profiles' detection execution of a 2d or 3d pocket cycle with islands. Cause two xy profiles have at least some straight or arc section in common. Solution check that the intersec...

  • Page 80: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 74 of 128 errors 1000-1999 1849 'rectangular pocket: finishing stock delta greater than the pocket' detection executing a rectangular pocket. Cause the defined pocket cannot be executed because half the shorter length of the pocket minus the tool radi...

  • Page 81

    Cnc8070 r ef . 0402 e rror solutions page 75 of 128 errors 1000-1999 1860 'program k = 0/1/2' detection executing the #probe 3 cycle (surface measuring cycle). Cause parameter k only admits the values 0, 1, 2. Solution parameter k defines the axis to be used to measure the surface. Assign to k one o...

  • Page 82: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 76 of 128 errors 1000-1999 1870 'pocket with islands: wrong finishing s' detection execution of a 2d or 3d pocket cycle with islands. Cause the spindle speed (s) programmed for the finishing operation has a value of 0. Solution program s with a value ...

  • Page 83

    Cnc8070 r ef . 0402 e rror solutions page 77 of 128 errors 1000-1999 1880 'pocket with islands: semi-finishing t missing' detection execution of a 3d pocket cycle with islands. Cause the tool number (t) programmed in the semi-finishing operation does not exist in the tool table. Solution insert the ...

  • Page 84: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 78 of 128 errors 1000-1999.

  • Page 85: Errors 2000-2999

    Cnc8070 r ef . 0402 e rror solutions page 79 of 128 errors 2000-2999 errors 2000-2999 2000 'tool radius greater than the arc radius' detection during execution. Cause the tool radius is greater than the radius of the arc to be machined. Solution use a tool with a smaller radius. 2001 'profile damage...

  • Page 86: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 80 of 128 errors 2000-2999 2007 'while g138 is active, g40 is not allowed after the first compensation block' detection during execution. Cause tool radius cancellation (g40) has been programmed while the first compensation block is being processed in...

  • Page 87

    Cnc8070 r ef . 0402 e rror solutions page 81 of 128 errors 2000-2999 2101 'negative software limit overrun in g5-g60' detection during execution. Cause the path generated by the cnc to round the corner is out of the active travel limits. Solution program without g50 or g7 rounding . 2102 'programmin...

  • Page 88: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 82 of 128 errors 2000-2999 2116 'error when activating the spline' detection during execution. Cause an attempt has been made to activate a spline mode without canceling the previous one. Solution before activating it, cancel the previous one. 2118 's...

  • Page 89

    Cnc8070 r ef . 0402 e rror solutions page 83 of 128 errors 2000-2999 2129 'error in the rtcp transformation' detection during execution. Cause rtcp has been programmed, but the channel does not have all the axes needed for the transformation. Solution before activating the rtcp, configure the channe...

  • Page 90: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 84 of 128 errors 2000-2999 2141 'circular path not allowed (less than 2 axes)' detection during execution. Cause not possible if there aren't at least two axes in the channel. Solution configure the channel with at least two axes to be able to work wi...

  • Page 91: Errors 3000-3999

    Cnc8070 r ef . 0402 e rror solutions page 85 of 128 errors 3000-3999 errors 3000-3999 3000 'an arc cannot be programmed with a slave axis' detection during execution. Cause the possible causes are: 1. An attempt has been made to separately move an axis that is coupled to another axis. 2. An attempt ...

  • Page 92: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 86 of 128 errors 3000-3999 3011 'too many axis programmed as probe' detection when executing a probing block. Cause the number of axes programmed in the probing process exceeds the maximum number of axes of the channel. Solution modify the probing blo...

  • Page 93

    Cnc8070 r ef . 0402 e rror solutions page 87 of 128 errors 3000-3999 3025 'positive software travel limit overrun' detection during execution. Cause an attempt has been made to move an axis to coordinate that is beyond the software limits. The limits may have been set by machine parameter, via progr...

  • Page 94: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 88 of 128 errors 3000-3999 3036 'wrong gear change process' detection during execution. Cause the spindle gear in the cnc's history and the one indicated by the plc as being active are not the same. Solution check the plc program. 3037 'axis locked' d...

  • Page 95

    Cnc8070 r ef . 0402 e rror solutions page 89 of 128 errors 3000-3999 3504 'acceleration changing speed greater than the maximum' detection during startup or execution. Cause an acceleration changing speed greater than the maximum has been programmed. Solution program a smaller value than the maximum...

  • Page 96: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 90 of 128 errors 3000-3999 3606 'the spindle positioning requires an absolute coordinate' detection during execution. Cause after a spindle turn in open loop, the positioning must always be in absolute coordinates. Solution program the positioning in ...

  • Page 97

    Cnc8070 r ef . 0402 e rror solutions page 91 of 128 errors 3000-3999 3709 'error when refreshing analog inputs' detection when reading analog inputs. Cause failure in the cyclic reading process for analog intputs. This could probably be due to problems in the compci, can bus, analog input module, et...

  • Page 98: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 92 of 128 errors 3000-3999 3807 'incremental jog index out of range (switch positions 1-5)' detection during execution. Cause an attempt has been made to set via plc an incremental jog position that is out of the permitted range. Solution check the wr...

  • Page 99: Errors 4000-4999

    Cnc8070 r ef . 0402 e rror solutions page 93 of 128 errors 4000-4999 errors 4000-4999 4000 'error when initializing the sercos ring' cause failed sercos ring initializing process due to fiber optics connection problems, wrong cnc and drive parameter settings, problems on sercos or drive boards, etc....

  • Page 100: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 94 of 128 errors 4000-4999 wrong value 1 pdu code received with an error (must be 5). Wrong value 2 sercos drive error code: 30 error when changing to phase 3. 31 phase 4 command error. 32 error when changing to phase 4. 33 error when reading class di...

  • Page 101

    Cnc8070 r ef . 0402 e rror solutions page 95 of 128 errors 4000-4999 wrong value 2+3 other sercos drive error codes. Solution check the following: • analyze the error codes to try to determine the error source. • verify that the optical fiber is properly connected and in good condition. • check the ...

  • Page 102: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 96 of 128 errors 4000-4999 4203 'speed enable (spena) missing' cause while moving an axis, the spena signal (enable) of the plc drops. Solution analyze the plc maneuver to determine what causes the spena signal to drop. 4204 'error when resetting the ...

  • Page 103: Errors 5000-5999

    Cnc8070 r ef . 0402 e rror solutions page 97 of 128 errors 5000-5999 errors 5000-5999 5000 'plc error: the timer does not exist' detection plc timer data reading processes. Cause request to read a timer that does not exist. Solution valid timers: t1 - t256. 5001 'plc error: the counter does not exis...

  • Page 104: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 98 of 128 errors 5000-5999 5009 'syntax error when reading the variable from the plc' detection when executing cncrd instructions. Cause the variable does not exist or it does not have reading permission. Solution check the syntax of the variable to b...

  • Page 105: Errors 6000-6999

    Cnc8070 r ef . 0402 e rror solutions page 99 of 128 errors 6000-6999 errors 6000-6999 6000 'feedback alarm' detection during execution. Cause feedback error on analog axes. It is enabled by means of machine parameter fbackal. Differential ttl: • one or more cables broken (a, b signals or their inver...

  • Page 106: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 100 of 128 errors 6000-6999 6006 'one or several can nodes do not respond' cause one or several remote nodes do not respond due to a reset, shortcircuit, poor performance, etc. Solution see if all the modules are recognized in diagnosis mode. Contact ...

  • Page 107

    Cnc8070 r ef . 0402 e rror solutions page 101 of 128 errors 6000-6999 6013 'timeout when initializing the can' detection during startup. Cause failed initialization of the bus can due to bus problems. Off/on sequence too fast. Solution make the following checks and take the following actions to assu...

  • Page 108: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 102 of 128 errors 6000-6999 6020 'can cycle overlap' cause failed reading of digital and analog inputs, counters and keyboard handwheels. A node did not send the message in time. Solution verify in diagnosis mode that all the modules and the can error...

  • Page 109

    Cnc8070 r ef . 0402 e rror solutions page 103 of 128 errors 6000-6999 6029 'position increment limit exceeded at the cnc' cause excessive position increment of an analog axis. Hardware failure at the counter node, accesses to the compci (connections), etc. Solution contact our technical service depa...

  • Page 110: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 104 of 128 errors 6000-6999.

  • Page 111: Errors 7000-7999

    Cnc8070 r ef . 0402 e rror solutions page 105 of 128 errors 7000-7999 errors 7000-7999 7001 'two consecutive t's in cyclic magazine (m6 required)' detection during execution. Cause cyclic magazine and two consecutive t's have been programmed. Solution program an m6 after each t. 7002 'the tool is no...

  • Page 112: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 106 of 128 errors 7000-7999 7009 'in load mode: m6 without t' detection during execution. Cause in load mode, an m6 has been programmed without the corresponding t. Solution first, program a t with the tool to be loaded. 7010 'in load mode: t with two...

  • Page 113

    Cnc8070 r ef . 0402 e rror solutions page 107 of 128 errors 7000-7999 7020 'in setting: d required' detection during execution. Cause in setting mode, the edge of the tool must be specified. Solution program the edge. 7021 'in setting: d alone not allowed' detection during execution. Cause a "d" can...

  • Page 114: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 108 of 128 errors 7000-7999 7030 m6 without t' detection during execution. Cause an m6 has been detected without its corresponding t. If parameter "m6 alone = no", an error is issued. Solution m6 cannot be programmed without the corresponding t. 7031 ...

  • Page 115

    Cnc8070 r ef . 0402 e rror solutions page 109 of 128 errors 7000-7999 7041 'no tool is active' detection during execution. Cause an edge has been programmed, but there is no active tool in the spindle. Solution place a tool in the spindle. 7042 'pos has been programmed and the magazine is not in loa...

  • Page 116: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 110 of 128 errors 7000-7999.

  • Page 117: Errors 8000-8999

    Cnc8070 r ef . 0402 e rror solutions page 111 of 128 errors 8000-8999 errors 8000-8999 8200 'lexer fault when recognizing integers' detection during editing and execution in mdi. Cause an error has occurred when converting a string of characters into a numerical value. It usually occurs because some...

  • Page 118: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 112 of 128 errors 8000-8999 8209 'wrong active axis' detection during editing. Cause the axis name has been programmed with the wrong wild character. Solution the names of the axis with wild character are @1 through @5. 8210 'integer limits exceeded' ...

  • Page 119

    Cnc8070 r ef . 0402 e rror solutions page 113 of 128 errors 8000-8999 8225 'g function out of range' detection during editing and execution in mdi. Cause the programmed g function does not exist. Solution check the existing m functions in the programming manual. 8226 'h function out of range' detect...

  • Page 120: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 114 of 128 errors 8000-8999 8239 '"y" programmed twice' detection during editing. Cause the y axis has been programmed more than once in the block. Solution program the y axis only once in the block. 8240 '"z" programmed twice' detection during editin...

  • Page 121

    Cnc8070 r ef . 0402 e rror solutions page 115 of 128 errors 8000-8999 8254 'too many axes in g20' detection during editing. Cause some of the parameters programmed for g20 are not allowed. Solution check the g20 programming syntax. 8256 'nonexistent interpolator cycle instruction' detection during e...

  • Page 122: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 116 of 128 errors 8000-8999 8279 'mirror image repeated' detection during editing. Cause the possible causes are: 1. Function g11, g12 or g13 has been programmed more than one in the same block. 2. Functions g10 and g11, g12 or g13 have been programme...

  • Page 123

    Cnc8070 r ef . 0402 e rror solutions page 117 of 128 errors 8000-8999 8297 'parameter repeated' detection during editing. Cause the possible causes are: 1. The parameter conterror has been programmed more than once in the #hsc instruction. 2. In the subroutine calling instruction #pcall, #mcall or g...

  • Page 124: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 118 of 128 errors 8000-8999 8309 'too many axes have been programmed' detection during editing. Cause too many axes have been programmed in the #poly instruction. Solution the maximum number of axes that can be programmed is 3. 8310 'required paramete...

  • Page 125

    Cnc8070 r ef . 0402 e rror solutions page 119 of 128 errors 8000-8999 8318 'only one active axis 1 allowed per block' detection during editing. Cause the @1 axis has been programmed more than once in the block. Solution program @1 only once in the block. 8319 'only one active axis 2 allowed per bloc...

  • Page 126: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 120 of 128 errors 8000-8999 8402 'wrong tool magazine number' detection during editing. Cause the magazine number for which the variable of the tool manager is requested is wrong. Solution the magazine number must be between 1 and 4. If the magazine n...

  • Page 127: Tool and Tool Magazine Table

    Cnc8070 r ef . 0402 e rror solutions page 121 of 128 tool and tool magazine table tool and tool magazine table ‘the tool cannot be loaded into position %1’ detection during the manual loading of a tool from this dialog box, from the magazine list or loading the magazine table. Cause the tool does no...

  • Page 128: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 122 of 128 tool and tool magazine table ‘error when renaming the tool’ detection when trying to change the tool name. Cause it cannot create the tool in the database (bd8070.Mdb). The data base may be being used by another application or it may not ha...

  • Page 129

    Cnc8070 r ef . 0402 e rror solutions page 123 of 128 tool and tool magazine table ‘error opening file %1’ detection when loading, saving or printing the tool table or magazine table. Cause the possible causes are: 1. When loading a table. The data file does not exist, it does not have read permissio...

  • Page 130: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 124 of 128 tool and tool magazine table.

  • Page 131: Messages of The Profile

    Cnc8070 r ef . 0402 e rror solutions page 125 of 128 messages of the profile editor messages of the profile editor ‘unresolved profile’ cause the profile to be saved is not resolved completely either when “finishing” or when “saving and continuing” solution resolve the profile to be saved. Only reso...

  • Page 132: 128

    Cnc8070 r ef . 0402 of 128 e rror solutions page 126 of 128 messages of the profile editor ‘error in the axis of the plane’ cause some axis of the plane is wrong. The same axis has been placed in the “configuration” of the plane or some axis of the selected profile is not defined at the cnc. Solutio...

  • Page 133

    Cnc8070 r ef . 0402 e rror solutions page 127 of 128.

  • Page 134

    Cnc8070 r ef . 0402 e rror solutions page 128 of 128.