1. DL manuals
  2. Fagor
  3. Dishwasher
  4. LFU-45IT
  5. User Instructions

Fagor LFU-45IT User Instructions

Summary of LFU-45IT

  • Page 1

    Contents 27 1. Description of the controls________________________________ 28 2. Troubleshooting _______________________________________ 36 thank you for choosing one of our products. You are advised to read this manual carefully; it contains all the information you need about the right conditions f...

  • Page 2

    User instructions 28 1. Description of the controls 1.1 upper panel all the dishwasher controls are grouped on the upper panel. Switch-on, programming, switch-off etc. Procedures are only possible when the door is open. 1 on/off button pressing this button energises the appliance. 2 selected program...

  • Page 3

    User instructions 29 setting the washing program and switching on to select the most suitable program for the dishes to be washed refer to the table below, which indicates the most appropriate program according to dish type and degree of soiling. After using the table to identify the most appropriat...

  • Page 4

    User instructions 30 only run the soak program with half loads. To execute programs 6,7,8,9,10 users must first press the extra programs button (6). (*) reference program as per en 50242 standard. (1) average power consumption with the softener set on level 2. (2) the cycle duration and power consum...

  • Page 5

    User instructions 31 table for certification bodies reference standard en 50242 reference program eco load 10 place-settings type of detergent b amount of detergent 25 g rinse aid setting 5/6 1.2 washing programs before starting a washing program make sure that: • the water supply tap is open. • the...

  • Page 6

    User instructions 32 delaying the program the program delay button (8) can be pressed to delay the start of the program by up to 9 hours. This means that the dishwasher can be operated at the time of day of your choice. Press the button several times in succession and the display will show the delay...

  • Page 7

    User instructions 33 to save on energy! … and protect the environment • always try to run the dishwasher fully loaded. • do not wash the dishes in running water. • use the washing program that is most appropriate for each type of load. • do not carry out any preliminary rinsing. • if available, conn...

  • Page 8

    User instructions 34 adjusting the water softening system n.B.: for the setting below to be possible, a washing program other than the soak program must be set. Press the program delay button (8) and keep it pressed until the preset value appears followed by a full stop (normally 3.). Release the bu...

  • Page 9

    35 end of cycle at the end of the program the beeper sounds briefly and the lights of programs 4 and 5 flash (the word "end" is displayed on the window). To switch off the dishwasher, open the door and press the on/off button (1). Removing the dishes at the end of the washing program, wait at least ...

  • Page 10

    36 2. Troubleshooting the dishwasher is capable of signalling a number of faults through the simultaneous illumination of several indicator lights, with the following meanings: fault description e1 acquastop failure the anti-flooding system has been activated (for the relevant models only). The syst...

  • Page 11

    37 if an alarm occurs the appliance interrupts the program in progress and signals a fault. • alarms e1, e3, e4 interrupt the current program immediately. • the e5, e6 alarms interrupts the running program once the cause is resolved, it will bring bach the execution of the program. To “reset” an ala...

  • Page 12

    19 570 0050 00 3/4” 3/4” 1/2” sw32 min 40cm cu ø10 1 2 3 4 5 7 8 9 10 11 6 1 2 8 9 12 attenzione: quota : secondo i modelli 820÷870 oppure 820÷890. Depending on the model, distance may be 820÷870 or 820÷890. Cote : selon les modèles 820÷870 ou 820÷890. Maß : gemäß denmodellen 820÷870 oder 820÷890. H...