1. DL manuals
  2. Fairbanks
  3. Scales
  4. SCB-R9050 Series
  5. Operator's Manual

Fairbanks SCB-R9050 Series Operator's Manual

Manual is about: 21 x 21 Bench Scale

Summary of SCB-R9050 Series

  • Page 1

     2011-2015 by fairbanks scales, inc. 51244 all rights reserved revision 5 -- 04/15 ultegra max scb-r9050 series 21 x 21 bench scale operator manual.

  • Page 3: Amendment Record

    Amendment record ultegra max 21 x 21 bench scale scb-r9050 series document 51244 manufactured by fairbanks scales inc. 821 locust kansas city, missouri 64106 created 06/2010 revision 1 06/2010 released manual revision 2 01/2011 revised for 21” x 21” ultegra max model revision 3 07/2013 corrected acc...

  • Page 4: Disclaimer

    Disclaimer every effort has been made to provide complete and accurate information in this manual. However, although this manual may include a specifically identified warranty notice for the product, fairbanks scales makes no representations or warranties with respect to the contents of this manual,...

  • Page 5

    04/2015 5 51244 -- rev. 5 table of contents table of contents ............................................................................................. 5 section 1: general information .................................................................. 7 1.1. Introduction ...........................

  • Page 6

    04/2015 6 51244 -- rev. 5.

  • Page 7

    Section 5: specifications 04/2015 7 51244 -- rev. 5 section 1: general information 1.1. Introduction the scb-r9050 series bench scale is a usb powered unit with a capacity of 250 lbs and is constructed of steel. The scale may be placed on a desk, or a bench. Units may be ordered with an optional rol...

  • Page 8

    04/2015 8 51244 -- rev. 5 section 2: installation 2.1. Unpacking 1.Remove the scale from the packing box and place on a flat surface where it will be used. 2.Using the bubble level, adjust one or two feet minimally to level the platform. Do not adjust all 4 feet. 2.2. Connections 1. Usb - to use the...

  • Page 9

    Section 2: installation 04/2015 9 51244 -- rev. 5 2.3. Computer connections 1. Usb setup: the usb port will only function with a computer utilizing windows 2000, windows xp, or higher operating system. When the scale- connected usb cable is interfaced to a computer’s usb port or usb hub, the compute...

  • Page 10

    Section 2: installation 04/2015 10 51244 -- rev. 5 1. The display will show gru x. This is the gravity use zone. Select the proper zone number for your location. Use the [ units ] key to toggle to the selection. The choices are: -8, -7, -6, -5, -4, -3, -2, -1, 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10 press ...

  • Page 11

    04/2015 11 51244 -- rev. 5 section 3: operation 3.1. Power-on because the scale uses special low-power circuitry, no warm-up time is required. Weight readings will be accurate as soon as the unit is powered on and set to zero. When the unit is powered, the liquid crystal display (lcd) will show the ...

  • Page 12

    Section 3: operation 04/2015 12 51244 -- rev. 5 3.3. Weighing 1. With the platform empty, press the [zero] key. The display will indicate zero (0). Note: the “c” to the left of the “0.00” indicates true center of zero. 2. Check that the correct units are indicated; press the [units] key to change to...

  • Page 13

    04/2015 13 51244 -- rev. 5 section 4: customer care 4.1. Cleaning clean by wiping the scale assembly off with a damp cloth only. Do not use running water, harsh chemicals, or allow liquids to drip onto the scale/ display. 4.2. Operator instrument prompts prompt description hicap applied load is grea...

  • Page 14

    Section 4: customer care 04/2015 14 51244 -- rev. 5 4.3. Troubleshooting in the event the scale does not function properly, check the following, see appendix for more information: problem possible source / remedy no display power off, plug disconnected, cord damage, faulty usb port or usb to ac adap...

  • Page 15

    04/2015 15 51244 -- rev. 5 section 5: specifications 5.1. Technical specifications 1. Capacities: 250 lb/113 kg factory set 2. Rounding: nearest division per nist h-44 3. Weight display: .50 inch lcd display 4. Power on lockout: scale will display "------", when power is turned on and weight is pres...

  • Page 16

    Section 5: specifications 04/2015 16 51244 -- rev. 5 5.2. Environment all equipment should be protected from direct sunlight. • relative humidity 0% to 90% non-condensing. • not suitable for water wash down. 5.3. Accessories 1. Remote display 29595c - (acc-1520-1) 6.98"w x 3.48"h, 1.29”d, rj45 cable...

  • Page 17

    Ultegra max 21 x 21 bench scale document 51244 manufactured by fairbanks scales, inc . 821 locust street kansas city, mo 64106 www.Fairbanks.Com.