FALK LUX 22+23 Quick Start Manual - page 2
DeVICe DeSCRIPTIon
InITIaL SeTTInGS
oUTDooR naVIGaTIon VIeW
FITTInG To bICYCLe – PRoCeDURe
GeTTInG STaRTeD
IMPoRTanT InFoRMaTIon
RoUTe oPTIonS
DeSTInaTIon enTRY
SaVe PoSITIon
1. Screws
To attach to the stem, undo the screws, rotate the bracket
trough by 90 degrees and screw it tight again.
2. Place bracket onto the handlebar or stem.
3. Locking lever
Insert the studs on the side of the locking lever into the bracket,
but do not close the lever.
4. Adjusting lever
Pull the adjusting lever up to open it, press down to close and
thus fix the strap at the desired length and lock it in place.
5. Textile strap
Attach the textile strap on the inside by pulling it to the correct
length for the handlebar or stem. Make sure when you do this
that the textile strap is pulled tight so that the strap is taut
around the handlebar/stem. Close the adjusting lever.
IMPoRTanT: Press any protruding textile
strap fully into the bracket so that it does
not get in the way of or block the locking
lever which is subsequently locked in place.
6. Locking lever
Close the locking lever and lock it in place.
The textile strap must be made taut by this.
On/Off
Switches the device on.
If „On/Off“ is pressed during use, the following
options are available:
Keylock
Activates or disables the display lock
Screen
Switches off the display to save power. However,
ongoing navigations and track recordings remain active.
Stand-By
Switches to stand-by mode.
Switch off
Switches the device off completely.
Settings
For changing the volume and brightness
Control key
Starts and pauses the track recording
Opening the battery compartment:
On/Off
Screen/Display
battery compartment
Settings
USB port
microSD-card
3
2
1
Release lever
Screws
Adjusting lever
Textile strap
Locking lever
Control key
Slide the device into the bracket from the front and make sure
that it is inserted correctly into the guide rails at the side of
the bracket. The device can be heard to lock in place in the
bracket. To release the device from the bracket, press the
release lever down and slide the device out of the bracket.
Make sure you observe the following safety instructions in order to prevent accidents or
serious injuries:
This navigation device for
outdoor use is merely an orientation and navigation
aid which cannot be a substitute for making a sensible assessment of the situation
you are in. Please in any event note the particular characteristics of the terrain
and the routes you are using. Do not follow any routes or suggested routes which
would entail a dangerous or illegal form of riding or would place you in a dangerous
situation.
The
road traffic regulations must be complied with at all times, for example
when cycling, and have priority over the routes of the navigation device.
Never operate the navigation device while riding and do not allow yourself
to be
distracted by the device while riding.
Please note that United Navigation does not accept any
liability for any damage
caused by the device/bracket becoming detached from the bicycle.
The
map data which is used may include inaccurate or incomplete data. You
should therefore check the calculated route to see if it makes sense and choose
your own alternative route if necessary.
CaUTIon:
The navigation device is
not suitable for use as a vehicle navigation system!
Battery notes:
Do not use any sharp objects to remove the batteries.
Do not attempt to open the batteries.
Note the statutory regulations governing the disposal of the batteries.
The batteries which are supplied are not rechargeable batteries,
so do not attempt to recharge them.
Operating temperature: The maximum operating temperature is -10°C to 60°C.
Insert the batteries: To open the battery cover, turn
the silver fastener anticlockwise and pull it up so that
the cover of the battery compartment is removed.
Insert the batteries and make sure that
the poles are
aligned correctly. Place the battery cover back on
and close it by turning the silver fastener clockwise.
Now switch on your navigation device. Depending on
which type of battery you are using, you must select
the battery type under „Settings > System/General >
battery type“. This is important to adapt the device
optimally to the battery type and thus to achieve the
maximum run time from the battery.
IMPoRTanT noTe on baTTeRIeS:
You can use alkaline, lithium batteries or rechargeable NiMH batteries of the AA type.
Please note that rechargeable batteries
cannot be charged up in the device, not
even if you use a mains charger cable. Excessively high lighting of the display (e.g.
over 50%) will reduce the run time of the batteries. Batteries are very sensitive to
temperature. In cold conditions, the run time of the batteries is therefore greatly cur-
tailed. Optimum results are achieved at around 20°C. If the battery is weak, the screen
is dimmed and the loudspeaker output is reduced. To ensure
the longest possible
battery run time, beep output is recommended. When using rechargeable batteries,
please follow the manufacturer‘s instructions on use to ensure the maximum capacity
of the rechargeable batteries.
Create your own individual route by adjusting the route options to your needs. You can
set the route options after every destination entry.
Or you tap on the main menu on „Settings > Route Options“.
First select the
means of transport (bicycle or pedestrian).
Tap on
„next“.
Now specify
the type of route:
Easy
gives preference to routes with inclines of 0-4%
Sporty
gives preference to routes with inclines of 4-8%
Short
calculates the shortest route to the destination,
regardless of inclines
Linear distance shows a straight line towards the destination starting
from your current position
Tap on „Next“.
Choose the modes of
transport that you want to use, prefer or avoid on the route, for
example steep gradients, via ferrata or hiking trails.
Confirm your selection with „Done“.
After the route calculation, you have the following options:
Calculates two alternative routes
Change the route options
Shows the altitude profile
Shows information
for the calculated route
about the route
Via „Bus&Train“ you can have a Bus&Train connection calculated.
„Navigation“ starts the routing.
On the main menu select „Destination Entry >
Address“.
You can use the keypad which is shown to enter first
the city, then the street and street number.
Confirm your entry for city, street and street number
in each case by clicking on the right arrow and
then on the „OK tick“ to start the route calculation.
Alternatively, when it comes to entering the street,
you can click on the middle button to be navigated
to the city centre or to the middle of the street when
entering the street number.
As well as entering an address,
other entry options
are available to you such as POIs, waypoints or
coordinates.
Do you want to find a specific location again at a
later date?
Then you can save this location as a waypoint.
This will allow you to navigate there again very
easily at a later date.
To do this, on the main menu choose „Save position“.
Enter a name and tap on the „OK tick“.
In outdoor mode, the position is saved as a waypoint.
You will find the waypoints on the main menu in the
„Waypoint Manager“.
Info field
Information about the calculated route.
Tap on the field to select other information.
Rapid access menu Offers faster access to specific functions.
Click on map: If you tap on a point on the map, the point is marked with a pin and the
address or position is displayed.
If you tap on „Actions“, you could for example navigate to the marked point or save the
position.
1. Start the device.
2. Select the
language you want.
3. Select the
country map you want.
4. Acknowledge the note on
calibration of the
sensors by clicking on the „OK tick“.
5. Enter your
home address. You could then select
this at a later date with just one click to be
navigated back home directly. You can change
the address which is entered at any time via
„Settings > System/General > Set Home“.
6. Switch to the
main menu.
7. Carry out the calibration of the compass via
„Settings > System/General > Calibrate
Compass“
and follow the instructions of the device. You must
repeat the calibration when the compass needle is
shown in grey in the title bar of the map view.
8. Carry out the calibration of the barometer via „Settings > System/General > Calib-
rate Compass“ and follow the instructions of the device. Please note that, to obtain
optimum values, you should carry out the calibration process again before each
walk/bike ride.
Mode of transport
GPS signal quality
Info field
Battery status
Info field
Next street
Map
Compass
Zoom button
Position
Next
manoeuvre
Next-but-one
manoeuvre
Main menu
Altitude profile
Current street
Rapid access menu