Owner’s manual read and save these instructions model no. Fp810** the air shadow ™ glass bowl ceiling fan net weight 17.24 kg (38 lbs) warning: support directly from building structure for canada, this fan must be secured directly to the building structure or ceiling joist. Don’t secure this fan to ...
1. Limited lifetime motor warranty - if any part of your fan motor fails, due to a defect in materials or workmanship during the lifetime of the original purchaser, fanimation will provide the replacement part free of charge, when the defective fan is returned to our national service center. Proof o...
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be...
Clevis pin setscrew (2) 4 electrical and structural requirements ceiling ceiling joists 2˝ x 4˝ outlet box figure 1 how to assemble your ceiling fan pin setscrew hanger ball figure 1 1. Prior to assembly, set aside and save the hardware bag(s) packed in the packing. 2. Remove the hanger ball by loos...
5 how to assemble your ceiling fan (cont’d) 6. Route wires through opening in motor coupling cover. Position motor coupling cover on fan shown with open side facing down. (figure 2) 7. Route wires through opening in canopy. Position canopy on fan shown with open side facing up. (figure 3) 8. Reinsta...
6 how to hang your ceiling fan figure 1 floor no less than 7 ft ceiling joist wood member (2˝ x 4˝ approx.) figure 2 junction box ceiling support cable hanger bracket ceiling figure 3 downrod/hanger ball assembly attach safety cable to ceiling support cable tab note: supply wires and fan wires omitt...
7 blk-ant bl-ac in l wh-ac in n gray-reverse module blk-to motor l wh-to motor n grn or bare ground grn from hanger ball grn from bracket 120 vac supply (user supplied) blue-for light down how to wire your ceiling fan - c28 remote control if you feel that you do not have enough electrical wiring kno...
8 installing the canopy housing 1. Screw in two threaded rods into the hanger bracket (figure 1a). Note: the threaded rods in the hanger bracket serve as guides for easier installation. 2. Securely attach the canopy housing to the hanger bracket using the external lockwashers and knurled knobs suppl...
9 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connections...
10 installing the lk810** ▲warning to avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician. Caution turning off wall switch is not sufficent. To avoid possible electrical shock, be ...
11 installing the lk810** (cont’d) figure 5 figure 6 figure 7 5. Install light fixture to adapter with 3 screws provided. 6. Install five-60 watt candelabra bulbs (not included). 7. Assemble and install glass bowl with rubber washer, and finial nut, do not over-tighten. Installation note heavy! Requ...
12 parts list model #fp810** before discarding packaging materials, be certain all parts have been removed ref. # description part # retractable fan assembly – glass bowl fp810 ¾¾ fan motor assembly — mar20cy 5 retractable fan motor assembly — 10 control receiver reccan57demo 11 remote control c28 s...
13 note: the illustration shown is not to scale or its actual confi guration may vary the air shadow fan fp810** exploded-view 4 1 figure 1 3 6 5 2 7 8 8 ref 10 11 8 9.
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2007 fanimation 2007/01.
