Owner’s manual read and save these instructions model no. Fp825** the air shadow ™ traditional ceiling fan net weight 12.47 kg (27.5 lbs) warning: support directly from building structure for canada, this fan must be secured directly to the building structure or ceiling joist. Don’t secure this fan ...
1. Limited lifetime motor warranty - if any part of your fan motor fails, due to a defect in materials or workmanship during the lifetime of the original purchaser, fanimation will provide the replacement part free of charge, when the defective fan is returned to our national service center. Proof o...
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be...
Clevis pin setscrew (2) 4 electrical and structural requirements ceiling ceiling joists 2˝ x 4˝ outlet box figure 1 how to assemble your ceiling fan pin setscrew hanger ball figure 1 1. Prior to assembly, set aside and save the hardware bag(s) packed in the packing. 2. Remove the hanger ball by loos...
5 how to assemble your ceiling fan (cont’d) 6. Route wires through opening in motor coupling cover. Position motor coupling cover on fan shown with open side facing down. (figure 2) 7. Route wires through opening in canopy. Position canopy on fan shown with open side facing up. (figure 3) 8. Reinsta...
6 how to hang your ceiling fan figure 1 floor no less than 7 ft ▲warning the fan must be hung with at least 7´ of clearance from floor to blades (figure 1) ▲warning the outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Hanger bracket must seat firmly against...
7 blk-ant bl-ac in l wh-ac in n gray-reverse module blk-to motor l wh-to motor n grn or bare ground grn from hanger ball grn from bracket 120 vac supply (user supplied) blue-for light down how to wire your ceiling fan - c28 remote control if you feel that you do not have enough electrical wiring kno...
8 installing the canopy housing 1. Screw in two threaded rods into the hanger bracket (figure 1a). Note: the threaded rods in the hanger bracket serve as guides for easier installation. 2. Securely attach the canopy housing to the hanger bracket using the external lockwashers and knurled knobs suppl...
9 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connections...
10 installing the lk825** ▲warning to avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician. 1. Locate accessory mounting plate on bottom of fan. Figure 1 figure 2 figure 3 figure 4 ...
11 installing the lk825** (cont’d) figure 5 figure 6 figure 7 figure 8 5. Install lower housing. 6. Install finial nut on end of nipple, do not over tighten. 7. Install glass shades (not included). 8. Install 60 watt med-base bulbs (not included)..
12 parts list model #fp825** before discarding packaging materials, be certain all parts have been removed ¾¾ insert finish codes (refer to fan model number located on downrod support) how to order parts contact your retail store for repair parts. When ordering repair parts, always give the followin...
13 note: the illustration shown is not to scale or its actual confi guration may vary the air shadow fan fp825** exploded-view 4 1 figure 1 3 6 5 2 7 8 8 ref 9 10 8 ref.
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2007 fanimation 2007/01.
