Owner’s manual read and save these instructions model no. Fp510 / 520 fan series model no. Fp580 motor series the bourbon street ® belt-driven ceiling fans warning: support directly from building structure long neck fp520 net weight 48 lbs (21.7 kg) short neck fp510 net weight 38 lbs (17.2 kg) motor...
Table of contents unpacking instructions and parts identifi cation (motor assembly) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 unpacking instructions and parts identifi cation (fan assembly) . . . . . . . . . . . . . . . . . . . . . . . . ...
3 this manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions and parts identifi cation for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps hav...
4 unpacking instructions and parts identifi cation (cont’d) lag bolts (3) & flat washers (3) wood blade holder set (for use with fp1018 blade set only) note: the illustration shown is not to scale or its actual confi guration may vary. Parts and packings subject to change without notice. Note: vario...
5 electrical and structural requirements wiring and control option the motor assembly unit can only be wired to standard “light“ switch for on/off operation. Optional lighting fitters and light kits are available, including a single bowl fixture with a maximum of 180 watts and a variety of four ligh...
6 how to hang and wire your ceiling fan mounting motor unit: 1. Mark mounting hole positions for the motor unit onto the ceiling or supporting member. 2. Drill 1 ⁄ 8 ˝ pilot holes into the plywood base or supporting member to prevent splitting or cracking. While supporting the motor assembly, screw ...
7 how to hang and wire your ceiling fan (cont’d) 4. Cut and strip lead wires. 5. Securely connect the white fan motor wire to the white supply (neutral) wire using wire connector supplied. Securely connect the black fan motor wire wire to the black supply wire using wire connector supplied. (figure ...
8 belt splicing instructions 1. Wrap the belting around the two pulleys that will be connected and overlap the belting as shown. Use the spring clamps provided to hold the belting in place temporarily. With the clamps remaining in the same place, grasp both ends of the belting and pull tight. The cl...
9 mounting the fan blades standard reversible wooden blades 1. Mount the wooden blades on the blade holder with three screws and three fiber washers. (figure 1) 2. Then mount the assembled blade/blade holder onto the flywheel, secure with flywheel screws. (figure 2) note: various optional blades are...
10 maintenance periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the finish. Abrasive and/or non-abrasive cleaning agents are not required and should be avoided to prevent damage to finish. Bl...
11 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
12 ref. # description qty part # bourbon street motor assembly 1 ' 1 switch cap assembly 2 ap58005 ¾ ¾ 2 screw, pan hd, 5 / 32 -32 x ¼˝ 6 ' 3 wiring harness 2 p5825 4 nut 2 ' 5 flat washer 2 ' 6 switch cap adapter 2 ' 7 motor pulley 2 ' 8 motor housing 1 p516 ¾ ¾ 9 m/s, washer hd, 8-32 x 3½˝, black ...
13 exploded-view the bourbon street ® motor pack fp580 note: the illustration shown is not to scale or its actual confi guration may vary. Wires partially removed for clarity. 1 3 2 4 7 5 6 10 11 13 14 12 8 figure 1 9 13, 14 ref 15 16 17 18 19 20
14 ref. # description qty part # short fan assembly 1 fp510 ¾ ¾ 1 switch cap 1 ap52005 ¾ ¾ 2 locknut, steel, 1/8˝ ips 1 ' 3 flat washer, 0.04˝ id x ¼˝ od 2 ' 4 switch cap adapter 1 p850bl 5 flywheel 1 p3250-65 6 short leg 3 p510 ¾ ¾ 7 collector 1 p514 ¾ ¾ 8 bearing, collector 1 brg202 9 flat washer,...
15 note: the illustration shown is not to scale or its actual confi guration may vary. Exploded-view the bourbon street ® fan pulley assembly pack fp510__ (short) 2 figure 2 3 15 14 16 11 9 10 3 14 9 7 12 8 5 4 1 6 13 17 18 10 9 13 20 19 (fastens under the fan base) (fastens under the fan base) 21 2...
16 before discarding packaging materials, be certain all parts have been removed ¾ insert finish codes (refer to fan model number located on fan assembly) ' non-sevicable items parts list fp520 fan pulley assembly - long ref. # description qty part # long fan assembly 1 fp520 ¾ ¾ 1 switch cap 1 ap52...
Note: the illustration shown is not to scale or its actual confi guration may vary. Exploded-view the bourbon street ® fan pulley assembly pack fp520__ (long) figure 3 2 3 5 4 1 10 9 7 8 8 10 9 11 9 14 16 17 15 3 14 6 13 (fastens under the fan base) 20 21 18 19 25 24 20, 21 ref 22 23 17 3 12.
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2007 fanimation 2007/09.
