Owner’s manual read and save these instructions model no. Fp4220** the centaurus ® ceiling fan centaurus ® fan black finish shown with maple blade set centaurus ® fan satin nickel finish shown with cherry blade set net weight 15.28 kg (33.7 lbs).
Table of contents unpacking instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 electrical and structural requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be...
Clevis pin setscrew (2) 4 electrical and structural requirements your new ceiling fan will require a grounded electrical supply line of 120 volts ac, 60 hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 35 lbs. Figure 1 depicts different stru...
5 how to assemble your ceiling fan (cont’d) 6. Position assembled blade spacer on the blade as shown in (figure 3a). Fasten both ends of the spacer with supplied fasteners. Do not overtighten. (figure 3b) repeat step for other two blades. 7. Prior to mounting blades, position the three blade mount c...
6 how to hang your ceiling fan figure 1 floor ceiling no less than 7 ft ▲warning the fan must be hung with at least 7´ of clearance from floor to blades (figure 1) ▲warning the outlet box must be securely anchored and capable of withstanding a load of at least 35 lbs. Hanger bracket must seat fi rml...
Figure 1b figure 1a 9v battery remote transmitter unit detail reciever unit detail 7 how to wire your ceiling fan - c20 remote control operating instructions - c20 remote control 1. Operating & using remote transmitter (figure 3): install 9 volt battery (if not using for long periods of time, remove...
8 installing the canopy housing 1. Screw in two threaded rods into the hanger bracket (figure 1a). Note: the threaded rods in the hanger bracket serve as guides for easier installation. 2. Securely attach the canopy housing to the hanger bracket using the external lockwashers and knurled knobs suppl...
9 3. Securely attach plugs from motor to sockets on downlight socket plate assembly (figure 3) figure 3 installing the lower housing assembly (cont’d) figure 4 figure 5 4. Securely attach downlight socket plate assembly to the adapter plate by tightening three screws with spring washers ( 5 / 32 -32...
Maintenance blade cleaning periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the fi nish. Abrasive cleaning agents are not required and should be avoided to prevent damage to fi nish. Periodic...
11 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
12 before discarding packaging materials, be certain all parts have been removed parts list model #fp4220** ref. # description part # 1 hanger bracket assembly apg510bl 2 downrod/hanger ball assembly containing: adr6 ¾¾ 2a hanger ball assembly 2b downrod 2c hairpin clip 2d clevis pin 3 ceiling canop...
13 note: the illustration shown is not to scale or its actual confi guration may vary the centaurus ® fp4220** exploded-view 4 1 figure 1 3 2a 7 11 ref 6 5 11 9 2b 2c 2d 2 8 10 12.
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2007 fanimation 2007/08.
