Owner’s manual read and save these instructions model no. Fp2120** series the enigma ® ceiling fan suitable for use with solid state speed controls warning: support directly from building structure net weight 38 lbs. Or 17.3 kg. For canada, this fan must be secured directly to the building structure...
. Table of contents unpacking instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3 electrical and structural requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 how to...
3 this manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will ...
4 electrical and structural requirements your new ceiling fan will require a grounded electrical supply line of 120 volts ac, 60 hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 1 depicts different structural confi gurations t...
5 how to assemble your ceiling fan (cont’d) 6. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod. (figure 3a) remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in step 9. 7. S...
Junction box ceiling support cable ceiling joist wood member (2” x 4” approx.) hanger bracket ceiling downrod/hanger ball assembly attach safety cable to ceiling support cable tab note: supply wires and fan wires omitted for clarity ceiling floor ceiling no less than 7 ft blade radius 30˝ (60˝ blade...
Off hi lo med 9v battery remote transmitter unit detail reciever unit detail 9v battery receiver unit ceiling bracket (open end) note: receiver wires omitted for clarity. Blk-ant bl-ac in l wh-ac in n blue-for light down blk-to motor l wh-to motor n grn or bare ground grn from hanger ball grn from b...
8 installing the canopy housing 1. Screw in two threaded rods into the hanger bracket (figure 1a). Note:the threaded rods in the hanger bracket serves as guides for easier installation. 2. Securely attach the canopy housing to the hanger bracket using the external lockwashers and knurled knobs suppl...
9 maintenance periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the fi nish. Abrasive and/or non-abrasive cleaning agents are not required and should be avoided to prevent damage to fi nish. C...
10 ref. # description part # 1 hanger bracket apg610bl 5 ceiling canopy p2100 ¾¾ 2 downrod/hanger ball assembly containing: adr1x6 ¾¾ 2a hanger ball assembly 2b downrod 2c clevis pin 2d hairpin clip 3 ceiling canopy pg158 ¾¾ 4 motor coupling cover ap60030 ¾¾ 5 ceiling fan assembly ama2120 ¾¾ 6 lower...
2a 2b 2c 2d 2 8 7 6 4 5 3 9 1 10 11 note: the illustration shown is not to scale or its actual confi guration may vary. Wires partially removed for clarity. Exploded-view the enigma ® fp2120** figure 1.
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 visit our website @ www.Fanimation.Com copyright 2007 fanimation 2007/08.
