Owner’s manual read and save these instructions model no. Fp2320** the escalade ® ceiling fan suitable for use with solid state speed controls warning: support directly from building structure net weight 38 lbs. Or 17.3 kg..
. Table of contents unpacking instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 how to assemble your ceiling fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
U/l d/l fan off off on low med hi 3 this manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all s...
4 electrical and structural requirements wiring and control options please choose one of the following options and proceed to the page as indicated. 1. Standard 3-speed fan only, remote or wall control. 2. Fan (& optional light) remote control (c8), see page 7. 3. Fan (& optional light) wall control...
5 how to assemble your ceiling fan (cont’d) 4. Separate and untwist the two wires and the safety cable. Route the leads through the downrod. 5. Loosen the two setscrews in the downrod support. Align the clevis pin holes in the downrod with the holes in the downrod support. Install the clevis pin and...
6 how to hang your ceiling fan 1. Securely attach the ceiling support cable to the ceiling joist or structural member using the ⅜” x 2” lag bolt and fl at washer. The lag bolt will pass through the fl at washer, loop of the ceiling support cable, the outlet box and into the supporting member (figure...
7 how to wire your ceiling fan - c8 remote control operating instructions - c8 remote control if you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Figure 10 9v battery 1. Operating & using remote transmitter (figure 10)...
Off on u/l d/l fan o ff low med hi 8 how to wire and operate your c9 wall control 1. Setting the code: the remote unit has 16 different code combinations. It may be necessary to test a couple frequency code settings to improve signal reception and/or eliminate interference from other remote control ...
9 installing the canopy housing 1. Screw in two threaded rods into the hanger bracket (figure 15a). Note:the threaded rods in the hanger bracket serves as guides for easier installation. 2. Securely attach the canopy housing to the hanger bracket using the external lockwashers and knurled knobs supp...
10 maintenance figure 17 how to change your light bulbs screw (2) retaining ring ba15d bulb 1. Turn off power. 2. Remove the screws and the retaining ring. 3. Remove the burned-out bulb(s). By gently pressing down on the bulb, twisting counter-clockwise and pulling out the bulb (figure 17). 4. Firml...
11 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
Ref. No. Description part # 1 hanger bracket apg510bl 5 ceiling canopy pg160 ¾¾ 2 downrod/hanger ball assembly containing: adr6 ¾¾ 3 clevis pin 4 hairpin clip 7 motor coupling cover mcc ¾¾ fan motor assembly consisting of: fp2320 fan body ¾¾ 8 housing, upper p2370 ¾¾ 9 cover, light channel (6) p2330...
Note: the illustration shown is not to scale or its actual confi guration may vary. Wires partially removed for clarity. Exploded-view 19 18 20 27 24 8 10 11 12 13 15 16 7 6 4 5 22 3 17 2 ground wire (green) ground wire (green) the escalade ® fp2320** optional - sold separately 23 9 1 26 figure 18 2...
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 visit our website @ www.Fanimation.Com copyright 2007 fanimation 2007/01.
