Owner’s manual read and save these instructions model no. Fp10 / 20 fan series model no. Fp1280**-220 motor series the brewmaster ® belt-driven ceiling fans suitable for use with solid state speed controls warning: support directly from building structure long neck fp20 net weight 15 lbs (6.8 kg) sh...
Table of contents (motor assembly) unpacking instructions and parts identifi cation . . . . . . . . . . . . . . . . . . . . .3 (pulley assembly) unpacking instructions and parts identifi cation . . . . . . . . . . . . . . . . . . . .4 electrical and structural requirements . . . . . . . . . . . . . ...
3 this manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions and parts identifi cation for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps hav...
4 unpacking instructions and parts identifi cation (cont’d) lag bolts (4) & flat washers (4) wood blade holders (for use with fp1022, fp1026, fp1030 blade sets) traditional blade holders (for use with palm, bamboo, wicker blade sets) note: the illustration shown is not to scale or its actual confi g...
5 electrical and structural requirements lighting options optional lighting fi tters and light kits are available, including a single bowl fi xture with a maximum of 180 watts and a variety of four light fi xtures with a maximum of 240 watts. Can be only mounted on the motor switch cup. Installation...
6 how to hang and wire your ceiling fan 1. You will first drill ³⁄ 16 ˝ pilot holes into the plywood base or supporting member to prevent splitting or cracking. Mount the pulley assembly on the ceiling with 4 lag bolts and flat washers (figure 1a). 2. Drill ³⁄ 16 ˝ pilot hole located approximately a...
N l1 l how to hang and wire your ceiling fan (cont’d) 4. Mount retainer to junction box with screws (provided with your junction box). (figure 3) 5. Loosen strain relief and pull excess lead wires through canopy. Re-tighten strain relief. 6. Cut and strip lead wires. 7. Connect the yellow/green grou...
8 how to hang and wire your ceiling fan (cont’d) figure 6 junction box ceiling plywood base motor housing ceiling joist 2˝ lag bolt & flatwasher (4 places) 11. After the connections have been made, tighten the lag bolts to secure fan base assembly to the ceiling, making sure that the electrical wire...
9 belt splicing instructions 1. Wrap the belting around the two pulleys that will be connected and overlap the belting as shown. Use the spring clamps provided to hold the belting in place temporarily. With the clamps remaining in the same place, grasp both ends of the belting and pull tight. The cl...
Figure 2 mounting the fan blades natural palm leaf, woven bamboo, woven wicker blades 1. Lay side “a” of the blade holder on a fl at surface with the inside of the blade holder facing up. This is the side with the threaded posts and pitched foot (figure 1). 2. Position the palm leaf, or the woven ba...
11 maintenance periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the fi nish. Abrasive and/or non-abrasive cleaning agents are not required and should be avoided to prevent damage to fi nish. ...
12 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
13 17 exploded-view the brewmaster ® motor fp1280**-220 note: the illustration shown is not to scale or its actual confi guration may vary. Wires partially removed for clarity. 18 14 19 1 2 3 6 4 5 9 8 10 12 13 11 ref. # description part # brewmaster motor assembly fma1280 ¾ 1 switch cap assembly ps...
14 ref. # description part # pulley assembly fp10¾/fp20¾ 1 pulley with set screw ' 2a short frame (short model) ' 2b long frame (long model) ' 3 cushion, bearing, black ' 4 bearing ' 5 shaft ' 6 hub ' 7 blade holder (2) (wooden blades only) p1212¾ 8 bag, bh to hub screws,10-32 x ½˝,black (5) hdwfp10...
Note: the illustration shown is not to scale or its actual confi guration may vary. Exploded-view 8 the brewmaster ® pulley assembly pack fp10__ (short) / fp20__ (long) 15 7 11 6 5 3 4 2a 2b 1 3 4 14 9 8 9 10 11 12 13 10 figure 2 15.
10983 bennett parkway zionsville, in 46077 toll free (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2008 fanimation 2008/02.
