- DL manuals
- Fanimation
- Fan
- FP8050 The Quattro
- Owner's Manual
Fanimation FP8050 The Quattro Owner's Manual
Summary of FP8050 The Quattro
Page 1
Model no. Fp8050 ceiling fan owner's manual read and save these instructions net weight 7.3 kgs. (16.1 lbs.) the quattro ™.
Page 2
2 important safety instructions warning: to avoid fire, shock and serious personal injury, follow these instructions. 1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams. 2. Before servicing or cleaning unit, switch power off a...
Page 3
1. Check to see that you have received the following parts: note: if you are uncertain of part description, refer to exploded view illustration. This manual is designed to make it as easy as possible for you to assemble, install, operate and maintain your ceiling fan tools needed for assembly • one ...
Page 4
4 energy efficient use of ceiling fans ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure efficient product performance. Choosing the appropriate mounting location ceiling fans should be installed, or mounted, ...
Page 5
5 how to assemble your ceiling fan 1. Remove the hanger ball portion from the downrod/hangerball assembly by loosening the set screw in the hanger ball until the ball falls freely down the downrod. Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reins...
Page 6
The fan must be hung with at least 7' of clearance from floor to blades (figure 1). Warning 6 to avoid possible fire or shock, be sure electricity is turned off at the main fuse box before hanging. Warning 6. Cut off excess lead wire approximately 6 to 9 inches above top of the top of the downrod. S...
Page 7
7 how to wire your ceiling fan to avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging (figure 1). Warning ! Note: if you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must be grounded for safe operation...
Page 8
8 how to wire your ceiling fan (continued) check to see that all connections are tight, including ground, and that no bare wire is visible at the wire connectors except for the ground wire. Do not operate fan until the blades are in place. Noise and motor damage could result. Warning x 6 wire connec...
Page 9
9 how to assemble the blades and light kit x 16 x 16 fiber washer 3/16-24 x 12.5mm washer head screws hardware used: blade 3/16-24 x 12.5mm washer head screw and fiber washer (3 each per blade) figure 1 figure 2 motor assembly upper light kit plate figure 3 1. Slide blade through slot and secure usi...
Page 10
10 how to assemble the blades and light kit (continued) light bulb figure 4 figure 5 4. Insert light bulb and twist until light bulb terminals have seated properly in the gu10 socket. (figure 4) 5. Twist on lower light kit cover by aligning pin slots in upper light kit plate (figure 5). Kit cover lo...
Page 11: Maintenance
11 how to operate your ceiling fan (continued) 3. The 5-button hand-held remote transmitter includes five buttons for high, medium and low fan speeds as well as fan off and light on/off. Infinite light levels are available by holding the light on/off button (figure 3). Reverse switch figure 4 4. If ...
Page 12: Trouble Shooting
12 trouble shooting for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Warning ! Trouble probable cause suggested remedy 1.Fan will not start 1. Check main and branch circuit fuses or circuit breakers. 2. Check line wire connections to fan and switch ...
Page 13: Parts List
13 13 1 2 3 4 5 6 11 10 8 9 12 7 note: the illustration shown is not to scale or its actual configurations may vary. Part description part # fan motor assembly hanger bracket with screws hanger ball/downrod assembly ceiling canopy canopy screw cover motor coupling cover blade set upper light kit pla...
Page 14
Copyright fanimation 2010 2010/05 10983 bennett parkway zionsville, in 46077 toll free (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 fanimation visit our website www.Fanimation.Com.