1. DL manuals
  2. Fanimation
  3. Fan
  4. FPD8148AU Series
  5. Owner's Manual

Fanimation FPD8148AU Series Owner's Manual

Summary of FPD8148AU Series

  • Page 1

    Model no. Fpd8148**au owner's manual read and save these instructions ceiling fan net weight 14.6 kg the odyn ™.

  • Page 2

    Important safety instructions warning: to avoid fire, shock and serious personal injury, follow these instructions. 1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams. 2. Before servicing or cleaning unit, switch power off at ...

  • Page 3

    3 ‡)dq0rwru$vvhpeo\ ‡+dqjhu%udfnhw$vvhpeo\ ‡'rzqurg+dqjhu%doo$vvhpeo\ ‡&hlolqj&dqrs\ ‡&dqrs\6fuhz&ryhu$vvhpeo\ ‡0rwru&rxsolqj&ryhu$vvhpeo\ ‡%odgh&ryhu6hw ‡%odgh+roghu6hw ‡%odgh6hw ‡/ljkw3odwh$vvhpeo\ ‡/('*odvv$vvhpeo\ ‡$gdswhu6whho&ds6whho&ds$vvhpeo\ ‡*odvv ‡+dqg+hog5hprwh ‡ +dugzduhedjv – 7zhqw\hlj...

  • Page 4

    This new ceiling fan will require a grounded electrical supply line of 220-240 volts ac, 50 hz, 10 amp circuit. The hanger bracket must be securely anchored and capable of supporting a load of least 60kg. If your fan is to replace an existing ceiling light fixture, turn electricity off at the main f...

  • Page 5

    5 assembling this ceiling fan 1 . Remove the hanger ball portion from the downrod/ hanger ball assembly by loosening the set screw in the hanger ball until the ball falls freely down the downrod. Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinsta...

  • Page 6

    6 7. Cut off excess lead wire approximately 15 - 25 cm above top of the top of the downrod. Strip insulation off 10 mm from the end of each lead wire. (figure 7) note: all set screws must be checked, and retightened where necessary, before installation. 6. Reinstall the hanger ball on the downrod as...

  • Page 7

    How to hang this ceiling fan warning the fan must be hung with at least 2.1m of clearance from ƀ oor to blades. (figure 2) warning the hanger bracket must be securely mounted and capable of supporting at least 60 kg. If bracket and /or timber batten are not securely attached, the fan could wobble or...

  • Page 8

    How to wire your ceiling fan warning to avoid possible ſ re or shock, be sure electricity is turned off at the main fuse box before wiring. (figure 1) figure 1 main fuse box this ceiling fan must be installed by a licensed electrician. ʆ warning figure 2 8 terminal block (on hanger bracket) supply c...

  • Page 9

    9 installing the canopy housing 2. Securely attach and tighten the canopy screw cover over the shoulder screws in the hanger bracket utilizing the keyslot twist-lock feature. (figrue 2) 1. Remove one of the two shoulder screws in the hanger bracket. Loosen the second shoulder screw without fully rem...

  • Page 10

    Figure 2a 10 assembling the light kit assembly or cap 1 (option a--for use with light kit) remove one of the three screws in the support bracket at the bottom of the motor assembly. Slightly loosen the remaining two screws. Assemble the light plate assembly to the support bracket using the two key s...

  • Page 11

    Note: if you need to change the blades: turn the power off → change the blades → turn the powe r on → perform the control setting process again. Figure 3 3. Remote control setting and speed (rpm ) setting process : (figure 3) 1. When powering on your fan, do not press any button(s) before pressing t...

  • Page 12

    : controls light on/off button. 5. The receiver provides the following protective function: lock position: the dc motor has a built-in safety feature against blade obstruction during operation. If something obstructs the fan blades the motor will stop operating after 30 seconds of interruption. Plea...

  • Page 13

    13 trouble shooting for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Warning trouble probable cause suggested remedy 1.Fan will not start 1. Check main and branch circuit fuses or circuit breakers. 2. Check line wire connections to fan and switch wi...

  • Page 14

    Bag assembly safety cable — — before discarding packaging materials, be certain all parts have been removed how to order parts when ordering repair parts, always give the following information: for repair parts: phone 1300 469 326 www.Myfan.Com.Au ‡3duw1xpehu ‡3duw'hvfulswlrq ‡)dq0rgho1xpehu insert ...

  • Page 15

    15 model fpd8148**au exploded-view note: the illustration shown is not to scale or its actual con ¿ guration may vary. Product/parts are subject to change without notice. Figure 1 1 2 3 4 5 6 7 8 16 14 9 12 10 11 the odyn ™ 16 16 13 15.

  • Page 16: Myfan Warranty

    Myfan 36 month on-site warranty section 2: congratulations! By purchasing from an authorised partner or directly from myfan, your product is now covered by our 36 month on-site warranty. Should your fan fail within the first 36 months, due to a defect in materials or workmanship, myfan (at our sole ...

  • Page 17

    Copyright 2015 fanimation 2015/10 v.01 distributed in australia by myfan pty ltd www.Myfan.Com.Au.