Owner’s manual read and save these instructions models no. Hf7000, 7040, 7400 series decorative uplight fan net weight 15 kg (33 lbs) warning: support directly from building structure for canada, this fan must be secured directly to the building structure or ceiling joist. Don’t secure this fan to a...
1. Limited lifetime motor warranty - if any part of your fan motor fails, due to a defect in materials or workmanship during the lifetime of the original purchaser, fanimation will provide the replacement part free of charge, when the defective fan is returned to our national service center. Proof o...
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be...
Collar 4 electrical and structural requirements ceiling ceiling joists 2˝ x 4˝ outlet box figure 1 how to assemble your down rod sleeve collar (2) sleeve, 8˝ checkring figure 1 1. Prior to assembly, set aside and save the hardware bag(s) packed in the packing. 2. Check to see that you have received ...
2½˝ 5 how to assemble your down rod sleeve (cont’d) collar figure 3 dr1x12 12˝ down rod assembly: 3. Assemble two collars and 4˝ sleeve, as shown (figure 3). Collar figure 4 dr1x18 18˝ down rod assembly: 4. Assemble the 18˝ down rod and the sleeve kit in the order as shown (figure 4). Sleeve, 4˝ col...
6 clevis pin setscrew (2) how to assemble your ceiling fan pin setscrew hanger ball figure 1 1. Prior to assembly, set aside and save the hardware bag(s) packed in the packing. 2. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod. (figur...
7 how to assemble your ceiling fan (cont’d) 12. The fan comes with black and white leads. Before installing fan, measure up approximately 6-9 inches above top of downrod/hanger ball assembly. Cut off excess wire and strip back insulation ½˝ from end of wire. 13. You have now completed the assembly o...
8 how to hang your ceiling fan figure 1 floor no less than 7 ft ▲warning the fan must be hung with at least 7´ of clearance from floor to blades (figure 1) ▲warning the outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Hanger bracket must seat firmly against...
9 how to wire your ceiling fan - c22 remote control if you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Figure 1b figure 1a 9v battery remote transmitter unit detail receiver unit detail figure 2 fan motor unit bl-ac i...
Installing the canopy housing 1. Screw in two threaded rods into the hanger bracket (figure 1). Note: the threaded rods in the hanger bracket serve as guides for easier installation. 2. Securely attach the canopy housing to the hanger bracket using the external lock washers and knurled knobs supplie...
11 maintenance blade cleaning periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the fi nish. Abrasive cleaning agents are not required and should be avoided to prevent damage to fi nish. Perio...
12 parts list models #hf7000bz, #hf7040**, #hf7400ds before discarding packaging materials, be certain all parts have been removed ¾¾ insert finish codes (refer to fan model number located on downrod support) how to order parts contact your retail store for repair parts. When ordering repair parts, ...
13 note: the illustration shown is not to scale or its actual confi guration may vary decorative uplight fan hf7040** exploded-view (also for acharn™ & scroll fans) 4 1 figure 1 3 6 5 2 7 13 12 11 8 9 10
14 installing the acharn ™ light kit – lkhf7060bz ▲warning to avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician. 1. Remove the plug, lockwasher and nut from the bottom of switch ...
15 installing the acharn ™ light kit – lkhf7060bz (cont’d) figure 5 5. Reinstall the assembled switch cup cover & light kit using the two flat head screws supplied with your fan. Install one 100 watt medium base bulb (not included). Figure 6 6. Carefully hook the glass bowl onto three hooks on the l...
16 installing the scroll light kit – lkhf7460ds ▲warning to avoid fire or shock, follow all wiring instructions carefully. Any electrical work not described in these instructions should be done or approved by a licensed electrician. 1. Remove the plug, lockwasher and nut from the bottom of switch cu...
17 figure 5 5. Reinstall the assembled switch cup cover & light kit using the two flat head screws supplied with your fan. 6. Install the 3 glass shades with spacers and shade nuts provided. 7. Install three 60 watt medium base bulbs (not included). Restore power to the fan/light kit assembly. Insta...
Trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connections i...
Copyright 2008 fanimation 2008/01 h ubbardton f orge d esign , m anufactured and d istributed b y f animation 10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com all hubbardton forge designs, the mark hubb...
