1. DL manuals
  2. Fanimation
  3. Fan
  4. Old Havana FPH210
  5. Owner's Manual

Fanimation Old Havana FPH210 Owner's Manual

Other manuals for Old Havana FPH210: Specification Sheet
Manual is about: Old Havana Series

Summary of Old Havana FPH210

  • Page 1

    Motor as sem bly #fph210 weight 19 lbs motor ass'y with pedestal ac ces so ry weight 29 lbs motor ass'y with floor/desk accessory weight 25 lbs motor ass'y with wall accessory weight 27 lbs motor ass'y with ceiling fan ac ces so ry weight 22 lbs owner’s manual read and save these instructions series...

  • Page 2

    . 1. Limited lifetime motor warranty - if any part of your fan motor fails, due to a defect in materials or workmanship during the lifetime of the original purchaser, fanimation will provide the replacement part free of charge, when the defective fan is returned to our national service center. Proof...

  • Page 3

    This manual is designed to make it as easy as possible for you to as sem ble, install, operate, and maintain your fan the motor assembly you purchased is shipped in a separate carton. Follow the unpacking instructions below. After completely unpacking the motor assembly proceed to the proper section...

  • Page 4

    Tools needed for as sem bly • one phillips head screwdriver • one stepladder • one 1/4˝ blade screwdriver • one wire stripper • three wire connectors (supplied) • allen wrench (supplied) materials wiring outlet box and box con nec tors must be of type required by local code. The minimum wire would b...

  • Page 5

    How to assemble the ceiling accessory note: proceed to page 8 for assembly instructions if you have purchased a floor/desk model, page 10 for pedestal model assembly instructions and page 12 for wall mount model assembly instructions. Prior to assembly, set aside and save the hardware bag packed in ...

  • Page 6

    Note: the setscrews must be prop er ly in stalled as described above, or fan-wobble will result. 16. The fan comes with green, black, and white leads. Before installing fan, measure up approximately 6-9 inches above top of downrod/hanger ball assembly. Cut off excess wire and strip back insulation ½...

  • Page 7

    Electrical and structural requirements how to hang your ceiling fan 1. Securely attach the hanger bracket to the outlet box using the outlet box screws and washers supplied with your fan or outlet box (fig. 7). 2. Pull the electric wires in the outlet box down through the opening in the hanger brack...

  • Page 8

    Black wire from fan motor how to wire your ceiling fan 1. Connect the green grounding lead from the hanger ball, the green grounding lead from the hanger bracket to the supply grounding con duc tor (this may be a bare wire or wire with green colored insulation). Securely connect wires with wire conn...

  • Page 9

    3. Screw in two threaded rods into the hanger bracket (fig. 10a). Note: the threaded rods in the hanger bracket serves as guides for easier installation. 4. Securely attach the canopy housing to the hanger bracket using the external lockwashers and knurled knobs supplied with your fan (fig. 10b). 5....

  • Page 10

    How to assemble your floor / desk accessory fan 1. Remove floor / desk base from carton. 2. Check to see that you have received the fol low ing parts: • floor / desk base • standard hardware bag 1. 5/16˝-18 x 2½˝ bolt 2. 5/16˝ flat washers (3) 3. Special hex bolt 4. 5/16˝-18 x 1½˝ bolt (for use with...

  • Page 11

    Operating the floor / desk fan 1. Check the operation of the fan by turning the speed control to “high”. 2. Your fan model is equipped with a 4-position, 3-speed control. The operating sequence is as follows: 1 st position - off 2 nd position - high 3 rd position - medium 4 th position - low 1. Afte...

  • Page 12

    How to assemble your pedestal accessory fan note: column is not included and is sold seperately. 1. Remove base from carton. 2. Check to see that you have received the fol low ing parts: • floor base • standard hardware bag 1. 5/16˝-18 x 2½˝ bolt 2. 5/16" flat washers (3) 3. Special hex bolt 4. 5/16...

  • Page 13

    How to assemble your pedestal fan 1. Assemble column to floor base using 15/16˝-18 x 1½˝ bolt and washer (fig. 18). Do not overtighten. 2. After you assembly the column to the floor base, you will proceed to mounting your motor assembly to the column. 3. Secure the hex bolt and washer into the top o...

  • Page 14

    1. Check to see that you have received the fol low ing parts: • wall bracket • standard hardware bag 1. 5/16˝-18 x 2½˝ bolt 2. 5/16˝ flat washers (3) 3. Special hex bolt 4. 5/16˝-18 x 1½˝ bolt (for use with pedestal acc.) • wall unit hardware bag 1. Two #12 x 3˝ wood screws. 2. Two 5/16” plastic hol...

  • Page 15

    Wall brack et hex bolt & washer mounting wall bracket to wall 1. Determine approximate position of fan. 2. Locate stud in your wall. 3. For stud installation the top and bottom holes on wall bracket will be used. These holes are on 11” centers. 4. Position wall bracket on dry wall and mark hole loca...

  • Page 16

    Using your wall fan 1. Your fan is now ready to operate. 2. Plug the fan into a u.L. Approved 120 volt outlet. Operating your wall fan 1. Check the operation of the fan by turning the speed control to “high”. 2. Your fan model is equipped with a 4-position, 3-speed control. The operating sequence is...

  • Page 17: Trouble

    Trouble shooting trouble probable cause suggested remedy 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connections to the motor assembly. 1. Fan will not start. 1. Check main and branch cir- cuit fuses or circuit breakers. 2. Check line wire conne...

  • Page 18

    Before discarding packaging material, be certain all parts have been removed. 16 ** insert finish codes * * * * * * * * * * * * motor assembly model # fph210_ _ item # description part # 1 motor assembly fph210_ _ ceiling fan accessory model # fph81_ _ item # description part # ceiling canopy / hang...

  • Page 19

    17 12 4 5 9 11 1 16 15 14 10 13 6 3 2 17 18 ceiling fan unit 8 7.

  • Page 20

    18 24 23 22 21 1 floor/desk unit motor assembly model # fph210_ _ item # description part # 1 motor assembly fph210_ _ floor / desk accessory model # fph41_ _ item # description part # 21 floor / desk base phdb standard hardware bag 22 5/16˝-18 x 2½˝ bolt 23 5/16˝ flat washers (3) phshb 24 special h...

  • Page 21

    19 22 23 24 23 25 26 27 1 pedestal unit motor assembly model # fph210_ _ item # de scrip tion part # 1 motor assembly fph210_ _ pedestal accessory model # fph21_ _ item # description part # 26 floor base phfb 27 pedestal column (optional) phpc standard hardware bag 22 5/16˝-18 x 2½˝ bolt 23 5/16˝ fl...

  • Page 22

    20 22 23 24 30 31 1 28 29 wall unit motor assembly model # fph210_ _ item # description part # 1 motor assembly fph210_ _ wall mount accessory model # fph61_ _ item # description part # 28 wall bracket phwb standard hardware bag 22 5/16˝-18 x 2 ½˝ bolt 23 5/16˝ flat washers (3) phshb 24 special hex ...

  • Page 23

    2. The fans will not os cil late. To swivel the direction of the mo tor as sem bly follow the in struc tions be low. 3. Position fan grill to desired position by hand. Fan position is limited to 30° for ward tilt and 90° back ward tilt (fig. 28). Loosen side bolts on motor assembly. Position motor a...

  • Page 24

    10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website @ www.Fanimation.Com copyright 2007 fanimation 2007/01.