Owner’s manual read and save these instructions the punkah ® motor and fan unit warning: support directly from building structure fan unit fp720_ _ motor assembly fp780_ _ net weight 17 lbs (7.71 kg) net weight 7 lbs (3.18 kg).
Table of contents unpacking instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 electrical and structural requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 wiring and control options . . . ...
3 this manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will ...
4 electrical and structural requirements wiring and control options please choose one of the following options and proceed to the page as indicated. 1. Motor can be plugged into electrical outlet. 2. Motor can be wired directly to electrical service with a standard light swich. Your new fan will req...
5 figure 3 wall ceiling no less than 7 ft please choose one of two hanger options for your fan: note: both the motor base and the fan head base must be mounted on the same surface (plane). Option 1 - ceiling mount (figure 2a) option 2 - wall mount (figure 2b) hanging options figure 2b figure 2a caut...
6 motor mounting bracket hanging options - ceiling or wall mount outlet box figure 4 figure 5 figure 6 threaded hole (4 places) - for motor mount junction box threaded hole (4 places) - for motor mount threaded hole (4 places) - for motor mount cross-member support beam ceiling joist junction box 4˝...
7 option 1 - direct plug-in socket: 1. Position mounting plate with the outlet nearby. Attach mounting plate to ceiling or wall with a minimum of two lag bolts into building structure (see previous page). 2. Hook the motor assembly onto the mounting plate. Pivot the motor assembly into place and sec...
8 mounting head assembly 1. Locating head assemblies; head assemblies need to be 17˝ (minimum) to 48˝ (maximum) distance from motor assembly or other head assembly. 2. Secure the fan unit base to wall or ceiling into building structure using the two lag bolts and fl atwashers provided. Figure 10 3. ...
9 assembling & adjusting connecting rod length 1. Loosen each of the “outer” set screws on the outer rod assembly. 2. Insert each “inner” rod assembly (2 pcs) equal amounts so that the distance between connecting rod end holes is equal to the distance between the center of the motor shaft and center...
Attaching connecting rods (cont’d) option 1 - single linkage confi guration (figure 15a) option 2 - double linkage confi guration (figure 15b) blade holder end 1. Place screw through connecting rod end, nylon washer, and blade holder to match your application. 2. Secure with locking nut. Figure 15b ...
11 final connecting rod adjustments figure 16 installing the blades 1. Turn motor so that motor link is perpendicular to connecting rod (see motor link detail, figure 17). 2. Loosen one of the outer set screws and adjust the length of the connecting rod so that the fan blade is centered on the blade...
12 ref. # description part # fan motor assembly fp780** 1 motor cover assembly c7821** 2 motor assembly c7823 3 mounting plate assembly c7800 motor mounting hardware bag contains: hdwmp780 4 motor cover screw, 5 / 32 ˝-32 x 3 / 8 ˝ (3) 5 lag bolt - 2˝ long (2) 6 lag bolt - 4˝ long (2) 7 external loc...
13 note: the illustration shown is not to scale or its actual confi guration may vary. Wires partially removed for clarity. Parts illustration 10a 8 12 18 19 16 21 5 6 3 2 the punkah ® 13 1 figure 18 20 11 22a 22b 24 14 10b 9 7 4 15 17 23 25.
14 trouble shooting warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose wire connections in the...
10983 bennett parkway zionsville, in 46077 toll free (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2008 fanimation 2008/04.
