- DL manuals
- Fanimation
- Fan
- The Beckwith FP7964 Series
- Owner's Manual
Fanimation The Beckwith FP7964 Series Owner's Manual - page 8
8
How to Assemble Your Ceiling Fan (continued)
7.
Cut off excess lead wire approximately 6 to 9 inches
above top of the top of the downrod. Strip insulation off
1/2 inch from the end of each lead wire. (Figure 7)
NOTE:
All set screws must be checked, and retightened
where necessary, before installation.
Figure 6
Figure 7
6.
Reinstall the hanger ball on the downrod as follows.
Route the three 80 in. wires through the hanger ball.
Position the pin through the two holes in the downrod
and align the hanger ball so the pin is captured in the
groove in the top of the hanger ball. Pull the hanger ball
up tight against the pin. Securely tighten the set screw
in the hanger ball. A loose set screw could create fan
wobble. (Figure 6)
Summary of The Beckwith FP7964 Series
Page 1
Model no. Fp7964** owner's manual read and save these instructions the beckwith ™ ceiling fan net weight 27.16 lbs (12.32 kg).
Page 2
Important safety instructions warning: to avoid fire, shock and serious personal injury, follow these instructions. 1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams. 2. Before servicing or cleaning unit, switch power off at ...
Page 3
Limited lifetime warranty extends to the original purchaser of a fanimation fan 9. It is understood that any repair or replacement is the exclusive remedy available from fanimation. There is no other expressed or implied warranty. Fanimation hereby disclaims any and all implied warranties, including...
Page 4
1. Check to see that you have received the following parts: note: if you are uncertain of part description, refer to exploded view illustration. 4 unpacking instructions for your convenience, check-off boxes are provided next to each step. As each step is completed, place a check mark in the box. Th...
Page 5
5 energy efficient use of ceiling fans ceiling fan performance and energy savings rely heavily on the proper installation and use of the ceiling fan. Here are a few tips to ensure efficient product performance. Choosing the appropriate mounting location ceiling fans should be installed, or mounted, ...
Page 6
6 electrical and structural requirements (continued) if your fan is to replace an existing light fixture, turn electricity off at the main fuse box at this time and remove the existing light fixture. Turning off wall switch is not sufficient. To avoid possible electrical shock, be sure electricity i...
Page 7
7 how to assemble your ceiling fan 1 . Remove the hanger ball portion from the downrod/ hanger ball assembly by loosening the set screw in the hanger ball until the ball falls freely down the downrod. Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for re...
Page 8
8 how to assemble your ceiling fan (continued) 7. Cut off excess lead wire approximately 6 to 9 inches above top of the top of the downrod. Strip insulation off 1/2 inch from the end of each lead wire. (figure 7) note: all set screws must be checked, and retightened where necessary, before installat...
Page 9
9 how to hang your ceiling fan note: if you are not sure if the outlet box is grounded, contact a licensed electrician for advise, as it must be grounded for safe operation. Warning the fan must be hung with at least 7’ of clearance from ƀoor to blades. (figure 2) warning to avoid possible ſre or sh...
Page 10
Receiver unit detail 10 how to wire your ceiling fan main fuse box figure 1 to avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging (figure 1). Warning note: if you are not sure if the outlet box is grounded, contact a licensed electrician for advice...
Page 11
11 how to install the light bulbs 1. Remove the preassembled screws and take off the 4 light caps in the motor assembly. Retain the screws and light caps for later. (figure 1) 2. Install bulbs. (figure 2) 3. Put the light caps back and securely tighten the previously removed screws of light caps. (f...
Page 12
12 how to operate your ceiling fan 1. Restore electrical power to the outlet box by turning the electricity on at the main fuse box. (figure 1) 3. The 5-button hand-held remote transmitter includes buttons for high, medium and low fan speeds as well as fan off and light on/off. (figure 3) 4. If airf...
Page 13
How to install your remote control (option #1) how to install your remote control (option #2) how to install your remote control (option #3) 1. Drill the two 1/4” holes in wall and use the m6 plastic anchor pushed into the holes. Install the control bracket with two #3- 1” self tap screws. Push the ...
Page 14
14 trouble shooting for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Warning trouble probable cause suggested remedy 1.Fan will not start 1. Check main and branch circuit fuses or circuit breakers. 2. Check line wire connections to fan and switch wi...
Page 15
15 parts list model no. Fp7964** reference # description part # 1 adr1-45** 2 pg164** 3 4 ap1115** motor coupling cover 5 recan559 ama7964** receiver unit fan motor assembly 6 tr24wh remote control 7 ppe12b43 ap255bl ap260** bulb 8 9 hdwfp7964 10 wire connector (4) phillips screwdriver 4Ý — — loose ...
Page 16
16 model fp7964** exploded-view note: the illustration shown is not to scale or its actual con ¿ guration may vary. Product/parts are subject to change without notice. Figure 1 the beckwith ™ 10 10 1 2 3 4 5 6 8 7 9.
Page 18
Copyright 2013 fanimation 2013/08 v.01 10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website @ www.Fanimation.Com.
Page 19: Ventilador De Techo
The beckwith ™ ventilador de techo peso neto 12.32 kg (27.16 lbs) modelo n.º fp7964** manual del propietario lea y guarde estas instrucciones.
Page 20
Instrucciones de seguridad importantes advertencia: siga estas instrucciones para prevenir incendios, descargas eléctricas y lesiones personales graves. Lea el manual del propietario y la información de seguridad antes de instalar su nuevo ventilador. Observe los diagramas de 1. Ensamblaje adjuntos....
Page 21
En ningún caso se podrá devolver un ventilador sin previa autorización por parte de fanimation. Las devoluciones autorizadas 8. Deberán ir acompañadas del recibo de venta y deberán enviarse a fanimation, previo pago del flete. El ventilador que se devuelva deberá estar embalado en forma adecuada a f...
Page 22
bolsas de accesorios: – destornillador phillips de 4Ý – conectores de cables destornillador phillips escalera de tijera destornillador de óÝ pelacables tres conectores de cables (incluidos) este manual está diseñado para facilitar al máximo el ensamblaje, la instalación, el funcionamiento ...
Page 23
Requisitos eléctricos y estructurales su nuevo ventilador de techo requiere una línea de suministro eléctrico con conexión a tierra de 120 voltios de ca, 60 hz, circuito de 15 amperios. La normativa eléctrica requiere el uso de una caja de distribución eléctrica para ventiladores que soporte el peso...
Page 24
6 requisitos eléctricos y estructurales (cont.) si su ventilador va a sustituir una instalación de iluminación existente, desconecte la electricidad de la caja del fusible principal en esta ocasión y extraiga la unidad de iluminación. No bloqueo (figura 3) conectado a una caja de distribución eléctr...
Page 25
25 cómo ensamblar el ventilador de techo figura 1 figura 2 figura 3 figura 4 figura 5 2 . Retire el clip de horquilla y pasador de horquilla de la parte inferior de la bola para colgar. Retener el pasador y clip para la reinstalación en el paso 4. (figura 2) 1. Extraiga la pieza de la bola colgante ...
Page 26
26 cómo ensamblar el ventilador de techo (cont.) figura 6 figura 7 6. Vuelva a colocar la semiesfera en el barral como se indica a continuación. Pase los tres cables de 2.03 m (80Ý) a través de la semiesfera. Pase el pasador a través de los dos orificios en el barral y alinee la semiesfera de modo q...
Page 27
2. Levante cuidadosamente el ventilador y coloque el ensamble de la bola para colgar/varilla en la abrazadera para colgar que acaba de fijar a la caja de salida. Asegúrese de que la ranura de la bola esté alineada con la lengüeta de la abrazadera para colgar. (figura 4) advertencia para evitar una p...
Page 28
Note: el mando a distancia incluido en este ventilador tiene 16 combinaciones diferentes de códigos. Para evitar posibles interferencias desde o hacia otros mandos a distancia, modifique el código de combinación de su transmisor y receptor. 1. Para configurar el código del transmisor, extraiga la ca...
Page 29
29 2. Instale la bombillas. (figura 2) figura 3 tapas de iluminación figura 2 figura 1 ensamble del motor figura 1 figura 2 bombilla cómo instalar la carcasa de la cubierta nota: este paso se debe realizar luego de completar la completed. Instalación eléctrica necesaria. 1. Extraiga una de los torni...
Page 30
Mando a distancia de 5 botones figura 3 figura 1 2. Para que funcione el ventilador, instale dos pilas de 3 voltios en el transmisor del mando a distancia. 3. El transmisor del mando a distancia de 5 botones incluye 5 botones para controlar las velocidades baja, media y alta del ventilador, así como...
Page 31
Figura 1 figura 1 figura 2 figura 1 figura 2 cómo instalar su mando a distancia (opción #1) 1. Retire los dos tornillos colocados en la plaza del interruptor de la pared. (figura 1) 2. Instale el soporte de control con los dos tornillos #6-32x 3/4”. Empuje los cuatro tapones de plástico para cubrir ...
Page 32
Solución de problemas problema causa posible solución sugerida 1. El ventilador no arranca 1. El fusible o el disyuntor están fundidos. 2. Las conexiones eléctricas del ventilador o del interruptor en la caja del interruptor están flojas. 3. El conmutador inversor se encuentra en posición neutra. 4....
Page 33
33 modelos n.° fp7964** lista de piezas adr1-45** pg164** ap1115** recan559 ama7964** tr24wh ppe12b43 ap255bl ap260** hdwfp7964 — — 1 2 3 4 5 receptor 6 mano a distancia 7 bombilla (4) 8 9 10 — — conectores de cables (4) destornillador phillips de 4Ý bolsa de accesorios que conti unidad del soporte ...
Page 34
34 figura 1 the beckwith ™ 10 10 1 2 3 4 5 6 8 7 9 modelo n.º fp7964** despiece nota:.
Page 36
Copyright 2013 fanimation 2013/08 v.01 10983 bennett parkway zionsville, in 46077 llame sin cargo al (888) 567-2055 fax (866) 482-5215 desde fuera de los ee.Uu. Llame al (317) 733-4113 visite nuestro sitio web en www.Fanimation.Com.