Owner’s manual read and save these instructions model no. Fp3120** the vetricco ® ceiling fan vetricco ® fan satin nickel finish shown with plastic blade set vetricco ® fan glossy black finish shown with plastic blade set net weight 17.1 kg (38 lbs).
Table of contents unpacking instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 electrical and structural requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be...
4 electrical and structural requirements your new ceiling fan will require a grounded electrical supply line of 120 volts ac, 60 hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 1 depicts different structural configurations th...
5 how to assemble your ceiling fan (cont’d) note: you will be using either the 6˝ downrod supplied with your fan or an optional downrod purchased seperately. 4. Loosen the two setscrews in the downrod support. Align the clevis pin holes in the downrod with the holes in the downrod support. Install t...
6 how to hang your ceiling fan figure 1 floor ceiling no less than 7 ft ▲warning to avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging. Note: if you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must b...
7 how to wire your ceiling fan - c26 remote control operating instructions - c26 remote control 1. Operating & using remote transmitter (figure 3): install 9 volt battery (if not using for long periods of time, remove battery to prevent damage to transmitter). Store the transmitter away from excess ...
8 assembling and mounting the fan blades 1. Lay blade medallion with the threaded posts facing up. 2. Position the plastic blade over the blade medallion with the threaded posts showing through the holes of the blade. (see insert for what side of blade that faces the medallion) 3. With a philips scr...
9 figure 1 3. Securely attach plugs from motor to sockets on downlight socket plate assembly (figure 3) installing the lower housing assembly 1. Loosen four screws and remove one screw from support flange. (figure 1). Figure 2 figure 3 2. Be sure to “square” or line up the corners of the adapter pla...
10 installing the lower housing assembly (cont’d) figure 4 figure 5 figure 6 4. Securely attach downlight socket plate assembly to the adapter plate by tightening three screws with spring washers ( 5 / 32 -32 x 8 mm) provided with the fan. (figure 4) 5. Install three candelabra bulbs (not included -...
11 maintenance blade cleaning periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the fi nish. Abrasive cleaning agents are not required and should be avoided to prevent damage to fi nish. Perio...
¾¾ insert finish codes (refer to fan model number located on downrod support) 12 before discarding packaging materials, be certain all parts have been removed parts list model #fp3120** ref. # description part # 1 hanger bracket assembly apg510bl 2 downrod/hanger ball assembly containing: adr6 ¾¾ 2a...
13 note: the illustration shown is not to scale or its actual confi guration may vary the vetricco ® fp3120** exploded-view 4 1 figure 1 3 2a 8 12 ref 7 6 5 14 10 11 2b 2c 2d 2 13 12 reversing switch 9.
14 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2007 fanimation 2007/08.
