Owner’s manual read and save these instructions model no. Fp4210** the volare ® ceiling fan volare ® fan chrome finish shown with mahogany blade set volare ® fan oil-rubbed bronze finish shown with cherry blade set volare ® fan satin nickel finish shown with maple blade set net weight 16.22 kg (36 l...
Table of contents unpacking instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 electrical and structural requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be...
Clevis pin setscrew (2) 4 electrical and structural requirements your new ceiling fan will require a grounded electrical supply line of 120 volts ac, 60 hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 1 depicts different stru...
5 how to assemble your ceiling fan (cont’d) 6. Position the wood blade with the threaded posts showing through the holes of the blade arm. With a ⅜˝ rachet wrench, tighten locking hex-nuts and flat washers. Do not overtighten. (figure 3) 7. Attach assembled blade arms to the motor hub using the prov...
6 how to hang your ceiling fan figure 1 floor ceiling no less than 7 ft ▲warning to avoid possible electrical shock, be sure electricity is turned off at the main fuse box before hanging. Note: if you are not sure if the outlet box is grounded, contact a licensed electrician for advice, as it must b...
7 how to wire your ceiling fan - c20 remote control operating instructions - c20 remote control 1. Operating & using remote transmitter (figure 3): install 9 volt battery (if not using for long periods of time, remove battery to prevent damage to transmitter). Store the transmitter away from excess ...
8 installing the canopy housing 1. Screw in two threaded rods into the hanger bracket (figure 1a). Note: the threaded rods in the hanger bracket serve as guides for easier installation. 2. Securely attach the canopy housing to the hanger bracket using the external lockwashers and knurled knobs suppl...
9 3. Securely attach plugs from motor to sockets on downlight socket plate assembly (figure 3) figure 3 installing the lower housing assembly (cont’d) figure 4 figure 5 4. Securely attach downlight socket plate assembly to the adapter plate by tightening three screws with spring washers ( 5 / 32 -32...
Maintenance blade cleaning periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the fi nish. Abrasive cleaning agents are not required and should be avoided to prevent damage to fi nish. Periodic...
11 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
12 parts list model #fp4210** ref. # description part # 1 hanger bracket assembly apg510bl 2 downrod/hanger ball assembly containing: adr6 ¾¾ 2a hanger ball assembly 2b downrod 2c hairpin clip 2d clevis pin 3 ceiling canopy pg160 ¾¾ 4 upper housing cover p4274 ¾¾ 5 fan motor/housing assembly ama4210...
13 note: the illustration shown is not to scale or its actual confi guration may vary the volare ® fp4210** exploded-view 4 1 figure 1 3 2a 7 13 ref 6 5 13 9 2b 2c 2d 2 12 8 10 11.
10983 bennett parkway zionsville, in 46077 (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website www.Fanimation.Com copyright 2007 fanimation 2007/08.
