Owner’s manual read and save these instructions models no. Fp7300, fp7400 & fp7500 the windpointe ® ceiling fans fp7300; 3-bladed model fp7400; 4-bladed model fp7500; 5-bladed model windpointe ™ fan model (std) net weight (lbs) net weight (kgs) fp7300 28.46 12.91 fp7400 27¾ 12.58 fp7500 25.57 11.60
1. Limited lifetime motor warranty - if any part of your fan motor fails, due to a defect in materials or workmanship during the lifetime of the original purchaser, fanimation will provide the replacement part free of charge, when the defective fan is returned to our national service center. Proof o...
This manual is designed to make it as easy as possible for you to assemble, install, operate, and maintain your ceiling fan unpacking instructions for your convenience, check-off each step. As each step is completed, place a check mark. This will ensure that all steps have been completed and will be...
4 electrical and structural requirements your new ceiling fan will require a grounded electrical supply line of 120 volts ac, 60 hz, 15 amp circuit. The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Figure 1 depicts different structural configurations th...
How to assemble your ceiling fan pin setscrew hanger ball figure 1 1. Remove the hanger ball by loosening the setscrew in the hanger ball until the ball falls freely down the downrod. (figure 1) remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstal...
6 how to hang your ceiling fan figure 1 floor ceiling no less than 7 ft ▲warning the fan must be hung with at least 7´ of clearance from floor to blades (figure 1) ▲warning the outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. Hanger bracket must seat fi rml...
7 how to wire your ceiling fan - pull chain if you feel that you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. 1. Connect the green grounding lead from the hanger ball and the green grounding lead from the hanger bracket to the suppl...
8 assembling and mounting the fan blades and switch hsg 1. Remove and discard the (rubber) motor “stops” by removing the five screws. (figure 1) blade & blade holder assembly: 2. Lay the side of the blade holder on a flat surface with the inside of the blade holder facing up. 3. Assemble the blade t...
9 maintenance periodic cleaning of your new ceiling fan is the only maintenance that is needed. When cleaning, use only a soft brush or lint free cloth to avoid scratching the fi nish. Abrasive cleaning agents are not required and should be avoided to prevent damage to fi nish. Caution do not use wa...
10 before discarding packaging materials, be certain all parts have been removed parts list models fp7300**, fp7400**, fp7500** ref. # description part # 7300** part # 7400** part # 7500** 1 hanger bracket assembly apg610bl apg610bl apg610bl 2 downrod/hanger ball assembly containing: adr1-6** adr1-6...
11 7 6 5 fp7300**, fp7400**, fp7500** exploded-view 4 1 3 2a 2b 2c 2d 2 note: the illustration shown is not to scale or its actual confi guration may vary figure 1 9 8 7 8 7 8 fp7300** blade holders fp7400** blade holders fp7500** blade holders.
12 trouble shooting ▲warning for your own safety turn off power at fuse box or circuit breaker before trouble shooting your fan. Trouble probable cause suggested remedy 1. Fan will not start 1. Fuse or circuit breaker blown. 2. Loose power line connections to the fan, or loose switch wire connection...
Copyright 2008 fanimation 2008/06 10983 bennett parkway zionsville, in 46077 toll free (888) 567-2055 fax (866) 482-5215 outside u.S. Call (317) 733-4113 visit our website @ www.Fanimation.Com.
