Installation manual item #: 422474 rev date: 2016-04-05 fantech reserves the right to modify, at any time and without notice, any or all of its products’ features, designs, components and specifications to maintain their technological leadership position. Please visit our website www.Fantech.Net for...
2 fantech note warning/ important note information technical information practical tip please read this manual before installing unit for residential use only before installation careful consideration must be given to how this system will operate if connected to any other piece of mechanical equipme...
3 fantech table of contents determining your airflow requirement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 installation examples fully dedicated system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
4 fantech room classification number of rooms cfm (l/s) cfm required master bedroom x 10 l/s (20 cfm) = basement yes or no = bedrooms x 5 l/s (10 cfm) = living room x 5 l/s (10 cfm) = others x 5 l/s (10 cfm) = kitchen x 5 l/s (10 cfm) = bathroom x 5 l/s (10 cfm) = laundry room x 5 l/s (10 cfm) = uti...
5 fantech hrv ducting for fully dedicated system stale air from inside outside fresh air to living areas fresh air from outside stale air to outside installation examples example only – duct configuration may differ depending on the model. Fully dedicated system best for new construction 1. Stale ai...
6 fantech hrv/ furnace ducting for partially dedicated system stale air from inside * unit airflow should be balanced while hrv is on “normal” speed and furnace blower is running. Outside fresh air to living areas 1 m (3' 3") min. Recommended cold air return stale air to outside fresh air from outsi...
7 fantech stale air from inside outside fresh air to living areas 1 m (3' 3") min. Recom- mended cold air return hrv/ furnace for simplified installation – option 1 installation examples (cont'd) direct connection of both the hrv supply air stream and exhaust air stream to the furnace cold air retur...
8 fantech * ductwork layout may differ depend- ing on model direct connection of the hrv supply air stream to the supply air side on the furnace & exhaust air stream to the furnace cold air return simplified installation (good) option 2 1. Furnace blower must operate when ventilation from hrv is req...
9 fantech exterior ducting installation weatherhood location • decide where your intake and exhaust hoods will be located. Locating the intake weatherhood • should be located upstream (if there are prevailing winds) from the exhaust outlet. • at a minimum of 2m (6’) away from dryer vents and furnace...
10 fantech interior ducting installation • to maximize airflow through the ductwork system, all ducts should be kept short and have as few bends or elbows as possible. • 45º elbows are preferable to 90º. • use “y“ ducts instead of “t” ducts whenever possible. • all duct joints must be fastened with ...
11 fantech ducting installation examples fully dedicated system partially dedicated system simplified installation - option 1 simplified installation - option 2 bathroom fresh air exhaust air central control - optional fresh air to living room exhaust cg 4 (4” adjustable grill) fel 4 (4” miter elbow...
12 fantech hrv installation location the hrv must be located in a conditioned space where it will be possible to conveniently service the unit. Typically the hrv would be located in the mechanical room or an area close to the outside wall where the weatherhoods will be mounted. If a basement area is...
13 fantech airflow adjustment & balancing balancing the airflows is crucial to ensure optimal operation of the unit. If the airflow is not properly balanced, the following issues may occur: • significant positive or negative pressure inside the house • unit’s efficiency may be negatively affected • ...
14 fantech balancing steps use balancing chart located on the door of the hrv step #1: identify the desired airflow using the provided chart. From the desired airflow (left column) identify the pressure reading needed by simply following the line. Make sure to set the unit at the normal speed before...
15 fantech low voltage control systems * please see instruction manuals for individual controls for proper wiring and set up of control systems. Central controls these control options can only be used individually controls features connect to eco-touch • our most complete, yet easy to use control sy...
16 fantech wiring diagram * wiring diagram of complete unit inside of access panel observe polarity on all accessory controls where applicable..
17 fantech w r g c y w r g y standard furnace interlock wiring thermostat terminals furnace 24-volt terminal block four wire two wire heating only two wire cooling system w r g c y w r g y alternate furnace interlock wiring thermostat terminals furnace 24-volt terminal block four wire two wire heati...
18 fantech troubleshooting problem causes solutions air is too dry dehumidistat control is set too low increase the desired level of humidity. Change ventilation mode from continuous mode to standby. Hrv out of balance have contractor balance hrv airflows air is too humid dehumidistat control is set...
19 fantech the best limited warranty in the business • the heat recovery aluminum core has a limited lifetime warranty. • the motors found in all fantech hrv’s require no lubrication, and are factory balanced to prevent vibration and promote silent operation. • the limited warranty covers normal use...
20 fantech notes.
Manuel d'installation no. D'article #: 422474 date de révision: 2016-04-05 votre système de ventilation doit être installé conformément aux exigences de la province où vous habitez ou, à défaut de telles exigences, conformément à l’édition actuelle du code national du bâtiment du canada ou aux « mét...
22 fantech note avertissement/ note importante information information technique conseil pratique veuillez lire le manuel avant d’installer l’appareil À fin d’installation résidentielle seulement avant de procéder à l’installation, examinez avec soin la façon dont le système fonctionnera s’il est re...
23 fantech table des matiÈres dÉterminer vos besoins de ventilation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 exemples d'installation système entièrement spécialisé . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
24 fantech liste des pièces nombre de pièces pi3/min (l/s) pcm required chambre principale x 10 l/s (20 pi3/min) = sous-sol oui ou no = chambre à coucher x 5 l/s (10 pi3/min) = salon x 5 l/s (10 pi3/min) = autres x 5 l/s (10 pi3/min) = cuisine x 5 l/s (10 pi3/min) = salle de bain x 5 l/s (10 pi3/min...
25 fantech conduit vrc/fournaise de système entièrement spécialisé air vicié provenant de l'intérieur extérieur air frais distribué à l'intérieur air frais provenant de l'extérieur air vicié évacué à l'extérieur exemples d'installation exemple seulement – la configuration des conduits peut être diff...
26 fantech conduits vrc/fournaise pour système partiellement spécialisé exemples d'installation (suite) raccordement direct du flux d’air d’approvisionnement à la bouche de reprise d’air de la fournaise (l’air vicié est aspiré à partir des endroits clés de la maison.) systÈme partiellement spÉcialis...
27 fantech air vicié provenant de l'intérieur extérieur air frais distribué à l'intérieur 1 m (3pi 3po) min. Recom- mandé retour d'air frais conduits vrc/fournaise pour installation simplifiée exemples d'installation (suite) raccordement direct du flux d’air d’approvisionnement et du flux d’air Évac...
28 fantech installation simplifiÉe (bonne) option 2 1. Si la ventilation du vrc doit être assurée, il peut être nécessaire de faire fonctionner le ventilateur de la fournaise. La fournaise devrait être réglée pour fonctionner continuellement ou en synchronisme avec le vrc. 2. Pour fins d'acceptation...
29 fantech installation des conduits extÉrieurs emplacement des hottes • décidez de l’emplacement des hottes d’aspiration et d’évacuation. Emplacement de la hotte d’aspiration • doit être située en amont de la sortie d’évacuation (en présence de vents dominants). • doit être située à au moins 2m (6 ...
30 fantech installation des conduits intÉrieurs • pour maximiser le débit d’air dans le réseau de conduits, assurez-vous que tous les conduits sont le plus court et le plus droit possible. • il est préférable d’utiliser des coudes de 45 degrés plutôt que des coudes de 90 degrés. • dans la mesure du ...
31 fantech exemples d'installation des conduits système entièrement spécialisé système partiellement spécialisé installation spécialisée - option 1 installation spécialisée - option 2 salle de bains air frais air évacué commande centrale (en option) air frais acheminé au salon grille d'évacuation cg...
32 fantech installation emplacement le vrc doit être situé dans un endroit chauffé où il sera possible d’en effectuer l'entretient convenablement. Généralement, le vrc doit être situé dans la chambre des appareils mécaniques ou à proximité. S’il n’y a pas de sous-sol ou si le sous-sol ne convient pa...
33 fantech 2 installer le tuyau d'écoulement et faite une boucle (siphon en p). 1 posez l'embout de drain Équilibrage du dÉbit d’air si les flux d’air de l’appareil ne sont pas correctement ÉquilibrÉs… • l’efficacitÉ de l’appareil peut Être rÉduite. • des dommages au noyau de rÉtablissement de la ch...
34 fantech Étapes de balancement utilisez la charte de balancement localisée sur la porte du vhc Étape 1: identifiez le débit d’air désiré en vous référent à la charte fournie. Du débit d’air désiré (colonne de gauche) identifiez la lecture de pression nécessaire en suivant tout simplement la ligne....
35 fantech systÈme de contrÔle À basse tension * veuillez voir les instructions individuelles des contrôles pour le câblage et la mise en pièce appropriée. ContrÔles centrals – ces options de contrôle peuvent seulement être utilisé individuellement contrÔle caractÉristiques connexion À eco-touch • n...
36 fantech schÉmas Électroniques * schéma électrique de l'appareil au complet situé à l'intérieur du paneau d'accès.
37 fantech w r g c y w r g y standard furnace interlock wiring thermostat terminals furnace 24-volt terminal block four wire two wire heating only two wire cooling system w r g c y w r g y alternate furnace interlock wiring thermostat terminals furnace 24-volt terminal block four wire two wire heati...
38 fantech dÉpannage problème causes solutions l’air est trop sec – le déshumidistat est réglé trop bas – augmentez le niveau voulu d’humidité. Faites passer le mode de ventilation de « continu » à « attente ». – le vrc est déséquilibré – Équilibrez le vrc. L’air est trop humide – le déshumidistat e...
39 fantech la meilleure garantie limitée sur le marché • la meilleure garantie limitée sur le marché. • le noyau récupérateur de chaleur en aluminium bénéfice d'une garantie à vie limitée. • les moteurs dont sont dotés tous les vrc de fantech ne nécessitent aucune lubrification et sont équilibrés en...
40 fantech partslist•listedescomposantes bom # description vhr150 (44921) 1 r2e 190 radical, rep. Kit 405520 2 electrostatic filters kit 8.5” x 15” 402041 3 heat recovery cell 9” x 9” x 15” 402063 4 capacitors 8uf 410012 5 pcb, rv-ctrl rev 1.5 420459 6 door switch 410867 7 auto-transformer 411963 8 ...
41 fantech notes.
42 fantech notes.
43 fantech notes.
Fantech reserves the right to make technical changes. For updated documentation please refer to www.Fantech.Net fantech® fantech se réserve le droit de faire des changements tech- niques. Pour de la documentation à jour, s'il vous plaît se référer au www.Fantech.Net.