1. DL manuals
  2. Fantom
  3. Vacuum Cleaner
  4. FM766HG
  5. Instruction Manual

Fantom FM766HG Instruction Manual

Manual is about: Fantom Vacuum Cleaner User Manual

Summary of FM766HG

  • Page 1

    Replacement parts important safety instructions name of each part preparation before use using the vacuum cleaner using the attachments emptying the dust compartment cleaning the filters clearing blockages in the suction hose and cleaning the agitator assembly replacement instructions troubleshootin...

  • Page 2

    Important safety instructions when using an electrical appliance, basic precautions should always be followed, including the following. Read all instructions before using this vacuum cleaner warning - to reduce the risk of fire, electric shock or injury: 1. Do not leave the vacuum cleaner when plugg...

  • Page 3: Save These Instructions

    2 16. Do not touch the agitator while it is spinning. 17. Do not place any heavy items on top of the vacuum cleaner. 18. Do not step on the hose or pull it too strongly. 19. Do not pick up items such as pieces of waste paper or cloth which looks as though they may cause the hose to become blocked. 2...

  • Page 4: Names Of Each Part

    3 names of each part warning: operate vacuum cleaner only at the voltage specified on name plate. Front rear set the on/off switch to " on " to light the headlight. Cleaning utensil headlight handle suction hose a dust compartment carrying handle duster knob on/off switch release button a release bu...

  • Page 5: Attaching The Handle

    Handle wand crevice tool upholstery tool & dusting brush duster hose cuff suction inlet suction hose a caution: do not connect the power cord plug to the wall outlet until assembly is completed. Attaching the handle preparations before use attaching the suction hose a & attachments 4 1 2 set the vac...

  • Page 6: Preparations Before Use

    5 preparations before use winding the power cord 1 wind the power cord around the cord storage hooks. Secure the power cord plug on the power cord. Cord storage hooks thermal safety device in main body to protect your vacuum cleaner motor from overheating, a thermal safety device has been built in. ...

  • Page 7: Using The Vacuum Cleaner

    Handle release lever handle release lever parallel position this position is used for cleaning under furniture. 6 using the vacuum cleaner adjusting the handle upright position the handle is normally locked in this the handle of this vacuum cleaner can be set to one of three positions -upright, norm...

  • Page 8: Edge Cleaning

    Rug/floor (tools) selector edge cleaning this vacuum cleaner is equipped with an "edge cleaning" function for cleaning carpet edges near baseboards and stationary furniture. 7 1 2 rug/floor (tools)selector the rug/floor(tools)selector should only be adjusted while the vacuum cleaner is turned on and...

  • Page 9: Using  The  Attachments

    Holder mount hose holder release button c wand crevice tool duster attachment clamp caution: when using one of the attachments during cleaning,set the vacuum cleaner to the upright position. 1 2 3 using the attachments press the release button c to disconnect the handle from the vacuum cleaner. Remo...

  • Page 10: Using The Attachments

    Hose cuff suction inlet suction hose a using the attachments 9 hose attachment line up notches push hose in till it clicks. Handle.

  • Page 11

    Projection groove max mark 1 1 2 3 2 4 1 2 trapdoor release lever duster handle turn the duster handle several times in the direction shown to empty the dust compartment. Emptying the dust compartment caution: be sure to turn the on/off switch to the "off" position and disconnect the power cord from...

  • Page 12: Cleaning The Filters

    Remove the dust compartment.(refer to page 11) clean the filter fins free of dirt with the forked end of cleaning utensil as shown. Prefilter dust compartment ribs main filter 1 1 cleaning the filters 2 set the dust compartment to the parallel position.Open the trapdoor,then push the release button ...

  • Page 13: The Agitator Assembly

    Bypass valve (inside) caution: be sure to turn the on/off switch to the "off" position and disconnect cleaning the agitator assembly 1 2 3 clearing blockages and cleaning the agitator assembly the power cord from the wall outlet before clearing any blockages in the suction hose and cleaning the agit...

  • Page 14: Replacement  Instructions

    Replacing the headlight lamp replacement instructions caution: be sure to turn the on/off switch to the"off" position and disconnect the power cord from the wall outlet before replacing any of the parts below. 1 set the vacuum cleaner to the parallel position. 2 loosen the screws to remove the lens....

  • Page 15: Replacement  Instructions

    Place a new flat belt onto the motor shaft and pulley. 1 2 3 4 5 replacement instructions caution: be sure to turn the on/off switch to the"off" position and disconnect the power cord from the wall outlet before replacing any of the parts below. Replacing the flat belt remove the bottom plate. (refe...

  • Page 16: Replacement  Instructions

    Loosen screw latch mounting screw projection groove tighten screw latch bottom plate 15 1 1 replacement instructions removing the bottom plate set the vacuum cleaner to the parallel position and turn it over. Reattaching the bottom plate insert the projection on the bottom plate into the groove on t...

  • Page 17: Replacement Instructions

    Filter cover seal 1 1 1 1 2 2 hepa filter 2 2 1 1 sub-filter air inlet cover caution: be sure that seal on the hepa filter is inserted towards the inside of the vacuum cleaner. The filter cover should be correctly oriented when it is reattached. Do not reattach it upside down. 3 insert a new hepa fi...

  • Page 18: Troubleshooting

    If there is a problem with the vacuum cleaner, carry out the following checks to find the cause. If the problem still persists after the checks have been made, do not use the vacuum cleaner to prevent the possibility of an accident occurring. Turn the on/off switch to the "off" position, disconnect ...

  • Page 19

    In us: fantom, 94 main mill street, door 16, plattsburgh, n.Y. 12901 return to fantom , 94 main mill street, door 16 , plattsburgh , n.Y . 12901 ownership registration card please fill out and mail the product registration card within ten (10) days of purchase. The registration will enable us to con...