1. DL manuals
  2. Fantom
  3. Saw
  4. PT301H
  5. Owner's Manual

Fantom PT301H Owner's Manual

Manual is about: SPIN SAW / ROTARY TOOL KIT

Summary of PT301H

  • Page 1

    Owner’s manual spin saw / rotary tool kit model no. Pt301h caution: before using this spin saw/rotary tool, read this manual and follow all its safety rules and operating instructions. · safety instructions · accessories · assembly · operation · maintenance fantom, 178 west service road, champlain, ...

  • Page 2: Product Specifications

    Product specifications rev. 05/03 section page section page product specifications …………………. 2 carton contents ………………………… 6, 7 power tool safety ..…………………….. 3 know your spin saw ……………….. 8 spin saw / rotary tool safety .……... 4 assembly & operation …….…………… 9 – 17 electrical requirements & safety ……...

  • Page 3: Power Tool Safety

    General safety rules read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury. Work area keep your work area clean and well lit. Cluttered benches and dark areas invite accidents. Do not operate power tool...

  • Page 4: Spin Saw Symbols

    Spin saw symbols some of the following symbols may be used on your tool. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the tool better and safer. Warning ! Service tool service must be performed only by qualified personnel. Service or mai...

  • Page 5

    This cutting tool is double insulated to protect you from electrical shock. Double insulated tools are equipped with a polarized plug (one blade is wider than the other). This plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it ...

  • Page 6

    Available accessories use only accessories recommended for this spin saw. Follow instructions that accompany accessories. Use of improper accessories may cause injury to the operator or damage to the spin saw. Use only accessories designed for this spin saw to avoid severe injury or tool damage. Do ...

  • Page 7: Carton Contents

    Spin saw components key description qty a spin saw 1 b precision handle with sole plate 1 c freehand sole plate attachment 1 d circle cutter attachment 1 e circle cutter installation adapter 1 f router base attachment 1 g 1/8” collet 1 h 1/4” collet 1 i 1/8” lateral style drywall cutter has "000028 ...

  • Page 8: Know Your Spin Saw

    Know your spin saw 8.

  • Page 9: Assembly & Operation

    Remove the plug from the power source before assembly, changing accessories or cutters and making adjustments. This safety action will help prevent accidental starting of the tool which could result in serious injury. On / off switch this spin saw is equipped with a sliding on / off switch (1) locat...

  • Page 10: Assembly & Operation

    Changing collet insert the cutting bits for this tool are locked into place with a collet nut (1) and collet (see fig. 3). The tool is assembled at the factory with a 1 / 8 ” collet (2) which is used to hold the cutting bit. An additional ¼” collet (3) is supplied for holding small router bits with ...

  • Page 11: Assembly & Operation

    Practice cuts using freehand sole plate before attempting to work on an actual project, take the time to make a few practice cuts with your spin saw. Use some scraps of material that are the same material as used in your actual project. 1. Draw a pattern similar to your first project on a scrap piec...

  • Page 12: Assembly & Operation

    Cutting outlet openings in drywall do not attempt to use this tool to make cut-outs around any fixture or opening which has live electrical wires or on any wall which may have electrical wiring behind it. If a live wire is contacted, the bit could conduct the electric current to the tool, creating a...

  • Page 13: Assembly & Operation

    Installing precision handle the precision handle is designed for use when precision control over the tool movement is desired. The comfortable handle can be used with either the right or left hand. 1. Remove accessory locking knob (1) from the base of the spin saw motor housing (see fig. 10). Slide ...

  • Page 14: Assembly & Operation

    Circle cutter operation unplug the tool from the power source before changing accessories, changing bits and making adjustments. Before turning the tool on, check to make sure bit and all accessory fasteners are securely tightened. 1. Mark the center of the circle you wish to cut on the workpiece an...

  • Page 15: Assembly & Operation

    The router accessory converts your spin saw into a small hobby router that is capable of handling small ¼” shank router bits as well as the spiral cutting bit. The tilting base is ideal for bevel cutting. Unplug the tool from the power source before changing accessories, changing bits and making adj...

  • Page 16: Assembly & Operation

    Freehand cutting and routing when the router base accessory is installed on the spin saw, it will function as a small router to be used for freehand cutting of irregular shaped patterns. You can cut patterns out of the workpiece with the cutting bit or route patterns into the workpiece with small ro...

  • Page 17: Operation & Maintenance

    Cutting curved line with a template to cut a curved line, you can use a curved template to guide the router base. 1. Make a template from hardboard or other similar material to the shape you require (see fig. 20). Note: radius of curve must be greater than 2 ½” for router base to properly follow the...

  • Page 18

    Printed in china model pt301h two (2) year limited warranty fantom warrants this product to be free from defects in material and workmanship for a period of two (2) years from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions a...