1. DL manuals
  2. Fanvil
  3. Gateway
  4. A2
  5. Product User Manual

Fanvil A2 Product User Manual

Manual is about: IP gateway

Summary of A2

  • Page 1

    Fanvil product user manual ip-gateway model: a2 version：v1.0.90.16 © 2005 fanvil technology co,. Ltd all rights reserved. This document is supplied by fanvil technology co., ltd, no part of this document may be reproduced, republished or retransmitted in any form or by any means whatsoever, whether ...

  • Page 2

    Safety notices please read the following safety notices before installing or using this gateway. They are crucial for the safe and reliable operation of the device. Z please use the external power supply that is included in the package. Other powers supplies may cause damage to the device, affect th...

  • Page 3

    Table of content 1. W elcome to the a2 two - port gateway ........................................................................... 5 1.1. Package contents..................................................................................................... 5 2 u nderstanding of a2 two - port gatew...

  • Page 4

    5.3.5.5. Account config............................................................................................................ 38 5.3.5.6. Reboot .......................................................................................................................... 39 5.3.6. Security ..........

  • Page 5

    1. Welcome to the a2 two-port gateway 1.1. Package contents please check your product packaging，it includes: 1. One a2 two-port gateway 2. A group of cable 3. A power adapter note: if you use the non-a2 two-port gateway comes with a power adapter, two-port gateway may cause damage or other injury. S...

  • Page 6

    2 understanding of a2 two-port gateway a2 two-port gateway ip-based voice media access device is designed for operators, enterprises, residential users, and residential voip solution to provide network equipment. A2 two- port gateway into the analog voice information transmitted over ip networks, wh...

  • Page 7

    2.2. Indicator signs name meaning description power power led always light, has power, you can start using the a2 two-port gateway. Fxs1 phone work status lights show the status of the phone under the port 1. No phone or hang up: off; pick up: always. Fxs2 phone work status lights show the status of...

  • Page 8

    A2 two-port gateway with two network interface itself: wan port and lan port, you can use the internet connection into the wan port or lan port. Read the manual carefully of “safety” before inserting the power.

  • Page 9

    3. Getting started before you start using the a2 two-port gateway, please install the following: 3.1. Connect the power and network 3.1.1. Connect the network during this step, make sure your environment already have broadband internet access capability. 1. Broadband router direct network connection...

  • Page 10

    3.1.2. Connect the power during this step, make sure your power supply connector and a2 two-port gateway outlet match, while a2 is also in line voltage and current required for a two-port gateway. 1. The transformer connected to the dc port on the back of a2 two-port gateway power jack. 2. The ac ad...

  • Page 11

    4. Basic phone operation of a2 two-port gateway since there are two fxs interfaces on the a2 two-port gateway, and the two interfaces are independent, so the phones under the fxs1 and fxs2 have the same operation. The phones under the two ports can be used as two separate telephones at the same time...

  • Page 12

    Button again, you can switch back. You also can send and receive on one side, then the party can not be retained to hear your conversation, the speaker you can not. (to use this feature, you must enable the gateway of the call waiting feature) 5. Web configuration 5.1. Introduction of configuration ...

  • Page 13

    5.3. Configuration via web 5.3.1. Basic 5.3.1.1. Status status field name explanation network shows the configuration information on wan and lan port, including the connect mode of wan port (static, dhcp, pppoe), mac address, the ip addresses of wan port and lan port, on or off of dhcp mode of lan p...

  • Page 14

    Please select the proper network mode according to the network condition. A2 gateway provide three different network settings: z static: if your isp server provides you the static ip address, please select this mode, and then finish static mode setting. If you don’t know about parameters of static m...

  • Page 15

    Enable register start to register or not by selecting it or not. Display detailed information that you manual config. Choose dhcp mode，click【next】can config sip(default sip1)simply, also can browse too. Click【back】can return to the last page. Like static ip mode。 choose pppoe mode，click【next】can con...

  • Page 16

    Field name explanation active ip the current ip address of the gateway. Current netmask the current netmask address. Mac address the current mac address of the gateway. Current gateway the current gateway ip address. Get mac time shows the time of getting mac address please select the proper network...

  • Page 17

    If you uses pppoe mode，you need to make the above setting. Pppoe server it will be provided by isp. Username input your adsl account. Password input your adsl password. Notice: 1）click “apply” button after finished your setting, ip gateway will save the setting automatically and new setting will tak...

  • Page 18

    Disabled. 5.3.2.3. Qos config the gateway support 802.1q/p protocol and diffserv configuration. Vlan functionality can use different vlan ids by setting signal/voice vlan and data vlan. The vlan application of this device is very flexible. In chart 1, there is two-layer switch without setting vlan. ...

  • Page 19

    Qos configuration field name explanation vlan enable before select it to enable vlan, you need enable bridge mode in lan config. Vlan id check enable enable vlan id check by selecting it. After enable vlan id check, if vlan id of a data package is not the same with the gateway or a data package do n...

  • Page 20

    4) startup vlan, if set voice/data vlan differentiated as data untagged, then the packet of the signal/voice will use the voice vlan id as the tag, but the data packets will not take the vlan tag. 5) if disable the vlan, regardless to set the voice/data vlan differentiated or not, all packets will n...

  • Page 21

    5.3.2.5. Dhcp server dhcp server field name explanation dhcp leased table ip-mac mapping table. If the lan port of the gateway connects to a device, this table will show the ip and mac address of this device. Shows the dhcp lease table， the unit of lease time is minute. Lease table name specify the ...

  • Page 22

    Between start ip and end ip by dhcp. Netmask set the netmask of the lease table gateway set the gateway of the lease table lease time set the lease time of the lease table dns set the default dns server ip of the lease table; click the add button to submit and add this lease table select name of lea...

  • Page 23

    Sip config field name explanation choose line to set info about sip, there are 3 lines to choose. You can switch by 【load】 button. Register status shows if the gateway has been registered the sip server or not; or so, show unapplied; server name set the server name. Server address input your sip ser...

  • Page 24

    Proxy server address set proxy server ip address（usually, register sip server configuration is the same as proxy sip server. But if your voip service provider give different configurations between register sip server and proxy sip server, you need make different settings.） proxy server port set your...

  • Page 25

    Is enable. Nat keep alive enable/disable keeps nat of sip alive. If some server refuse to register with too short interval time, and has no packets sending to device in private network to keep nat alive, user could set this function on. And set the interval time less than the nat server’s. Enable vi...

  • Page 26

    Notify from the server. Rtp encode enable/disable rtp encrypt. Enable session timer set enable/disable session timer, whether support rfc4028.It will refresh the sip sessions. Answer with single codec enable/disable the function when call is incoming, phone replies sip message with just one codec wh...

  • Page 27

    Stun field name explanation stun nat transverse shows stun nat transverse estimation, true means stun can penetrate nat, while false means not. Stun server addr set your sip stun server ip address stun server port set your sip stun server port stun effect time set stun effective time. If nat server ...

  • Page 28

    01062213123, but you need dial only 162213123 to realize your long distance call after you make this setting. To save the memory and avoid abundant input of user, add the follow functions: 1、x match any single digit that is dialed. If user makes the above configuration, after user dials 11 digit num...

  • Page 29

    Phone number to realize calling to what your prefix number is mapped. The prefix number supports at most 30 digits destination set destination address. This is optional config item. If you want to set peer to peer call, please input destination ip address or domain name. If you want to use this dial...

  • Page 30

    Phone number are deleted according to delete length. This setting will realize speed dial function, after you dialing the numeric key “2”, the number after all will be sent out. When you dial “2”, the sip1 server will receive 33334444 the phone will automatically send out alias number adding your di...

  • Page 31

    If your dialed phone number starts with your set phone number. The phone will send out your dialed phone number adding suffix number. When you dial “147”, the sip1 server will receive “1470011” 5.3.4. Phone 5.3.4.1. Dsp config in this page, you can configure voice codec, input/output volume and so o...

  • Page 32

    Signal standard select signal standard. Flashhook min time set the minimum time detection of inserted spring. Flashhook max time set the maximum time inserted spring. Dtmf payload type dtmf effective load vad select it or not to enable or disable vad. If enable vad, g729 payload length could not be ...

  • Page 33

    No answer time specify no answer time do not disturb select no disturb, the phone will reject any incoming call, the callers will be reminded by busy, but any outgoing call from the phone will work well. Accept any call if select it, the phone will accept the call even if the called number is not be...

  • Page 34

    Notice: black list and limit list can record at most10 items respectively. 5.3.4.3. Digital map configuration this system supports 4 dial modes: 1). End with “#”: dial your desired number, and then press #. 2). Fixed length: the phone will intersect the number according to your specified length. 3)....

  • Page 35

    In length. N is mandatory and can have a value of 0 to 9 seconds. Tn must be the last 2 characters of a dial plan. If tn is not specified it is assumed to be t0 by default on all dial plans. Cause extensions 1000-8999 to be dialed immediately cause 8 digit numbers started with 9 to be dialed immedia...

  • Page 36

    System will use mac as config file name if config file name keep blank. For example, 000102030405.。 config encrypt key input the encrypt key, if the configuration file is encrypted. Protocol type select the protocol type ftp、tftp or http. Update interval time set update interval time, unit is hour. ...

  • Page 37

    Server port set syslog server port. Mgr log level set the level of mgr log. Sip log level set the level of sip log. Enable syslog select it or not to enable or disable syslog. 5.3.5.3. Config setting config setting field name explanation save config you can save all changes of configurations. Click ...

  • Page 38

    5.3.5.4. Update you can update your configuration with your config file in this web page. Update field name explanation web update click the browse button, find out the config file saved before or provided by manufacturer, download it to the gateway directly, press “update” to save. You can also upd...

  • Page 39

    Account configuration field name explanation this table shows the current user existed. User name set account user name. User level set user level, root user has the right to modify configuration, general can only read. Password set the password. Confirm confirm the password. Select the account and ...

  • Page 40

    5.3.6. Security 5.3.6.1. Mmi filter mmi filter user could make some device own ip, which is pre-specified, access to the mmi of the gateway to config and manage the gateway. Field name explanation mmi filter ip table list: add or delete the ip address segments that access to the phone. Set initial i...

  • Page 41

    5.3.6.2. Firewall firewall configuration in this web interface, you can set up firewall to prevent unauthorized internet users from accessing private networks connected to the internet (input rule), or prevent unauthorized private network devices from accessing the internet (output rule). Firewall s...

  • Page 42

    Ip. Src addr set source address. It can be single ip address, network address, complete address 0.0.0.0, or network address similar to *.*.*.0 src mask set the source address’ mask. For example, 255.255.255.255 means just point to one host; 255.255.255.0 means point to a network which network id is ...

  • Page 43

    Nat configuration field name explanation ipsec alg it is an encryption technology. Select it to enable ipsec alg, the default is enable ftp alg ftp is a service of connection layer which can transform intranet ip into extranet ip when intranet ip is sending out packet. Select it to enable ftp alg, t...

  • Page 44

    Click the delete button to delete the selected mapping table. 5.3.6.4. Vpn config this web page provides us a safe connect mode by which we can make remote access to enterprise inner network from public network. That is to say, you can set it to connect public networks in different areas into inner ...

  • Page 45

    Enable vpn select it or not to enable or disable vpn； vpn server addr set vpn l2tp server ip address vpn user name set user name access to vpn l2tp server vpn password set password access to vpn l2tp server vpn server addr set vpn pptp server ip address vpn user name set user name access to vpn pptp...

  • Page 46

    6. Appendix 6.1. Specification 6.1.1. Hardware item a2 gateway adapter (input/output) input: 100-240v output: 12v 1a wan 10/100base- t rj-45 for lan port lan 10/100base- t rj-45 for pc operation temperature 0～40℃ relative humidity 10～65% main chip ralink mips 24kec (320mhz) sdram 16m flash 4m 6.1.2....

  • Page 47

    Z support vlan (optional: voice vlan/ data vlan),support ntp z support vpn (l2tp/pptp) function z wan port supports main dns and secondary dns server can select dynamically to get dns in dhcp mode or statically set dns address. Z qos with diffserv z support dns relay, supports ntp client, firewall s...

  • Page 48

    Can not access the internet access modes commonly used example (already installed on your computer dial-up software) description: 1、make sure the front of the problem does not exist. 2、make sure that dial-up software is properly installed and set. 3、sure to enter the correct user name and password. ...