1. DL manuals
  2. Fanvil
  3. IP Phone
  4. FV6030
  5. User Manual

Fanvil FV6030 User Manual

Summary of FV6030

  • Page 1

    User manual fv6030 voip phone corporate headquarters fanvil technology co., ltd address: unit 4a, building no.7, tian an industrial park, nanshan district, shenzhen 518054 china web site: www. Fanvil.Com tel: +86 755 26502022 fax: +86 755 26505858 version: v1.7.176.166 © 2005 fanvil technology co,. ...

  • Page 2: Safety Notices

    - 2 - safety notices please read the following safety notices before installing or using this phone. They are crucial for the safe and reliable operation of the device. Z please use the external power supply that is included in the package. Other power supplies may cause damage to the phone, affect ...

  • Page 3: Table of Content

    - 3 - table of content 1. Introducing fv6030 voip phone ......................................................................... 5 1.1. Thank you for your purchasing fv6030 .................................................................... 5 1.2. Delivery content ....................................

  • Page 4

    - 4 - 4.3.4. Phone ................................................................................................................................... 40 4.3.5. Maintenance ........................................................................................................................ 47 4.3...

  • Page 5: 1.2. Delivery Content

    - 5 - 1. Introducing fv6030 voip phone 1.1. Thank you for your purchasing fv6030 thank you for your purchasing fv6030, fv6030 is a full-feature telephone that provides voice communication over the same data network that your computer uses. This phone functions not only much like a traditional phone,...

  • Page 6

    - 6 - key key name function description menu in idle state，press the menu key to call up the menu. Up/down of navigation use this key to choose item in the menu. In the idle mode, use this key to display net mode, ip address and gateway’s ip. In the pick up mode, use this key to choose line to call ...

  • Page 7: 1.4. Port For Connecting

    - 7 - more details). In the idle mode, press this key lcd will show ”call forward”, wait this indication disappear, then can configure the forward phone no. Of sip1-5. Press soft2(on) then enabled call forward function and set it to always mode; press soft1(off) will close the function of forward mu...

  • Page 8: 2.1. Connect The Phone

    - 8 - 2. Initial connecting and setting 2.1. Connect the phone step 1: connect the ip phone to the corporate ip telephony network. Before you connect the phone to the network, please check if your network can work normally. You can do this in one of two ways, depending on how your workspace is set u...

  • Page 9: 2.2. Basic Initialization

    - 9 - section “initial setting” to set your network online mode. If your voip phone registers into corporate ip telephony server, your phone is ready to use. 2.2. Basic initialization fv6030 is provided with a plenty of functions and parameters for configuration. User needs some network and voip kno...

  • Page 10

    - 10 - ip with pppoe. Setting static ip mode（static adsl/cable，or none pppoe / dhcp network） 1. Prepare the network’s parameters first. Ip address，netmask， default gateway and dns server ip address are needed. Please contact the service provider or technician of network. 2. Pressing ，and twice，scree...

  • Page 11

    - 11 - displays“3 network” 3. Press soft2 (enter) to show “1 net mode”. After pressing soft(enter) and soft2(edit)，using to select until screen shows “dhcp”. Press soft2(save)，with “saved” displayed, screen will jump to show the net mode currently. 4. Press soft3 (quit) four times quitting to stand-...

  • Page 12: 3.1. Answer Calls

    - 12 - 3. Fv6030’s basic operation 3.1. Answer calls fv6030 will ring to indicate you when there is call incoming，below is ways to answer call： z answer with hook off take handset, you can talk directly. You can just hang up to finish talk。 z answer with handfree press to begin talking. Press again ...

  • Page 13: 3.3. End Calls

    - 13 - if there are many persons records stored in the directory, you can use to search the person which you want to contact. Press to forward，and press to backward. Press soft2 (dial) to dial the current number shown on the screen. Z direct dial direct dial means user can make calls directly withou...

  • Page 14: 3.5. Call Hold

    - 14 - z attended transfer during talk, press and input the number that you want to transfer to and press soft2 (send). After that third party answers, then press to complete the transfer. (you need enable call waiting and call transfer first). If there are two calls, you can just talk to one, and k...

  • Page 15: 3.9. Special Function Key

    - 15 - or press soft2 (detail) to check the details of this record, then press soft2 (dial) again to change the current number. Pressing soft2(dial) will call this number directly if user don’t modify the number. If there is no missed call, screen will show “list is empty”. Z incoming call press and...

  • Page 16

    - 16 - use blf feature. When this configuration enable, the phone will subscribe the status of pointed phone each 60s: led off means idled, led flash means ring and led on means busy. /m mwi (message waiting indication), means the number of this key is the number of voicemail user can configure mwi ...

  • Page 17: 3.10. Call Pickup

    - 17 - key to check the sender’s number and message content, next, press soft2(reply)key and input message content, finally, press soft2(send) again to reply this message. Note: while user browses the message numbers, new messages will be marked by “new”; when user edits message, press # key that to...

  • Page 18: 3.11. Join Call

    - 18 - *1* means appointed prefix code. After making the above configuration, c can dial *1* plus b’phone number to pick up a’s call. User can set prefix in random, in the case of no affecting current dialing rules. 3.11. Join call when b is calling c, a can join in the existing call by inputting an...

  • Page 19: 4. Web Configuration

    - 19 - 4. Web configuration 4.1. Introduction of configuration 4.1.1. Ways to configure fv6030 has three different ways to different users. Z u se phone keypad. Z u se web browser（recommendatory way）. Z u se telnet with cli command. 4.1.2. Password configuration there are two levels to access to pho...

  • Page 20

    - 20 - 4.3.1. Basic 4.3.1.1. Status status field name explanation network shows the configuration information on wan and lan port, including the connect mode of wan port (static, dhcp, pppoe), mac address, the ip address of wan port and lan port, on or off of dhcp mode of lan port. Phone number show...

  • Page 21

    - 21 - please select the proper network mode according to the network condition. Fv6030 provide three different network settings: z static: if your isp server provides you the static ip address, please select this mode, then finish static mode setting. If you don’t know about parameters of static mo...

  • Page 22

    - 22 - display detailed information that you manual config. Choose dhcp mode， click【next】can config sip(default sip1)simply, also can browse too. Click【back】can return to the last page. Like static ip mode。 choose pppoe mode，click【next】can config the pppoe account/password and sip(default sip1)simpl...

  • Page 23

    - 23 - mmi set field name explanation language set set the language of phone, english is default. Greeting message the greeting message will display on lcd when phone is idle. It can support 16 chars. The default chars are voip phone. 4.3.2. Network 4.3.2.1. Wan config wan config field name explanat...

  • Page 24

    - 24 - active ip the current ip address of the phone. Current netmask the current netmask address. Mac address the current mac address of the phone. Current gateway the current gateway ip address. Get mac time shows the time of getting mac address please select the proper network mode according to t...

  • Page 25

    - 25 - notice: 1）click “apply” button after finished your setting, ip phone will save the setting automatically and new setting will take effect. 2）if you modify the ip address, the web will not response by the old ip address. Your need input new ip address in the address column to logon in the phon...

  • Page 26

    - 26 - in chart 1, there is a layer 2 switch without setting vlan. Any broadcast frame will be transmitted to the other ports except the send port. For example, a broadcast information is sent out from port 1 then transmitted to port 2,3and 4. In chart 2, red and blue indicate two different vlans in...

  • Page 27

    - 27 - qos configuration field name explanation vlan enable before select it to enable vlan, you need enable bridge mode in lan config. Vlan id check enable enable vlan id check by selecting it. After enable vlan id check, if vlan id of a data package is not the same with the phone’s or a data packa...

  • Page 28

    - 28 - 4) startup vlan, if set voice/data vlan differentiated as data untaged, then the packet of the signal/voice will use the voice vlan id as the tag, but the data packets will not take the vlan tag. 5) if disable the vlan, regardless to set the voice/data vlan differentiated or not, all packets ...

  • Page 29

    - 29 - 4.3.2.5. Dhcp server dhcp server field name explanation dhcp leased table ip-mac mapping table. If the lan port of the phone connects to a device, this table will show the ip and mac address of this device. Shows the dhcp lease table， the unit of lease time is minute. Lease table name specify...

  • Page 30

    - 30 - select name of lease table, click the delete button will delete the selected lease table from dhcp lease table. Dns relay select dns relay, the default is enable. Click the apply button to become effective. Notice: 1）the size of lease table can not be larger than the quantity of c network ip ...

  • Page 31

    - 31 - server set sntp server ip address. Time zone select the time zone according to your location. Time out set the time out, the default is 60 seconds. 12 hours systems swich the time mechanism between 12 hours and 24 hours. Default is 24 hours mode sntp select the sntp, and click apply to make t...

  • Page 32

    - 32 - sip config field name explanation choose line to set info about sip, there are 5 lines to choose. You can switch by 【load】 button. Register status shows if the phone has been registered the sip server or not; or so, show unapplied; server name set the server name..

  • Page 33

    - 33 - server address input your sip server address. Server port set your sip server port. Account name input your sip register account name. Password input your sip register password. Phone number input the phone number assigned by your voip service provider. Phone will not register if there is no ...

  • Page 34

    - 34 - enable prack enable or disable sip prack function, suggest use the default config. Long contact set more parameters in contact field; connection with sem server enable uri convert convert # to %23 when send the uri. Dial without register set call out by proxy without registration; ban anonymo...

  • Page 35

    - 35 - patckets sent from server， phone will use the source ip address, not the address in via field. Enable gruu set to support gruu enable displayname quote set to make quotation mark to displayname as the phone sends out signal, in order to be compatible with server. 4.3.3.2. Iax2 config iax2 con...

  • Page 36

    - 36 - refresh time set expire time of iax2 server register, you can set it between 60 and 3600 seconds. Enable register start to register the iax2 server or not by selecting it or not. Enable g.729 enable or disable code g.729 by selecting it or not 4.3.3.3. Stun config in this web page, you can co...

  • Page 37

    - 37 - stun server port set your sip stun server port stun effect time set stun effective time. If nat server finds that a nat mapping is idle after time out, it will release the mapping and the system need send a stun packet to keep the mapping effective and alive. Local sip port set the sip port. ...

  • Page 38

    - 38 - dial peer field name explanation phone number there are two types of matching conditions: one is full matching, the other is prefix matching. In the full matching, you need input your desired phone number in this blank, and then you need dial the phone number to realize calling to what the ph...

  • Page 39

    - 39 - 4) rep: it means that phone will replace the number with length and number appointed. You can refer to the following examples of different alias application to know more how to use different aliases and this dial rule. Call mode select differenct signal protocol, sip or iax2 suffix set suffix...

  • Page 40

    - 40 - this setting will realize speed dial function, after you dialing the numeric key “2”, the number after all will be sent out. When you dial “2”, the sip1 server will receive 33334444 the phone will automatically send out alias number adding your dialed number, if your dialed number starts with...

  • Page 41

    - 41 - dsp configuration field name explanation first codec the fist preferential dsp codec: g.711a/u, g.722, g.723, g.729 second codec the second preferential dsp codec: g.711a/u, g.722, g.723, g.729 third codec the third preferential dsp codec: g.711a/u, g.722, g.723, g.729 forth codec the forth p...

  • Page 42

    - 42 - call service field name explanation hotline specify hotline number. If you set the number, you can not dial any other numbers. No answer time specify no answer time p2p ip prefix set prefix in peer to peer ip call. For example: what you want to dial is 192.168.1.119, if you define p2p ip pref...

  • Page 43

    - 43 - record beyond its set value, the phone will remind the caller to record. Incoming record playing select it or not to enable or disable incoming record playing use record server select it or not to enable or disable use record server. Black list set add/delete black list. If user does not want...

  • Page 44

    - 44 - send the prefix and external number totaly to ther server. For example, there is a rule 9,xxxxxxxx in the digital map table. After dialing 9, phone will send the secondary dial tone, user may keep going dialing. After finished, phone will call the number which starts with 9, actually the numb...

  • Page 45

    - 45 - cause 99 to be dialed after 4 seconds. Cause any number started with 9911 to be dialed 4 seconds after dialing ceases. Notice: end with “#”, fixed length, time out and digital map table can be used simultaneously, system will stop dialing and send number according to your set rules. 4.3.4.4. ...

  • Page 46

    - 46 - function key field name explanation contrast set contrast of screen luminance set luminance of screen mwi number set a function key as listening record in server. Select key event in a function key type, and fill f_mwi in the corresponding table. After you set it, you can pick up or handsfree...

  • Page 47

    - 47 - f_cfwd,or f_callers in the corresponding right table. For example: 4.3.5. Maintenance 4.3.5.1. Auto provision auto provision field name explanation current config version show the current config file’s version. Server address set ftp/tftp/http server ip address for auto update. The address ca...

  • Page 48

    - 48 - syslog server receives the messages from clients, and classifies them based on priority and type. Then these messages will be written into log by some rules which administrator can configure. This is a better way for log management. 8 levels in debug information: level 0---emergency: this is ...

  • Page 49

    - 49 - config setting field name explanation save config you can save all changes of configurations. Click the save button, all changes of configuration will be saved, and be effective immediately. . Backup config right clicks on “right click here…” and select “save target as….” then you will save t...

  • Page 50

    - 50 - update field name explanation web update click the browse button, find out the config file saved before or provided by manufacturer, download it to the phone directly, press “update” to save. You can also update downloaded update file, logo picture, ring, mmiset file by web. Server set the ft...

  • Page 51

    - 51 - account configuration field name explanation keyboard password set the password for entering the setting menu of the phone by the phone ‘s key board. The password is digit. This table shows the current user existed. User name set account user name. User level set user level, root user has the...

  • Page 52

    - 52 - if you modified some configurations which need the phone’s reboot to be effective, you need click the reboot, then the phone will reboot immediately. Notice: before reboot, you need confirm that you have saved all configurations.. 4.3.6. Security 4.3.6.1. Mmi filter mmi filter user could make...

  • Page 53

    - 53 - notice: do not set your visiting ip outside the mmi filter range, otherwise, you can not logon through the web. 4.3.6.2. Firewall firewall configuration in this web interface, you can set up firewall to prevent unauthorized internet users from accessing private networks connected to the inter...

  • Page 54

    - 54 - in_access enable select it to enable in_ access rule out_access enable select it to enable out_ access rule input/output specify current adding rule by selecting input rule or output rule. Deny/permit specify current adding rule by selecting deny rule or permit rule. Protocol type filter prot...

  • Page 55

    - 55 - dmz config： in order to make some intranet equipments support better service for extranet, and make internal network security more effectively, these equipments open to extranet need be separated from the other equipments not open to extranet by the corresponding isolation method according to...

  • Page 56

    - 56 - nat configuration field name explanation ipsec alg it is an encryption technology. Select it to enable ipsec alg, the default is enable ftp alg ftp is a service of connection layer which can transform intranet ip into extranet ip when intranet ip is sending out packet. Select it to enable ftp...

  • Page 57

    - 57 - outside port set the wan port of the nat mapping notice: after finish setting, click the add button to add new mapping table; click the delete button to delete the selected mapping table. Shows the outside wan port ip address and the inside lan port ip address. Outside ip set the outside wan ...

  • Page 58

    - 58 - vpn configuration field name explanation vpn ip shows the current vpn ip address select udp tunnel (vpn tunnel) or vpn l2tp. You can choose only one for current state. After you select it, you’d better save configuration and reboot your phone. Enable vpn select it or not to enable or disable ...

  • Page 59

    - 59 - click logout，and you will exit web page. If you want to enter it next time, you need input user name and password again. 4.4. Configuration via keypad 4.4.1. Keypad introduction user can do brose, modify or cancel via screen menu by using , and soft1/soft2/soft3 z use and soft1 to select the ...

  • Page 60

    - 60 -.

  • Page 61: 5. Appendix

    - 61 - 5. Appendix 5.1. Specification 5.1.1. Hardware item fv6030 adapter (input/output) input: 100-240v output: 5v 1a or poe(802.3af，optional) port wan 10/100base- t rj-45 for lan lan 10/100base- t rj-45 for pc power consumption idle: 2.0w/active: 2.3w lcd size 128*64 dot matrix lcd operation tempe...

  • Page 62: 1 @

    - 62 - z support path, gruu z support srtp z support sip privacy 5.1.3. Network features z wan/lan: support bridge and router model z support pppoe for xdsl z support basic nat and napt z support dhcp client on wan z support dhcp server on lan z support main dns and secondary dns server z support vl...