1. DL manuals
  2. Fanvil
  3. Intercom System
  4. i31S
  5. User Manual

Fanvil i31S User Manual

Other manuals for i31S: Quick Installation Manual
Manual is about: SIP Video DoorPhone

Summary of i31S

  • Page 1

    [键入文字] i31s sip video doorphone user manual v1.0

  • Page 2

    [键入文字] document ver firmware ver explanation time v1.0 2.1.1.2898 initial issue 20170629.

  • Page 3: Safety Notices

    [键入文字] safety notices 1. Please use the specified power adapter. If you need to use the power adapter provided by other manufacturers under special circumstances, please make sure that the voltage and current provided is in accordance with the requirements of this product, meanwhile, please use the ...

  • Page 4: Directory

    [键入文字] directory i product introduction .................................................................................................................... 6 1. A ppearance of the product ..................................................................................................................

  • Page 5

    [键入文字] b) audio ......................................................................................................................................... 32 c) video .........................................................................................................................................

  • Page 6: I  Product Introduction

    [键入文字] 6 / 54 i product introduction i31s voice access is a full digital network door phone, with its core part adopts mature voip solution (broadcom chip), stable and reliable performance, hands‐free adopting digital full‐duplex mode, voice loud and clear, generous appearance, solid durable, easy f...

  • Page 7: Ii Start Using

    [键入文字] 7 / 54 lock status door unlocking: on door locking: off call status standby: off call holding: blink with 1s calls: on ring status standby: off ringing: on network/sip registration network error: blink with 1s network running: off registration failed: blink with 3s registration succeeded: on ...

  • Page 8

    [键入文字] 8 / 54 【note】 when the device is in active mode, it can drive 12v/700ma switch output maximum, to which a standard electric‐lock or another compatible electrical appliance can be connected.  when using the active mode, it is 12v dc in output.  when using the passive mode, output is short co...

  • Page 9: 2.  Quick Setting

    [键入文字] 9 / 54 √ √ 2. Quick setting the product provides a complete function and parameter setting. Users may need to have the network and sip protocol knowledge to understand the meaning represented by all parameters. In order to let equipment users enjoy the high quality of voice service and low co...

  • Page 10: Iii  Basic Operation

    [键入文字] 10 / 54 iii basic operation 1. Answer a call when a call comes in, the device will answer automatically. If you cancel auto answer feature and set auto answer time, you will hear the bell ring at the set time and the device will auto answer after a timeout. 2. Call configure shortcut key as h...

  • Page 11: Iv Page Settings

    [键入文字] 11 / 54 high‐frequency short chirp. When door has been opened, the device will play sirens sound to prompt. Iv page settings 1. Browser configuration when the device and your computer are successfully connected to the network, enter the ip address of the device on the browser as http://xxx.Xx...

  • Page 12

    [键入文字] 12 / 54 3. Configuration via web (1) system a) information information field name explanation system information display equipment model, hardware version, software version, uptime, last uptime and meminfo. Network shows the configuration information for wan port, including connection mode of...

  • Page 13

    [键入文字] 13 / 54 b) account through this page, user can add or remove users depends on their needs and can modify existing user permission. Account field name explanation change web authentication password you can modify the login password to the account add new user you can add new user user accounts...

  • Page 14

    [键入文字] 14 / 54 c) configurations configurations field name explanation export configurations save the equipment configuration to a txt or xml file. Please note to right click on the choice and then choose “save link as.” import configurations browse to the config file, and press update to load it to...

  • Page 15

    [键入文字] 15 / 54 e) auto provision auto provision field name explanation common settings current configuration version show the current config file’s version. If the version of configuration downloaded is higher than this, the configuration will be upgraded. If the endpoints confirm the configuration ...

  • Page 16

    [键入文字] 16 / 54 save auto provision information save the auto provision username and password in the phone until the server url changes dhcp option option value the equipment supports configuration from option 43, option 66, or a custom dhcp option. It may also be disabled. Custom option value custom...

  • Page 17

    [键入文字] 17 / 54 f)fdms fdms settings enable fdms enable/disable fdms configuration fdms interval the time to send sip subscribe information to the fdms server on a regular basis. Unit seconds doorphone info settings community name the name of the community where the device is installed building numbe...

  • Page 18

    [键入文字] 18 / 54 syslog is a protocol used to record log messages using a client/server mechanism. The syslog server receives the messages from clients, and classifies them based on priority and type. Then these messages will be written into a log by rules which the administrator has configured. There...

  • Page 19

    [键入文字] 19 / 54 (2) network a) basic field name explanation network status ip the current ip address of the equipment subnet mask the current subnet mask default gatewaythe current gateway ip address mac the mac address of the equipment mac timestamp get the mac address of time. Settings select the a...

  • Page 20

    [键入文字] 20 / 54 secondary dns server enter the server address of the secondary dns . After entering the new settings, click the apply button. The equipment will save the new settings and apply them. If a new ip address was entered for the equipment, it must be used to login to the phone after clickin...

  • Page 21

    [键入文字] 21 / 54.

  • Page 22

    [键入文字] 22 / 54 field name explanation vpn ip address shows the current vpn ip address. Vpn mode enable vpn enable/disable vpn. L2tp select layer 2 tunneling protocol openvpn select openvpn protocol. (only one protocol may be activated. After the selection is made, the configuration should be saved a...

  • Page 23

    [键入文字] 23 / 54.

  • Page 24

    [键入文字] 24 / 54 sip field name explanation basic settings (choose the sip line to configured) line status display the current line status at page loading. To get the up to date line status, user has to refresh the page manually. Username enter the username of the service account. Display name enter t...

  • Page 25

    [键入文字] 25 / 54 response single codec if setting enabled, the device will use single codec in response to an incoming call request ring type set the ring tone type for the line conference type set the type of call conference, local=set up call conference by the device itself, maximum supports two rem...

  • Page 26

    [键入文字] 26 / 54 enable session timer set the line to enable call ending by session timer refreshment. The call session will be ended if there is not new session timer event update received after the timeout period session timeout set the session timer timeout period enable rport set the line to add r...

  • Page 27

    [键入文字] 27 / 54 basic settings field name explanation sip settings local sip port set the local sip port used to send/receive sip messages. Registration failure retry interval set the retry interval of sip registration when registration failed. Enable strict ua match enable or disable strict ua match...

  • Page 28

    [键入文字] 28 / 54 binding period stun blinding period – stun packets are sent at this interval to keep the nat mapping active. Sip waiting time waiting time for sip. This will vary depending on the network. Tls certification file upload or delete the tls certification file used for encrypted sip transm...

  • Page 29

    [键入文字] 29 / 54 destination configure the destination address and, if configured as a point‐to‐point call, write the peer ip address directly. Can also be set to domain name, by the device dns server to resolve the specific ip address. If it is not configured, the ip address is 0.0.0.0. This is an op...

  • Page 30

    [键入文字] 30 / 54 features field name explanation common settings switch mode monostable: there is only one fixed action status for door unlocking. Bistable: there are two actions and statuses, door unlocking and door locking. Each action might be triggered and changed to the other status. After change...

  • Page 31

    [键入文字] 31 / 54 enable card reader enable or disable card reader for rfid cards. Card reader working mode set id card stats: normal: this is the work mode, after the slot card can to open the door. Card issuing: this is the issuing mode, after the slot card can to add id cards. Card revoking: this is...

  • Page 32

    [键入文字] 32 / 54 enable auto dial out enable auto dial out auto dial out time set auto dial out time enable auto answer enable auto answer function auto answer timeout set auto answer timeout no answer auto hangup enable automatically hang up when no answer auto hangup timeout configuration in a set t...

  • Page 33

    [键入文字] 33 / 54 audio setting field name explanation first codec the first codec choice: g.711a/u, g.722, g.723.1, g.726‐32, g.729ab second codec the second codec choice: g.711a/u, g.722, g.723.1, g.726‐32, g.729ab, none third codec the third codec choice: g.711a/u, g.722, g.723.1, g.726‐32, g.729ab,...

  • Page 34

    [键入文字] 34 / 54 c) video this page allows you to set the video capture and video encode. Video field name explanation video capture ircut mode auto: ircut switches according to the actual ambient light level of the camera synchronization: the switching of the ircut is determined by the actual brightn...

  • Page 35

    [键入文字] 35 / 54 dnc threshold in the day / night mode auto option, the color switching black and white threshold is set backlight compensation in front of a very strong background light can see people or objects clearly autofill sensitivity in the environment changes in light and shade, the higher th...

  • Page 36

    [键入文字] 36 / 54 d) mcast it is easy and convenient to use multicast function to send notice to each member of the multicast via setting the multicast key on the device and sending multicast rtp stream to pre‐configured multicast address. By configuring monitoring multicast address on the device, moni...

  • Page 37

    [键入文字] 37 / 54 stream, and keep the current multicast session in state; if it is not enabled, the device will automatically ignore all receiving multicast rtp stream.  web settings: the multicast ss priority is higher than that of ee, which is the highest priority. Note: when pressing the multicast...

  • Page 38

    [键入文字] 38 / 54  the purpose of setting monitoring multicast "group 1" or "group 2" or "group 3" launched a multicast call.  all equipment has one or more common non multicast communication.  when you set the priority for the disable, multicast any level will not answer, multicast call is rejected...

  • Page 39

    [键入文字] 39 / 54 e) action url action url event settings url for various actions performed by the phone. These actions are recorded and sent as xml files to the server. Sample format is http://internalserver /filename.Xml f) time/date.

  • Page 40

    [键入文字] 40 / 54 time/date field name explanation network time server settings time synchronized via sntp enable time‐sync through sntp protocol time synchronized via dhcp enable time‐sync through dhcp protocol primary time server set primary time server address secondary time server set secondary tim...

  • Page 41

    [键入文字] 41 / 54 hour end the dst end hour manual time settings the time set by hand, need to disable sntp service first. Daylight saving time settings (5) egs access egs access field name explanation import access table.

  • Page 42

    [键入文字] 42 / 54 click the to choose to import remote access list file (access list.Csv) and then clicking can batch import remote access rule. Access table according to entrance guard access rules have been added, you can choose single or multiple rules on this list to delete operation. Add access ru...

  • Page 43

    [键入文字] 43 / 54 type: issuer and revocation when entrance guard is in normal state, swipe card (issuing card) would make entrance guard into the issuing state, and then you can swipe a new card, which the card would be added into the database; when you swipe the issuing card again after cards added d...

  • Page 44

    [键入文字] 44 / 54 number. 3. If the opening door way is local access, there is no display information. Type open type: 1. Local, 2. Remote, 3. Brush card (temporary card, valid card and illegal card). Note: there are three kinds of brushing card feedback results. 1. Temporary card (only added ) the car...

  • Page 45

    [键入文字] 45 / 54  hot key you might enter the phone number in the input box. When you press the shortcut key, equipment would dial preset telephone number. This button can also be used to set the ip address: you can press the shortcut key to directly make a ip call. Type number line subtype usage hot...

  • Page 46

    [键入文字] 46 / 54  operation mechanism you can define the dss key configuration with multicast address, port and used codec. The device can configure via web to monitor the multicast address and port. When the device make a multicast, all devices monitoring the address can receive the multicast data. ...

  • Page 47

    [键入文字] 47 / 54 trigger mode when choosing the low level trigger (closed trigger), detect the input port 1 (low level) closed trigger. When choosing the high level trigger (disconnected trigger), detect the input port 1 (high level) disconnected trigger. Alert message send to server set the alert mes...

  • Page 48

    [键入文字] 48 / 54 alarm command when detected someone tampering the equipment, will be sent alarm to the corresponding server reset command when the equipment receives the command of reset from server, the equipment will stop alarm reset alerting status directly stop the alarm from equipment in the web...

  • Page 49: V  Appendix

    [键入文字] 49 / 54 v appendix 1. Technical parameters communication protocol sip 2.0(rfc‐3261) main chipset broadcom keys dss key 1 (stainless steel) numerickeyboard support audio mic 1 speaker 3w/4Ω volume control adjustable full duplex speakerphone support (aec) speech flow protocols rtp decoding g.72...

  • Page 50: 2.  Basic Functions

    [键入文字] 50 / 54 2. Basic functions  2 sip lines  poe enabled  full‐duplex speakerphone (hf)  numeric keypad (dial pad or password input)  intelligent dss keys (speed dial/intercom etc)  wall mounted / in‐wall  integrated rfid card reader  1 indoor switch interface  1 electric lock relay  an...

  • Page 51: Vi Other Instructions

    [键入文字] 51 / 54 vi other instructions 1. Open door modes  local 1) local password  set (the default is "6789") via door phone\door phone as above.  use the device's keypad to input password and "#" key, then the door will be unlocked. 2) private access code  set and enable local authentication. ...

  • Page 52

    [键入文字] 52 / 54 1) add input a card’s id, selected in the types and clicked , you can add issuer admin card. 2) add input a card’s id, selected in the types and clicked , you can add revocation admin card. 3) administrator table  delete administrator select the admin card of need to delete, click . ...

  • Page 53

    [键入文字] 53 / 54 5) click , card reader would be back to the normal status. 6) the issuing records can be found from the access table list. Method 2: used to add cards for professionals 1) use to touch card reader induction area, and it would be entered issuing card status. 2) use new card to touch ca...

  • Page 54

    [键入文字] 54 / 54  delete user cards method 1: used to batch delete cards for starters. 1) in web page option, select . 2) click , card reader would be entered the revoking status. 3) use card to touch card reader induction area, and you might hear the card reader confirmed indication tone. Repeat ste...