1. DL manuals
  2. FARGO Electronics
  3. Printer
  4. HDP600
  5. User Manual

FARGO Electronics HDP600 User Manual

Manual is about: High Definition Card Printer/Encoder

Summary of HDP600

  • Page 1

    Hdp600 high definition card printer/encoder user guide (rev. 2.3) hdp600 (dual-sided card printer/encoder) hdp600-lc (dual-sided card printer/encoder) hdp600 cr100 (dual-sided card printer/encoder) hdp600-lc cr100 (dual-sided card printer/encoder) part number: l000444.

  • Page 2

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) ii hdp600 high definition card printer/encoder user guide (rev. 2.3), property of fargo electronics, incorporated copyright 2003 by fargo electronics, incorporated. All rights reserved. Prin...

  • Page 3: Table Of Contents

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) iii table of contents section 1: printer overview _________________________________________________ 1-1 how to use the guide _________________________________________________________________...

  • Page 4

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) iv installation procedures ______________________________________________________________ 3-32 installing the hdp600 printer driver _________________________________________________ 3-32 pri...

  • Page 5

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) v using the clear changes button _____________________________________________________ 5-25 using the tcp/ip page ______________________________________________________________ 5-26 using th...

  • Page 6

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) vi installing printer driver updates ____________________________________________________ 7-10 setting up the printer driver__________________________________________________________ 7-11 se...

  • Page 7

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) vii adjusting the transfer dwell time and transfer temperature _____________________________ 7-71 selecting the sensors button and defaults button________________________________________ 7-7...

  • Page 8

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) viii section 12: firmware updates ______________________________________________ 12-1 firmware updater application program _________________________________________________ 12-1 downloading ...

  • Page 9: How To Use The Guide

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-1 section 1: printer overview how to use the guide the hdp600 high definition card printer/encoder user guide (rev. 2.3) is designed to provide installers and technicians with quick, effic...

  • Page 10

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-2 safety messages (review carefully) symbol critical instructions for safety purposes danger: failure to follow these installation guidelines can result in death or serious injury. Informa...

  • Page 11: Hdp600 Overview

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-3 hdp600 overview reviewing the hdp600 block diagram the hdp600 block diagram will be created and added to this service document at a future date. Motors sensors parts 1 card input 13 ther...

  • Page 12

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-4 reviewing the hdp600 sequence of operations the following sequence describes a dual sided full color print job with magnetic encoding. (note: the hdp625/625-lc printers have two (2) card...

  • Page 13

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-5 reviewing hdp 600 series card printer - sequence of operations (continued) step process 12 the fan turns on as required to keep head cool. 13 the ribbon drives, film drive and print plat...

  • Page 14

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-6 reviewing hdp 600 series card printer - sequence of operations (continued) step process 23 the film/ribbon drives and print platen stepper turn on to advance the printed portion of the f...

  • Page 15

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-7 reviewing the hdp600 boot up sequence step process 1 the card feed stepper turns on (to check for a card on the flipper table). 2 the lam headlift turns until the head up position is ret...

  • Page 16

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-8 reviewing the lamination module sequence of operations the lam sequence of operations begins after printing has occurred with the card printer. Step process 1 the card is fed onto the la...

  • Page 17

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-9 reviewing the lamination module sequence of operations (continued) step process 6 the card feed motor and the lamination ribbon motor activate for the length of the card. 7 the laminatio...

  • Page 18

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 1-10 reviewing the lamination module boot up sequence step process 1 the lamination headlift turns until the head up position is returned from headlift sensor. 2 the lamination ribbon motor ...

  • Page 19: Section 2: Specifications

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-1 section 2: specifications the purpose of this section is to provide the user with specific information on the regulatory compliances, agency listings, technical specifications and functi...

  • Page 20

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-2 safety messages (review carefully) symbol critical instructions for safety purposes danger: failure to follow these installation guidelines can result in death or serious injury. Informa...

  • Page 21: Introduction

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-3 introduction the purpose of this section is to provide the user with specific information on the regulatory compliances, agency listings, technical specifications and functional specific...

  • Page 22

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-4 reviewing the hdp600 package these items are included with your hdp600: unpacking instructions and training video cd software installation cd (includes printer driver) cleaning roller as...

  • Page 23

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-5 reviewing the hdp600 cr100 card printer display a – hdp600 cr100 printer with detached output hopper display b – hdp600 cr100 printer with attached output hopper.

  • Page 24: Hdp600 - Agency Listings

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-6 hdp600 - regulatory compliances term description csa (cul) the printer manufacturer has been authorized by ul to represent the card printer as csa certified under csa standard c22.2 no. ...

  • Page 25: Technical Specifications

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-7 technical specifications term description accepted standard card sizes hdp600 and hdp600-lc (see card tab under printer adjustments): cr-80: this selection is the default form size for t...

  • Page 26

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-8 technical specifications (continued) term description accepted card thickness .030 in. (30 mil) to .070 in. (70 mil) (.762mm to 1.778mm). (.030 to .040/.762mm to 1.02mm if laminating wit...

  • Page 27

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-9 technical specifications (continued) term description dimensions hdp600: 15 ” h x 26.1 ” w x 14 ” d/381mm h x 663mm w x 356mmd hdp600-lc: 15 ” h x 34.75 ” w x 14 ” d/381mm h x 883mm w x ...

  • Page 28

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-10 technical specifications (continued) term description fargo certified supplies fargo card printer/encoder require highly specialized media to function properly. To maximize printed card...

  • Page 29

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-11 technical specifications (continued) term description memory 8 mb ram; expandable to 32 mb ram operating temperature 65 º f to 80 º f (18 º c to 27 º c). Options the options are the 32m...

  • Page 30

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-12 technical specifications (continued) term description print ribbon options hdp600 and hdp600-lc: full color, ymc, 700 prints full color with resin black, ymck, 250 or 500 prints full co...

  • Page 31

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-13 technical specifications (continued) term description resolution 300 dpi (11.8 dots/mm) software drivers windows ® 2000/xp supply frequency 50 hz / 60 hz supply voltage 100 to 240 vac, ...

  • Page 32: Functional Specifications

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-14 functional specifications the card printer utilizes two different, yet closely related printing technologies to achieve its remarkable print quality for dye-sublimation and resin therma...

  • Page 33

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-15 printer components: resin thermal transfer to usb interface port component description resin thermal transfer resin thermal transfer is the print method the printer uses to print sharp ...

  • Page 34

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-16 printer components: resin thermal transfer to usb interface port (continued) component description scroll buttons used to scroll through menus and sub-menus and to adjust certain menu o...

  • Page 35

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-17 printer components: lcd and softkey control pad the printer provides a four line, eighty (80) character lcd displays that can communicate helpful information about the printer's operati...

  • Page 36

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-18 printer components: lcd and softkey control pad (continued) component description ready / printer open screens once the printer has finished its system check and with the printer closed...

  • Page 37

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-19 printer components: lcd and softkey control pad (continued) component description print status screen during operation, the lcd will indicate the current print status by showing you the...

  • Page 38

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-20 printer components: lcd and softkey control pad (continued) component description the pause button use this button to pause the printer at any time during operation. Note the printer wi...

  • Page 39

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-21 printer components: lcd and softkey control pad (continued) component description error/attention screens the printer is capable of communicating two similar yet different types of mess...

  • Page 40

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-22 printer components: print ribbons the card printer utilizes both dye-sublimation and/or resin thermal transfer methods to print images (print to film and transfer film to card). Since t...

  • Page 41

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-23 printer components: blank cards caution: never run cards with a contaminated, dull or uneven surface through the printer. Printing onto such cards will ultimately lead to poor print qua...

  • Page 42

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-24 printer components: card input and output hoppers type description card input hopper the card input hopper is where cards are initially loaded for printing. Your printer's hopper provid...

  • Page 43

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-25 printer components: card output hopper and reject hopper type description card output hopper hdp600/hdp-lc and hdp600 cr100/hdp600-lc cr100: all standard hdp card printers provide a 100...

  • Page 44

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-26 printer unit: reviewing the card lamination module danger: the printer ’ s lamination roller can reach temperatures exceeding 350 ° f (175 ° c). Use extreme caution when operating the l...

  • Page 45

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-27 printer components: transfer roller danger: the printer ’ s transfer roller can reach temperatures exceeding 350 degree f (175 c). Use extreme caution when operating the transfer roller...

  • Page 46

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-28 reviewing the overlaminates important! Fargo card printers require highly specialized overlaminates to function properly. To maximize printer life, reliability, printed card quality and...

  • Page 47

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 2-29 reviewing the cr-90 or cr-100 patch size term description cross reference cr-90 or cr-100 polyguard overlaminate is available in a standard cr-80 patch size as well as a cr- 90 and cr-1...

  • Page 48: Table Of Contents

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-1 section 3: installation procedures table of contents section 3: installation procedures ____________________________________________ 3-1 table of contents _______________________________...

  • Page 49

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-2 installing the hdp600 printer driver (cont.)_________________________________________ 3-44 installing the printer driver (windows xp only) (cont.) _______________________________ 3-45 in...

  • Page 50

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-3 safety messages (review carefully) symbol critical procedures for safety purposes danger: failure to follow these installation guidelines can result in death or serious injury. Informati...

  • Page 51: Introduction

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-4 introduction important: the procedures in this section apply for the hdp600/hdp600-lc and hdp600 cr100/hdp600-lc cr100. The following guide will walk you through the installation of the ...

  • Page 52

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-5 choosing a good location follow these guidelines: place the unit in a location with adequate air circulation to prevent internal heat build-up. Use the printer's dimensions as a guidelin...

  • Page 53: Printer Loading Procedures

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-6 printer loading procedures loading the print ribbon note: fargo card printers require highly specialized supplies to function properly. To maximize printer life, reliability, printed car...

  • Page 54

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-7 loading the print ribbon (cont.) display b – loading the print ribbon (supply spool). (note: the print ribbon comes wound on a gray spool with an orange ring around one side. Match the o...

  • Page 55

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-8 loading the print ribbon (cont.) display c – loading the print ribbon (take-up spool).

  • Page 56

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-9 loading the print ribbon (cont.) display d – the print ribbon is shown successfully installed below..

  • Page 57

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-10 loading clear hdp film into the transfer station step procedure 1 caution: ensure that the printer is turned off and the power cord is unplugged from the printer. 2 load the hdp film in...

  • Page 58

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-11 loading clear hdp film into the transfer station (continued) display b – loading the hdp film (take-up spool)..

  • Page 59

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-12 loading clear hdp film into the transfer station (continued) display c – loading the hdp film (take-up spool)..

  • Page 60

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-13 inserting the card cleaning cartridge step procedure 1 load the card cleaning cartridge, as shown in the three (3) photos (displays a to c) in this section. Display a – removing the whi...

  • Page 61

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-14 inserting the card cleaning cartridge (cont.) display b – inserting the card cleaning cartridge.

  • Page 62

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-15 inserting the card cleaning cartridge (cont.) display c – pressing down on the cleaning cartridge until it snaps into place..

  • Page 63

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-16 loading the overlaminate (note: this procedure only applies to the hdp600-lc laminating card printer/encoder.) the loading process for both the thermal transfer film and the polyguard ™...

  • Page 64

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-17 loading the overlaminate (continued) step procedure 4 place the supply end of the overlaminate roll in between the two black lamination drive hubs. Use the end of the supply roll with t...

  • Page 65

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-18 loading the overlaminate (cont.) step procedure 5 load the take-up end of the roll just as you loaded the supply end. (note: when loaded properly, the overlaminate material should feed ...

  • Page 66

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-19 loading the overlaminate (continued) step procedure 6 close the lamination arm by pressing down on the center of the lamination arm until it snaps into place, as shown below. Caution: d...

  • Page 67

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-20 loading the overlaminate (cont.) step procedure 7 to complete this section, close the lamination module cover. Display d – the lamination module is shown with the overlaminate properly ...

  • Page 68

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-21 connecting power to the hdp600 printer caution: do not remove the red warning sticker across the usb connection. Do not plug in the usb cable until prompted to do so during the installa...

  • Page 69

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-22 connecting power to the hdp600 printer (cont.) display b - connecting the ac power cable to the power supply..

  • Page 70

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-23 connecting power to the hdp600 printer (cont.) display c - connecting the other end of the ac power cable to a surge protector. See both notes below. Note no. 1: instead of connecting t...

  • Page 71

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-24 connecting power to the hdp600 printer (cont.) display d - connecting the plug from the power supply to the printer as shown below. (note: if working with a non-lamination unit, proceed...

  • Page 72

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-25 connecting power to the hdp600 printer (cont.) this applies to the hdp600-lc printer only. Display e - connecting the ac power cable to the card lamination power supply..

  • Page 73

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-26 connecting power to the hdp600 printer (cont.) this applies to the hdp600-lc printer only. Display f - connecting the other end of the ac power cable to a surge protector. See both note...

  • Page 74

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-27 connecting power to the hdp600 printer (cont.) this applies to the hdp600-lc printer only. Display g - connecting the plug from the power supply to the card lamination module, as shown ...

  • Page 75

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-28 connecting power to the hdp600 printer (cont.) display h – displays the printer power switch (on/off). Note no. 1: turn on the printer ’ s power by pressing on the power switch. Note no...

  • Page 76

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-29 loading the blank cards step procedure 1 load the blank cards, as shown in the three (3) photos (displays a to c) in this section. Display a – setting the card thickness adjustment leve...

  • Page 77

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-30 loading the blank cards (cont.) display b – loading the blank cards into the empty hopper. Note no. 1 (hdp600 and hdp600-lc only): cycle between hopper 1 and hopper 2 by selecting h1 or...

  • Page 78

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-31 loading the blank cards (cont.) display c – inserting the card weight (push to the back)..

  • Page 79: Installation Procedures

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-32 printer driver installation procedures installation procedures installing the hdp600 printer driver step procedure 1 close down all programs and insert the software installation cd into...

  • Page 80

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-33 installing the hdp600 printer driver (cont.) display a - select hdp600 card printer/encoder (below).

  • Page 81

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-34 installing the hdp600 printer driver (cont.) display b - please wait during installation.

  • Page 82

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-35 installing the hdp600 printer driver (cont.) step procedure 2 click on the next button to continue with the installation..

  • Page 83

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-36 installing the hdp600 printer driver (cont.) step procedure 3 a. Read the license agreement. Select the i accept the terms of the license agreement option. B. Click on the next button t...

  • Page 84

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-37 installing the hdp600 printer driver (cont.) step procedure 4 a. Select the complete option to install the following components: printer driver software printer driver user guide fargo ...

  • Page 85

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-38 installing the printer driver (windows 2000 only) step procedure 5 click on the install button to begin the installation..

  • Page 86

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-39 installing the printer driver (windows xp only) (cont.) step procedure 6 wait during the installation..

  • Page 87

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-40 installing the hdp600 printer driver (cont.) step procedure 7 select local printer attached to this computer if using the printer via usb, and then click the next button. Continue to st...

  • Page 88

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-41 installing the hdp600 printer driver (cont.) step procedure 8 a. Verify that usb is selected from the port list. B. Click the next button..

  • Page 89

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-42 installing the hdp600 printer driver (cont.) step procedure 9 connect the usb cable to both the pc and the printer. Continue to step 11..

  • Page 90

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-43 installing the hdp600 printer driver (cont.) step procedure 10 a. Enter the ip address of the printer. See finding the ip address of the printer in the hdp600 user guide for additional ...

  • Page 91

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-44 installing the hdp600 printer driver (cont.) step procedure 11 click the finish button to complete the fargo add printer wizard..

  • Page 92

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-45 installing the printer driver (windows xp only) (cont.) step procedure 12 select the ribbon type from the dropdown menu. See display a under this procedural step. Or if the ribbon type ...

  • Page 93

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-46 installing the printer driver (windows xp only) (cont.) display a – ribbon type dropdown menu display b – auto ribbon select button.

  • Page 94

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-47 installing the printer driver (windows xp only) (cont.) step procedure 13 a. Click on the finish button to complete the setup, as shown below. B. Click on the install the fargo diagnost...

  • Page 95

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-48 installing the printer driver (windows xp only) (cont.) step procedure 14 wait during the installation of the fargo printer diagnostic utility..

  • Page 96

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-49 installing the printer driver on (windows xp only) (cont.) step procedure 15 click on the yes button to exit the installer, as shown below..

  • Page 97

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-50 installing the printer driver (windows xp only) (cont.) step procedure 16 you have completed this procedure..

  • Page 98

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-51 printing a test print image step procedure 1 a. From your computer ’ s startup menu, select settings > printers and faxes (windows xp) or > printers (windows 2000). B. Double click on t...

  • Page 99

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-52 printing a test print image (cont.) display a - hdp600 printer driver card tab:.

  • Page 100

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-53 printing a test print image (cont.) step procedure 3 this completes the hdp600 high definition card printer/encoder installation guide. For additional help regarding the test print and ...

  • Page 101

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-54 card lamination module installation introduction the following guide provides a step-by-step installation procedure for the hdp600 lamination module and printer driver upgrade. Refer to...

  • Page 102

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-55 inspecting the card lamination module while unpacking your lamination module, inspect the carton to ensure that no damage has occurred during shipping. (note: make sure that all supplie...

  • Page 103: Module

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-56 installing the hdp600 series card lamination module tools needed: #2 phillips screwdriver, torx t-10 screwdriver parts included: card lamination module (d860105), phillips 4-40 flathead...

  • Page 104

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-57 installing the hdp600 series card lamination module (continued) see the previous page. Display b – lam-ready output bin.

  • Page 105

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-58 installing the hdp600 series card lamination module (continued) step description 2 place the lamination module at a slight angle to the printer, as shown below. Continued on the next pa...

  • Page 106

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-59 installing the hdp600 series card lamination module (continued) step description 3 connect the lamination power cable (3-pin connector) to the connector mounted on the hdp sideplate. (n...

  • Page 107

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-60 installing the hdp600 series card lamination module (continued) step description 5 a. Slide the card lamination module (d860105) horizontally to engage the printer or the hdp600 main as...

  • Page 108

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-61 installing the hdp600 series card lamination module (continued) step description 6 a. Fasten the two (2) torx t-10 0.5m3 x 5 screws (f000169) into the rear cover, as shown below. B. Fas...

  • Page 109

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-62 installing the hdp600 series card lamination module (continued) step description 8 insert the driver disk into the cd drive of your pc. (note: refer to the hdp600 high definition card p...

  • Page 110

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-63 installing the printer diagnostic utility step procedure 1 same procedure for the hdp600/hdp600-lc and hdp600 cr100/hdp600- lc cr100. Click on the fargo diagnostics utility install butt...

  • Page 111

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-64 installing the fargo diagnostics utility (cont.) step procedure 2 click on the next button to continue the installation, as shown below..

  • Page 112

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-65 installing the fargo diagnostics utility (cont.) step procedure 3 a. Select the i accept the terms in the license agreement radio button. B. Click on the next button to continue the ins...

  • Page 113

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-66 installing the fargo diagnostics utility (cont.) step procedure 4 a. Enter appropriate user information under the user name: and organization: fields. B. Select the appropriate radio bu...

  • Page 114

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-67 installing the fargo diagnostics utility (cont.) step procedure 5 click on the install button to begin the installation, as shown below..

  • Page 115

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-68 installing the fargo diagnostics utility (cont.) step procedure 6 wait while the files are being copied, as shown below..

  • Page 116

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-69 installing the fargo diagnostics utility (cont.) step procedure 7 click on the finish button to complete the installation, as shown below..

  • Page 117

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-70 printing a test print image step procedure 1 d. From your computer ’ s startup menu, select settings > printers and faxes (windows xp) or > printers (windows 2000). E. Double click on t...

  • Page 118

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 3-71 printing a test print image (continued) step procedure 3 this completes the hdp600 high definition card printer/encoder installation guide. For additional help regarding the test print ...

  • Page 119: Table Of Contents

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-1 section 4: general troubleshooting the purpose of this section is to provide the user with specific procedures relating to the lcd messages, communication errors, card feeding errors, en...

  • Page 120: Lcd Messages

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-2 lcd messages important: the procedures in this section apply for the hdp600/hdp600-lc and hdp600 cr100/hdp600-lc cr100. The lcd display shows the current status of the printer. Refer to ...

  • Page 121

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-3 reviewing lcd messages (continued) message cause solution card jam: lam there is a card jam in the laminator. Clear the jam. Card jam error a card is jammed. Clear the jam. Card jam flip...

  • Page 122

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-4 reviewing lcd messages (continued) message cause solution check ribbon error the print ribbon may be jammed, not installed properly, broken or damaged. Verify the ribbon is installed pro...

  • Page 123

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-5 reviewing lcd messages (continued) message cause solution heater timeout the transfer roller was unable to reach its goal temperature. Turn the printer off and on to reset and try reprin...

  • Page 124

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-6 reviewing lcd messages (continued) message cause solution film sensors are not calibrated. Your film sensors must be calibrated before the film will align properly. Press calibrate to se...

  • Page 125

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-7 reviewing lcd messages (continued) message cause solution head voltage error a hardware fault has prevented setting the correct printhead voltage. A default value will be used. Call for ...

  • Page 126

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-8 reviewing lcd messages (continued) message cause solution lam error the lamination module requires attention. Check the indicated condition and correct using the laminator's control butt...

  • Page 127

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-9 reviewing lcd messages (continued) message cause solution wrong lam type the installed lamination material does not match the material required by the print job. Replace the current mate...

  • Page 128

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-10 reviewing lcd messages (continued) message cause solution communication error the printer is not able to communicate with the host pc. Printer to pc communication has been disabled. Ver...

  • Page 129

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-11 general troubleshooting guide problem possible solution ribbon wrinkle verify the convex roller (d860051) is installed correctly with the shorter notch towards the front of the printer....

  • Page 130

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-12 general troubleshooting guide (continued) problem possible solution ribbon chipping / reverse transfer during printing print density is set too high. Self test is not square adjust the ...

  • Page 131

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-13 general troubleshooting guide (continued) problem possible solution printhead cutting ribbon verify the solder leads on the printhead are trimmed. Replace the printhead cable (840143). ...

  • Page 132

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-14 general troubleshooting guide (continued) problem possible solution input roller continually spins on power up verify the cable (d840687) is plugged into the sensor (840176) and the cir...

  • Page 133

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-15 magnetic and e-card troubleshooting guide problem possible solution start sentinel is yellow or red change the magnetic tof in the lcd according to the start sentinel reference chart ve...

  • Page 134

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-16 magnetic and e-card troubleshooting guide (continued) problem possible solution yellow or red readings on only one track verify wires are not pulling the magnetic head to one side. Insp...

  • Page 135: Printing A Test Image

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-17 printing a test image step procedure 1 choose print test image to select a preset test image. (note: these images help to determine if the printer is functioning properly.) 2 scroll to ...

  • Page 136

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-18 reviewing the color/resin ymck self-test step procedure 1 use this card to determine image placement and confirm that (a) the image colors are properly reproduced and (b) the resin pane...

  • Page 137

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-19 reviewing the card count self-test step procedure 1 use this card to view counts for card count (cc), pass count (pc), transfer count (tc) and lamination count (lc). The card count is t...

  • Page 138

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 4-20 reviewing the lamination color/resin ymck+l self-test step procedure 1 use this card to determine lamination placement and confirm that (a) the image colors are properly reproduced and ...

  • Page 139: Table Of Contents

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-1 section 5: ethernet option section table of contents section 5: ethernet option section ___________________________________________ 5-1 table of contents ________________________________...

  • Page 140

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-2 specifying udp event logging (continued) _________________________________________ 5-37 specifying tcp event logging ______________________________________________________ 5-38 specifyin...

  • Page 141: Introduction

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-3 introduction the ethernet option includes the ethernet port and the internal printer server. Printer management: the printer driver provides bi-directional status information so you can ...

  • Page 142

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-4 functional specification - ethernet option the fargo ethernet option includes these features. Feature description simultaneous printing provides the ability to simultaneously print from ...

  • Page 143

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-5 network services - overview the ethernet option provides the services described in this section. (note: other additional services include a ping client, address assignment and printer di...

  • Page 144

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-6 network management interface the snmp interface is described below. Interface description snmp the ethernet interface is a fully-manageable snmp agent that supports mib-ii. The ethernet ...

  • Page 145

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-7 reviewing the telnet command table the following table describes available telnet commands. (note: you can enter partial full- word commands: the printer will respond with additional hel...

  • Page 146

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-8 reviewing the telnet command table (continued) telnet command command purpose command format all display all information about this printer. List all diff display all differences between...

  • Page 147

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-9 reviewing the telnet command table (continued) telnet command command purpose command format lpq display information about print jobs and their settings. List lpq printer display informa...

  • Page 148

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-10 reviewing the telnet command table (continued) telnet command command purpose command format contact set the contact string. Set sysinfo label [] location set the location string. Set s...

  • Page 149

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-11 reviewing the telnet command table (continued) telnet command command purpose command format add add a new user definition. Up to four (4) users may be defined. Set user add del delete ...

  • Page 150

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-12 reviewing the telnet command table (continued) telnet command command purpose command format addr store a new ip address. Store net addr mask store a new address mask. Store net mask ga...

  • Page 151: Ethernet Web Pages

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-13 reviewing the telnet command table (continued) telnet command command purpose command format save save all current settings as the stored settings in the permanent memory. Save load tak...

  • Page 152: Logging In

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-14 logging in when a user attempts to change any setting, they are asked for a user name and password. (note: the guest users can only view settings.) step procedure 1 enter the correct us...

  • Page 153: Accessing The Home Pages

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-15 accessing the home pages step procedure 1 open a window for your network browser application on your local pc. 2 find the ip address of the printer. (note: see the section accessing the...

  • Page 154

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-16 reviewing the hdp600 home page.

  • Page 155

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-17 reviewing the home page categories and fields (table) you can view these categories and fields in the following table. Category field purpose serial number (print server) displays the u...

  • Page 156

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-18 configuring the network settings the procedures needed to configure the network settings are presented in this section. Accessing the network settings page the network page displays the...

  • Page 157

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-19 reviewing the interface the interface display indicates the network speed supported by the printer..

  • Page 158

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-20 reviewing the current settings the current settings page section displays the current active network settings for the printer. These are also labeled as dynamic if they were provided by...

  • Page 159

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-21 switching to the automatic ip address mode step procedure 1 select the network link from any web page of the printer. 2 select the obtain an ip address automatically radio button to ena...

  • Page 160

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-22 changing to the static ip address mode step procedure 1 select the network link from any web page of the printer. 2 select the use the following ip address radio button, which prepares ...

  • Page 161

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-23 changing to the static ip address mode (continued) step procedure 7 log in as a root user if you are so prompted. (note: any change of setting will only be accepted after you have succe...

  • Page 162

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-24 entering the tcp window size step procedure 1 select the network link from any web page of the printer. 2 select the tcp window size from the drop-down menu, as shown below. This entry ...

  • Page 163

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-25 using the clear changes button step procedure 1 click on the clear changes button to delete the information in the textboxes in stored settings area. See the lower left corner of this d...

  • Page 164: Using The Tcp/ip Page

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-26 using the tcp/ip page the tcp/ip page displays the tcp/ip status of each printer connection, which are not configurable. See the next two pages for displays. Step procedure 1 select the...

  • Page 165

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-27 using the tcp/ip status web page see the using the tcp/ip page procedure..

  • Page 166: Using The Printer Page

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-28 using the printer page you can use the printer page to review current information about the printer device settings and print jobs. Device settings includes the following: the status wh...

  • Page 167

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-29 reviewing the printer page (continued) see the previous page for descriptions of the fields..

  • Page 168

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-30 using the system log page the system log page displays the current system log settings and allows the user to change the settings. (note: these settings configure how system logging occ...

  • Page 169

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-31 changing the log name by default the names are log1 and log2. However, you can rename them from this page. (note: this also updates the link to the corresponding web page.) step procedu...

  • Page 170

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-32 changing the log name (continued) step procedure 2 select the link for the log name you want to view or configure (the default choices are log1 or log2). See the previous page. 3 enter ...

  • Page 171

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-33 selecting the log type step procedure 1 select the system log link. See the next page. 2 select the link for the log name you want to view or configure (the default choices are log1 or ...

  • Page 172

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-34 selecting the log destination specify one destination for the log. Step procedure (no event logging) 1 select the system log link. 2 select the link for the log name you want to view or...

  • Page 173

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-35 setting up email event logging follow this procedure to enable logging using email notification: step procedure (specify email logging) 1 select the system log link. 2 select the link f...

  • Page 174

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-36 specifying udp event logging follow this procedure to enable logging to a udp syslog program. Step procedure 1 select the system log link. The messages will be sent via upd packets to t...

  • Page 175

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-37 specifying udp event logging (continued) step procedure 5 select submit. 6 log in as a root user if you are so prompted. (note: any change of setting will only be accepted after you hav...

  • Page 176

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-38 specifying tcp event logging follow this procedure to send logging messages to a pre-existing ip connection made on the tcp port. Step procedure 1 select the system log link. 2 select t...

  • Page 177

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-39 specifying tcp event logging (continued) step procedure 3 select the tcp connection radio button. 4 select submit. 5 log in as a root user if you are so prompted. Any change of setting ...

  • Page 178

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-40 using the administration pages the purpose of the administration pages is to allow the user to upgrade, reboot, modify passwords and enter user-specified system information strings. Usi...

  • Page 179

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-41 using the system information page (continued) step procedure 5 select the submit button. 6 log in as a root user if you are so prompted. Any change of setting will only be accepted afte...

  • Page 180

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-42 changing the root password the passwords page allows the user to change the passwords needed to log in as a user. Changes to all settings require a login. (note: however, these changes ...

  • Page 181

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-43 changing the root password (continued) step procedure 7 select the submit button. 8 log in as a root user (using the old password) if you are so prompted. (note: any change of setting w...

  • Page 182

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-44 upgrading the print server this procedure provides a means to upgrade the firmware in the printer server not the main printer. Step procedure 1 select the administration link. 2 log in ...

  • Page 183

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-45 upgrading the dtc400 and hdp600 print server (continued) step procedure 6 select the upgrade button to start the firmware upload. 7 select reboot when requested..

  • Page 184: Using The Reboot Pages

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-46 using the reboot pages rebooting the dtc400 and hdp600 restarts only the ethernet print server. Rebooting the ethernet server the reboot page allows the user to restart the ethernet pri...

  • Page 185

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-47 rebooting the ethernet server (continued) step procedure 5 click yes when prompted. 6 wait for the printer to reboot and display the home page..

  • Page 186

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-48 resetting to default settings the reboot page also allows the user to reboot the ethernet print server into a default settings mode. (note: this simply restarts the printer in a differe...

  • Page 187: Using The Help Page

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-49 using the help page the help page displays the help information. Step procedure 1 open this web page at the appropriate location by clicking on the help book icon at the top of each pag...

  • Page 188: Additional Procedures

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-50 additional procedures reviewing led and dipswitch tables the leds and dipswitches can be found on the back of printers. Reviewing the led table led hdp600 position flash rate indicates ...

  • Page 189

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-51 reviewing the dip switches for the dtc400, on means a dipswitch is down and off means a dipswitch is up. For the hdp600, on means a dipswitch is to the left and off means a dipswitch is...

  • Page 190

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-52 restoring the factory settings for ethernet there may be times when you are unable to use the current configuration of the ethernet interface. (note: this could be because you have lost...

  • Page 191

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-53 accessing the ip address of your printer the additional lcd menus for ethernet-enabled printers are provided to view the ip address of the printer. Follow these procedures to access the...

  • Page 192: Diagnostics Utility

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-54 upgrading the main firmware with the fargo diagnostics utility the printer server firmware upgrades for the dtc400/hdp600 are done from the upgrade web page for the printer. See the upg...

  • Page 193

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-55 upgrading the main firmware with the fargo diagnostics utility (continued).

  • Page 194

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-56 ethernet printer troubleshooting procedures troubleshooting procedures if you are having trouble connecting to your ethernet printer or printing to it, you should go through each of the...

  • Page 195

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-57 verifying the printer connection step procedure 1 ensure that your printer has a valid network connection. 3 verify that the printer has both leds blinking on and off with network activ...

  • Page 196

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-58 verifying that your pc can access the printer using the ping command step procedure 1 follow these instructions to issue a ping command to the printer: at a dos prompt, enter ping [ip a...

  • Page 197

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-59 verifying that your pc can access the printer using the ping command (continued) step procedure 2 verify that the pc and the printer are connected to the same network. 3 you may be on d...

  • Page 198

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-60 reviewing frequently-asked questions question answer how do i know if my printer has the ethernet option installed? If your printer has the rj45 connector installed on the back of the p...

  • Page 199

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-61 reviewing frequently-asked questions (continued) question answer how can i find the ip address of my ethernet printer? You can find it in the lcd of the printer if the ethernet option i...

  • Page 200

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-62 reviewing frequently-asked questions (continued) question answer can i use fargo ip-tracer to locate printers on a different network segment? No. The ip-tracer can only locate fargo-com...

  • Page 201

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-63 reviewing frequently-asked questions (continued) question answer what if i lose the password for my printer or it is not accepted? See reviewing the dip switches . Factory default setti...

  • Page 202

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-64 reviewing frequently-asked questions (continued) question answer how can i verify/change what ip address my installed printer driver is expecting to find my printer? Follow this procedu...

  • Page 203

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-65 reviewing frequently-asked questions (continued) question answer how do i choose a static ip address for my ethernet printer? You can use the web pages if you know the current ip addres...

  • Page 204: Glossary Of Terms

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-66 glossary of terms term purpose mac (media access control) the unique numeric value address associated with a network device that gives the device a unique identity. This address is assi...

  • Page 205

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 5-67 glossary of terms (continued) term purpose snmp (simple network management protocol) this is protocol for the network management services. This protocol provides a means for network com...

  • Page 206: Table Of Contents

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 6-1 section 6: card lamination module important: the procedures in this section apply for the hdp600/hdp600-lc and hdp600 cr100/hdp600-lc cr100 card printers. The purpose of this section is ...

  • Page 207

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 6-2 reviewing the card lamination module.

  • Page 208

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 6-3 safety messages (review carefully) symbol critical instructions for safety purposes danger: failure to follow these installation guidelines can result in death or serious injury. Informa...

  • Page 209

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 6-4 opening the card lamination module step procedure 1 open the top cover of the lamination module by lifting up on its bottom edge and tilting it back into its fully open position. (note: ...

  • Page 210

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 6-5 opening the card lamination module (continued) step procedure 2 open the lamination station by lifting up on the blue securing latches. Pull the lamination station up and back into its f...

  • Page 211

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 6-6 adjusting the card lamination module the hdp600 supports the attachment of an optional card lamination module. This module can be ordered pre-installed on the printer from the factory or...

  • Page 212: Table Of Contents

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-1 section 7: printer adjustments important: the hdp600 cr100/hdp600-lc cr100 printers have their own printer driver. However, the majority of the procedures in this section apply for all h...

  • Page 213

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-2 using the disable printing option____________________________________________________ 7-37 using the image color tab (hdp600) ___________________________________________________ 7-38 usi...

  • Page 214

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-3 safety messages (review carefully) symbol critical instructions for safety purposes danger: failure to follow these installation guidelines can result in death or serious injury. Informa...

  • Page 215: Adjusting The Card Size

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-4 important! Fargo card printers require highly specialized print ribbons to function properly. To maximize printer life, reliability, printed card quality and durability, you must use onl...

  • Page 216

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-5 printing on alternate card stocks selecting the right cards and optimize the hdp print process in order to optimize the hdp card printer ’ s capabilities for cards with hard-to-print sur...

  • Page 217

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-6 selecting the appropriate hdp printer driver settings fargo offers two types of pvc cards: glossy ultracard iii ™ cards and matte-finished hdp- pvc cards. Defaults: the hdp printer drive...

  • Page 218

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-7 conducting the tape adhesion test it is important to conduct tape adhesion tests because fargo cannot be certain which transfer temperature and dwell time will work best (when printing c...

  • Page 219

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-8 fail: significant transfer to tape pass: very slight transfer to tape pass: absolutely no transfer to tape 1 2 3 conducting the tape adhesion test (continued).

  • Page 220

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-9 conducting the tape adhesion test (continued) step procedure 4 visually examine the card and the strip of tape pulled from the card, to see if any portion of the hdp film was removed fro...

  • Page 221: Printer Driver Options

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-10 printer driver options installing printer driver updates occasionally, new printer driver versions are released which have new or updated features. Before installing an updated printer ...

  • Page 222

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-11 setting up the printer driver once the appropriate printer driver for the computer has been installed, you will need to set the driver up with the proper print options. To open the prin...

  • Page 223

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-12 using the card tab (hdp600/hdp600-lc) use this option to control specific printer functions..

  • Page 224: Cr100)

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-13 using the card tab (hdp600 cr100/hdp600-lc cr100) step procedure 1 select the appropriate card size option from three (3) standard card sizes. Cr-100 or one (1) custom size is available...

  • Page 225

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-14 selecting the card size (hdp600 and hdp600-lc) step procedure 1 select the appropriate card option: cr-80: this selection is the default form size for the hdp600. This will print a 2.12...

  • Page 226

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-15 selecting the card size (hdp600 and hdp600-lc) (continued) see three previous procedures..

  • Page 227

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-16 selecting the custom card size select the appropriate custom card size according to the dimensions of the card stock. Step procedure 1 a. Select the custom option and enter the dimensio...

  • Page 228

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-17 selecting the card type (all hdp600 printers) select the appropriate card type according to the composition of the card stock. Step procedure 1 select ultracards-glossy pvc if using far...

  • Page 229

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-18 selecting the card type (continued) step procedure 2 if using a card stock other than listed, use the custom 1 and custom 2 options to save custom dwell time and dwell temperature contr...

  • Page 230

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-19 selecting the card hopper (hdp600 and hdp600-lc only) selects the appropriate card hopper step procedure 1 a. Select first available to print from the hopper currently selected as indic...

  • Page 231

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-20 selecting the card hopper (hdp600 cr100 and hdp600-lc cr100 only) there is only one (1) input hopper for one hundred (100) cr100 cards..

  • Page 232

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-21 setting the orientation select either the portrait or landscape radio buttons for orientation. Step procedure 1 select portrait to cause the card to print in a vertical orientation. Or ...

  • Page 233

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-22 selecting the diagnostics button this will launch the diagnostic tool (if installed). Selecting the test print button when selected a file will be copied down to the printer. This file ...

  • Page 234

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-23 selecting the about button select the about button to open a dialog box containing the copyright information as well as the driver ’ s version number and date code..

  • Page 235

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-24 using the device options tab (hdp600/hdp600-lc) the hdp600 printing preferences window is used throughout this section for consistency within this document. See the hdp600 printing pref...

  • Page 236: Hdp600-Lc Cr100)

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-25 using the device options tab (hdp600 cr100/ hdp600-lc cr100) the hdp600 os cr100 printing preferences window has the same device options tab functionality as the hdp600 printing prefere...

  • Page 237

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-26 adjusting the ribbon type use the ribbon type dropdown menu to match ribbon type. Step procedure 1 adjust to match the ribbon type selection with the ribbon type that is loaded in the p...

  • Page 238

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-27 adjusting the film type step procedure 1 allows you to select the film type option that is appropriate for the type of hdp film currently loaded in the printer. Select the clear option ...

  • Page 239

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-28 adjusting for the color matching allows selection of the color matching option that best fits the requirements of the print job. Step procedure 1 select none (a) if interested in print ...

  • Page 240

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-29 adjusting for the color tone – natural or enhanced select the appropriate step procedure 1 this will allow the selection between two different color levels. Natural, the default selecti...

  • Page 241

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-30 adjusting for the resin dither select the appropriate dither method according to the type of image to be printed. (note: this option only affects those objects printed on the backside o...

  • Page 242

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-31 using the print both sides option use this option to automatically print on both the front and backside of a card. Step procedure 1 select this option in conjunction with any applicatio...

  • Page 243

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-32 using the split 1 set of ribbon panels option use this option to provide the most economical means of printing a dual-sided card since a single set of ribbon panels will be split to pri...

  • Page 244

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-33 using the print back side first option step procedure 1 select this option: if you need to print the first page of a two-page document on the backside of the card. Or if you need to pri...

  • Page 245

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-34 using the print back side only option use this option to print only onto the backside of cards. Step procedure 1 select this option to print only onto the backside of preprinted cards t...

  • Page 246

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-35 using the rotate front 180 degrees or rotate back 180 degrees options use this option to change the position of the printed image in relation to the set location of a card's magnetic st...

  • Page 247

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-36 using the print in single card mode option use this option to force the printer's memory to buffer or to hold only one print job at a time. Step procedure 1 select this option only when...

  • Page 248

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-37 using the disable printing option use this option to disable the printing capabilities of the printer while still allowing the printer to encode cards. (note: this option is useful to e...

  • Page 249

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-38 using the image color tab (hdp600) use this tab to adjust color properties. (note: the hdp600 cr100 printing preferences window has the same image color tab functionality as the hdp600 ...

  • Page 250

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-39 using the image color tab (continued) step procedure 2 select the none or monitor option (see the device options tab, shown below) to only display the dye-sub intensity and resin heat s...

  • Page 251

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-40 using the image color tab (continued) step procedure 4 control the amount of heat the printer uses when printing with the resin black panel by adjusting the resin heat slide. Move the s...

  • Page 252

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-41 using the image color tab step procedure 5 as needed, return all options to their factory settings by clicking on the default button..

  • Page 253

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-42 using the image transfer tab use this tab to adjust the image position, transfer dwell time and transfer temperature. (note: the hdp600 cr100 printing preferences window has the same im...

  • Page 254

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-43 adjusting the image position controls use the image position controls to position the image on a card (to be adjusted). Step procedure 1 adjust the image position values by clicking on ...

  • Page 255

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-44 the display (below) represents how the printed image will move in relation to the fixed card position as positive and negative image placement values are entered. Step procedure 2 use t...

  • Page 256

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-45 adjusting the transfer dwell time and temperature use the image transfer option to control of the transfer dwell time and transfer temperature. These settings control the speed and temp...

  • Page 257

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-46 using the k panel resin tab use this tab to adjust the cr-80 card size, the direction the card travels through the printer, the print all black with k panel (options) and the defined ar...

  • Page 258

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-47 selecting the full card with the k panel resin tab step procedure 1 select the full card option to print the resin black (k) panel for all black found within all areas of the image, as ...

  • Page 259

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-48 selecting the defined area(s) with the k panel resin tab step procedure 1 select the defined area(s) option to print the resin black (k) panel for all black found only in an area or are...

  • Page 260

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-49 selecting the undefined area(s) with the k panel resin tab step procedure 1 select the undefined area(s) option to print the resin black (k) panel for all black found only in the space ...

  • Page 261

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-50 defining the area to activate the card grid step procedure 1 select on the appropriate defined area (see below)to activate the card grid in the upper half of the window. It is through t...

  • Page 262

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-51 measuring the total card area step procedure 1 determine the area of the card to define. (note: this area is indicated by the dashed outline, as shown below. The easiest way to determin...

  • Page 263

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-52 measuring the area to be positioned on the card step procedure 1 once the area is sized properly, measure the location where this area is to be positioned on the card. A. Measure from t...

  • Page 264

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-53 selecting the print ymc under the k and print k only options step procedure 1 use the defined area function. A. Define an area by clicking on the defined area up arrow. (note: another ....

  • Page 265

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-54 using the magnetic encoding tab use these options only if the printer has an optional magnetic stripe encoding module installed. (note: the hdp600 cr100 printing preferences window has ...

  • Page 266

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-55 using the encoding mode option use the encoding mode option to specify which magnetic encoding standard to use. The hdp card printer can be installed with one of two types of factory-in...

  • Page 267

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-56 using the encoding mode option (continued) step procedure 1 select the iso standard encoding module with a dual-coercivity (high or low) encoding head. (note: by default, the printer dr...

  • Page 268

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-57 encoding the mode/coercivity/magnetic track selection use the iso option for encoding capability for either high- or low-coercivity cards on tracks 1, 2 and 3 and is the industry's stan...

  • Page 269

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-58 encoding the mode/coercivity/magnetic track selection (continued) use the iso option for encoding capability for either high- or low-coercivity cards on tracks 1, 2 and 3 and is the ind...

  • Page 270

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-59 reviewing the magnetic track options use these options to customize the iso encoded data format for each of the magnetic stripe's three tracks. Step procedure 1 specify which of the thr...

  • Page 271

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-60 reviewing the enable mle support checkbox multi-language extension (mle) support in windows xp can cause text strings to be broken up into fragments. This fragmentation of the text stri...

  • Page 272

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-61 reviewing the verification options use this option, which instructs the printer to verify that all magnetic data has been correctly encoded on each card. (note: with either of these opt...

  • Page 273

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-62 reviewing the shift data left use the shift data left option, which applies to all tracks when selected. Step procedure 1 select this option to shift the recorded magnetic data to the l...

  • Page 274

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-63 reviewing the iso track locations the magnetic encoding module encodes onto tracks in accordance with an iso 7811-2 magnetic stripe. For track locations, review the display below. Track...

  • Page 275

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-64 sending the track information magnetic track data is sent in the form of text strings from the application software to the printer driver. In order for the printer driver to differentia...

  • Page 276

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-65 reviewing the sample string track 1: ~1%julieanderson^1234567890? Track 2: ~2;1234567890987654321? Track 3: ~3;1234567890987654321? Track start sentinel end sentinel field separator val...

  • Page 277

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-66 reviewing the ascii code and character table ascii code character ascii code character ascii code character 32 space 56 8 80 p 33 ! 57 9 81 q 34 58 : 82 r 35 # 59 ; 83 s 36 $ 60 84 t 37...

  • Page 278: Module)

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-67 using the lamination tab (only with card lamination module) use this option to control specific printer functions. These options allow you to control the printer's lamination process. (...

  • Page 279

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-68 selecting the lamination position step procedure 1 the lamination position control allows you to adjust the horizontal position of the polyguard overlaminate. This control functions in ...

  • Page 280

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-69 selecting the lamination side step procedure 1 a. Select the no lamination option if you do not want to use the printer's built-in laminator. B. Select laminate front side, laminate bac...

  • Page 281

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-70 selecting the lamination type step procedure 1 select one of the lamination type options, according to which type of lamination media is currently installed. Two types of overlaminates ...

  • Page 282

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-71 adjusting the transfer dwell time and transfer temperature step procedure 1 adjust the transfer dwell time and the transfer temperature to control the lamination dwell time or through-p...

  • Page 283

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 7-72 selecting the sensors button and defaults button step procedure 1 select the lamination tab's sensors button to display options for calibrating the card lamination module ’ s lamination...

  • Page 284: Section 8: Cleaning

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-1 section 8: cleaning important: the procedures in this section apply for the hdp600/hdp600-lc and hdp600 cr100/hdp600-lc cr100 card printers. This section deals with the printer ’ s inter...

  • Page 285

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-2 using the required supplies for the maintenance procedures outlined for the printer, you will need a printer cleaning kit, available from the reseller. This optional kit includes the fol...

  • Page 286

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-3 safety messages (review carefully) symbol critical instructions for safety purposes danger: failure to follow these installation guidelines can result in death or serious injury. Informa...

  • Page 287

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-4 cleaning inside the printer step procedure 1 open the lamination arm. 2 remove the print ribbon and hdp film from the printer. 3 if you have a can of compressed air, blow out all visible...

  • Page 288

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-5 cleaning the printhead clean the printhead every time the print ribbon is changed to maintain consistent print quality, as instructed below. This procedure should also be performed appro...

  • Page 289

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-6 replacing the card cleaning tape caution: replace the card cleaning tape approximately every 2,000 to 3,000 prints, depending on the cleanliness of the card stock or the environment in w...

  • Page 290

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-7 see the previous procedure in this section..

  • Page 291

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-8 cleaning the magnetic encoder step procedure 1 open the top cover and remove the ribbon. 2 a. Locate the flipper table in the input module. B. Turn the printer on. C. Rotate the flipper ...

  • Page 292

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-9 cleaning the magnetic encoder (continued) step procedure 6 press the rev button on the lcd display seven (7) times to feed the card into the magnetic module. (note: the card does not go ...

  • Page 293

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-10 cleaning the platen and transfer rollers step procedure 1 leave the printer power on and open the lamination arm. If using a printer with a card lamination module attached, also open th...

  • Page 294

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 8-11 cleaning the transfer rollers using the cleaning card step procedure 1 leave the printer power on and open the lamination arm. If using a printer with a card lamination module attached,...

  • Page 295

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 9-12 section 9: packing the card printer important: the procedure in this section apply for the hdp600/hdp600-lc and hdp600 cr100/hdp600-lc cr100 card printers. The purpose of this section t...

  • Page 296: Table Of Contents

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 10-1 section 10: board level diagnostics important: the procedures in this section apply for the hdp600/hdp600-lc and hdp600 cr100/hdp600-lc cr100 card printers. The purpose of this section ...

  • Page 297: Board Errors

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 10-2 board errors resolving the ee memory error symptom: an error has occurred in the permanent circuit memory. (note: the printer ’ s lcd will state the following: eeprom erased.) step proc...

  • Page 298

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 10-3 resolving the dram memory error symptom: an error has occurred in the removable memory module (simm). (note: the lcd will state the following: main memory error.) step procedure 1 reboo...

  • Page 299: Sensor Testing

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 10-4 resolving the fpga error symptom: an unexpected hardware error has occurred. Step procedure 1 reboot the printer. 2 if the problem persists, the main print board will need to be replace...

  • Page 300

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 10-5 reviewing the sensor locations and voltages sensor or switch location low range (vdc) high range (vdc) ribbon supply encoder d860095 j4 pin 12 unblocked (.17 or lower) blocked 3.0 - 3.5...

  • Page 301

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 10-6 reviewing the sensor locations and voltages (continued) ribbon mark sensor 5 d860112 j9 pin 3 blocked (.8 or lower) unblocked +4 mag card sensor d860191 j6 pin 8 covered (.9 or lower) u...

  • Page 302

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 10-7 reviewing the motor locations and cables motor cable location flipper table motor (840124) d860130 j31 flip / feed motor (e000062 & d840861) d860129 j34 card drive stepper (d860138 d860...

  • Page 303: Navigation

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-1 section 11: lcd on-line menu navigation important: the procedures in this section apply for the hdp600/hdp600-lc and hdp600 cr100/hdp600-lc cr100 card printers. The purpose of this sect...

  • Page 304

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-2 selecting from the hdp600 menu option structure tree see appendix a for the two (2) hdp600 menu option structure trees..

  • Page 305

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-3 reviewing the printer setup the printer parameters found in setup printer are preset at the factory and should not need to be changed unless an issue develops. If a change to these sett...

  • Page 306

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-4 reviewing the printer setup (continued) step procedure 3 be sure to run this test after each adjustment. Run the alignment test image by selecting the following options: menu, print tes...

  • Page 307

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-5 preparing to adjust the print offset, transfer tof and transfer eof step procedure 1 before starting the alignment procedures, you must first establish a baseline from which to start th...

  • Page 308

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-6 aligning the print offset this procedure positions the image correctly on the hdp film. Refer to the preparing to adjust the print offset, transfer tof and transfer eof procedure for pr...

  • Page 309

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-7 aligning the print offset (continued) step procedure 6 proceed to adjusting transfer tof to center the image on the card..

  • Page 310

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-8 setting the transfer tof this procedure positions the hdp film correctly on the leading edge of the card. Refer to the preparing to adjust the print offset, transfer tof and transfer eo...

  • Page 311

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-9 setting the transfer tof (continued) step procedure 5 proceed to adjusting transfer eof to center the image on the card..

  • Page 312

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-10 setting the transfer eof this procedure controls the point on the card at which the transfer roller lifts and ceases transfer. Refer to the preparing to adjust the print offset, transf...

  • Page 313

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-11 setting the transfer eof (continued) step procedure 3 determine the amount of transfer eof adjustment needed by using a caliper to measure the “ gap ” . The gap: represents the distanc...

  • Page 314

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-12 using the gap distance table.

  • Page 315

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-13 using the gap distance table (continued).

  • Page 316

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-14 using the gap distance table (continued).

  • Page 317

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-15 adjusting the transfer tension this procedure positions the image correctly on the card. Refer to the preparing to adjust the print offset, transfer tof and transfer eof procedure for ...

  • Page 318

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-16 adjusting the film drive the film drive sets the baseline for the film tension and should not be adjusted by the reseller or the end user. Adjusting the ribbon tension this procedure c...

  • Page 319

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-17 adjusting the ribbon drive the ribbon drive sets the baseline for the ribbon tension and should not be adjusted by the reseller or end user. Adjusting the transfer temperature step pro...

  • Page 320

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-18 adjusting the transfer speed the transfer speed sets the baseline for the rate of image transfer and should not be adjusted by the reseller or end user. If a different transfer speed i...

  • Page 321

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-19 adjusting the image darkness step procedure 1 choose menu, print test image and alignment test to print a test card. 2 examine the test card. 3 select menu, setup printer, print settin...

  • Page 322

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-20 changing the encoder settings make this selection to modify the encoder settings. These settings would need to be changed (a) if the print board is replaced or (b) if the printer is up...

  • Page 323

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-21 setting the magnetic tof use this setting to position the magnetic data at the correct distance from the leading edge of the card. The magnetic tof is the distance from the edge of the...

  • Page 324

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-22 setting the magnetic tof (continued) use this setting to position the magnetic data at the correct distance from the leading edge of the card. The magnetic tof is the distance from the...

  • Page 325

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-23 setting the magnetic tof step procedure 7 press save to save the value. 8 test the position of the start sentinel by magnetically encoding a card and checking as described in step 1 in...

  • Page 326

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-24 adjusting the flipper offset step procedure 1 select menu, setup printer and flipper offset. 2 change the setting in small increments if the card is not feeding correctly. (note: a neg...

  • Page 327

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-25 adjusting the lamination flipper offset step procedure 1 select menu, setup printer and flipper offset or inverted offset. 2 change the setting in small increments if the card is not f...

  • Page 328

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-26 adjusting the lam tof and eof step procedure 1 applies only if the printer is equipped with the card lamination module. Use this control to align the polyguard overlaminate patch on th...

  • Page 329

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-27 adjusting the lamination sensor calibration step procedure 1 applies only if the printer is equipped with the card lamination module. (note: this setting reports the current lamination...

  • Page 330

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-28 using the show card count option step procedure 1 use this option to view the total card count (cc), pass count (pc), transfer count (tc). The card count is the total number of cards t...

  • Page 331

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 11-29 system upgrade (firmware upgrade) this option is used to upgrade the printer firmware. Step procedure 1 upgrade by selecting system upgrade. The lcd will prompt: are you sure you want ...

  • Page 332

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 12-1 section 12: firmware updates important: the procedures in this section apply for the hdp600/hdp600-lc and hdp600 cr100/hdp600-lc cr100 card printers. The purpose of this section is to p...

  • Page 333

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 12-2 firmware updater application program (continued) the firmware updater application program is the software required to send firmware updates from the computer to the printer. To download...

  • Page 334

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 12-3 downloading firmware updates step procedure 1 refer to the following steps to download firmware updates: 2 select the download firmware button. If you have internet access, this will au...

  • Page 335

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 12-4 updating the printer's firmware now that you have installed and opened the firmware updater program and downloaded the firmware update file, you can begin updating your printer's firmwa...

  • Page 336

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 12-5 updating the main firmware (continued).

  • Page 337

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 12-6 updating the main firmware (continued) step procedure 8 wait: the firmware update will now take a few minutes. Check the printer's lcd for the status. (note: when the update is complete...

  • Page 338

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 12-7 updating the lcd firmware step procedure 1 make sure the printer is powered on, connected to the pc and in its ready mode. 2 from the firmware updater program, click on the select updat...

  • Page 339

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 12-8 updating the lcd firmware (continued).

  • Page 340

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 13-1 section 13: fargo technical support important: the procedures in this section apply for the hdp600/hdp600-lc and hdp600 cr100/hdp600-lc cr100 card printers. The purpose of this section ...

  • Page 341

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 13-2 reading the serial numbers on a fargo printer the purpose of this section is to provide updated instructions for reading serial numbers on a fargo printer. Finding out when a fargo card...

  • Page 342: Lists

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 14-1 section 14: reviewing spare parts lists reviewing spare parts list for hdp600, hdp600-lc, hdp600 cr100 and hdp600-lc cr100 hdp600 series recommended spare parts list effective date: to ...

  • Page 343

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-1 section 15: glossary of terms term definition 24-bit color a color depth for an image that uses 8 bits for each color (red, blue, green) combining the possible 256 shades to provide a c...

  • Page 344

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-2 glossary of terms (continued) term definition barcodes a series of alternating black and white stripes, of varying widths (each character denoted by a set number and width of black stri...

  • Page 345

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-3 glossary of terms (continued) term definition cache a type of memory buffer to store data temporarily, used to hold information that is most often exchanged between controller and perip...

  • Page 346

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-4 glossary of terms (continued) term definition cr-79 a card dimension standard of 2.0625 l x 3.3125 w (+/-0.002 w, +/-0.005 l) or 52.400 x 84.150 mm. Cr-80 a card dimension standard of 2...

  • Page 347

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-5 glossary of terms (continued) term definition direct-to-card (dtc) printing the direct-to-card printing process prints digital images directly onto any plastic card with a smooth, clean...

  • Page 348

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-6 glossary of terms (continued) term definition dwell time the speed at which the card moves across the lamination roller, measured in seconds/inch (sec/in). This can be adjusted in the d...

  • Page 349

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-7 glossary of terms (continued) term definition encoder (wheel) an electromechanical device, attached to a shaft that detects the change in rotational position, incremented to count ticks...

  • Page 350

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-8 glossary of terms (continued) term definition flash memory a microchip based non-volatile memory device that holds its data when power is removed. This allows for field reprogramming of...

  • Page 351

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-9 glossary of terms (continued) term definition hard drive a high capacity storage device in a pc consisting of non- removable magnetically encodable platters. Hardware physical component...

  • Page 352

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-10 glossary of terms (continued) term definition ieee 1284 (institute of electrical and electronics engineers 1284) a standard method of signaling for a bi-directional parallel interface ...

  • Page 353

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-11 glossary of terms (continued) term definition landscape a document layout that is viewed with the document's long axis in a horizontal orientation. Lcd (liquid crystal display) a devic...

  • Page 354

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-12 glossary of terms (continued) term definition mb (megabyte) a unit of storage that equals 1,048,576 bytes. Memory a generic term for any device that stores digital information using ma...

  • Page 355

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-13 glossary of terms (continued) term definition oversized cards oversized cards are used for more efficient visual identification and are available in many non-standard sizes. The most p...

  • Page 356

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-14 glossary of terms (continued) term definition pinch roller a free spinning (non-driven) roller that presses the card against the drive roller, on the opposite side, to ensure an adequa...

  • Page 357

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-15 glossary of terms (continued) term definition printhead the device on a printer that produces the image on the media. Pvc abbreviation for polyvinyl chloride, often called vinyl. Pvc i...

  • Page 358

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-16 glossary of terms (continued) term definition resolution the number of individual pixels in a graphic, taken over a given length, used to indicate the sharpness of the picture and the ...

  • Page 359

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-17 glossary of terms (continued) term definition saturation a measure of the degree of color, from gray, with the same brightness. Self-test a pre-determined print file used to confirm pr...

  • Page 360

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-18 glossary of terms (continued) term definition spooling rather than moving a print job directly to the printer, the job is written to the disk so that the user can access the applicatio...

  • Page 361

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-19 glossary of terms (continued) term definition thermocouple a device for measuring temperature using a junction of two wires of dissimilar metals that produce a voltage when heated that...

  • Page 362

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 15-20 glossary of terms (continued) term definition ups (un-interruptible power supply) an ac power supply, typically powered by batteries, which provides temporary power to the pc or printe...

  • Page 363: Section 16: Index

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 16-1 section 16: index a about button, 7-23 absolute failure, 7-9 ac - alternating current, 15-1 accelerated wear/dye migration, 7-7 accepted card compositions, 2-8 accepted card thickness, ...

  • Page 364

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 16-2 cr-80, cr-90 and cr-100, 7-13, 7-16 cr-90, 15-4 cr-90 or cr-100, 2-29 csa, 2-6 cursor, 15-4 custom 1/custom 2 options, 7-6, 7-18, 7-19 custom image transfer settings., 7-6 customization...

  • Page 365

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 16-3 glossy / matte, 15-8 glossy pvc, 15-8 glossy-pvc or matte-pvc options, 7-45 graphical device interface (gdi), 15-8 gray scale, 15-8 gray/align ymc, 11-19 gray/align ymck, 4-17 guide eje...

  • Page 366

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 16-4 m mag encoding, 15-11 mag stripe, 15-11 mag track, 15-11 mag verify, 15-11 magnetic card analyzer, 11-21 magnetic encoding tab, 7-54 magnetic stripe encoding modules, 7-55 magnetic stri...

  • Page 367

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 16-5 print test image, setup printer, show error count, show card count and system upgrade, 11-1 print the first page of a two-page document, 7-33 print timeout error, 4-9 print width, 2-7, ...

  • Page 368

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 16-6 start sentinel, 11-23 start sentinel (ss), 7-65, 11-21, 11-22 start sentinel distance, 11-21 stepper motor, 15-18 string, 15-18 supply frequency, 2-13 supply voltage, 2-13 surface mount...

  • Page 369: Section 17: Appendix A

    Restricted use only fargo electronics, inc. Hdp600 high definition card printer/encoder user guide (rev. 2.3) 17-1 section 17: appendix a attached please find the two (2) hdp600 menu option structure trees..

  • Page 370

    Hdp600 high definition card printer/encoder – cr-100 and cr-80 menu tree transfer tension transfer temp transfer eof transfer tof transfer drive transfer settings sensor automatic lam flip offset lam invert offset lam eof lam tof lam temp sensor manual current value x -500min +0max current value x -...

  • Page 371

    Hdp600 high definition card printer/encoder – cr-100 and cr-80 menu tree transfer tension transfer temp transfer eof transfer tof transfer drive transfer settings sensor automatic lam flip offset lam invert offset lam eof lam tof lam temp sensor manual current value x -500min +0max current value x -...