1. DL manuals
  2. FARM STAR
  3. Spreader
  4. CS-1094
  5. Owner's Manual

FARM STAR CS-1094 Owner's Manual

Manual is about: Broadcast Seeder/Spreader PTO DRIVEN – 3-PT. MOUNTED

Summary of CS-1094

  • Page 1

    Attention! Safety rules 1. Read instruction manual and make sure all operators are knowledgeable on correct operation of equipment and familiar with the safety rules of operation. 2. Never allow riders on equipment. 3. When operating on rough or uneven terrain, use extreme caution and a safe operati...

  • Page 2: To The Owner/operator/dealer

    To the owner/operator/dealer all implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe -minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its saf...

  • Page 3: Obey All

    Measure the distance between the ends of the two shafts (dimension “a”, figure 1). Each half of the pto should be equal to dimension “a” minus two (2) inches. If the driveline must be cut to a shorter length, clamp driveline in a well-padded vise to prevent damage to the shield (figure 3). Cut the p...

  • Page 4: Caution!

    Operating instructions 1. Right -hand or left-hand reference is determined by standing at the rear of the seeder/spreader and facing in the direction of travel of the tractor. 2. Check the register of the control lever indicator with the seed gate (material gate). With the seed gate closed, the cont...

  • Page 5

    Maintenance 1. The hopper should be washed after use, especially after use with corrosive material such as fertilizer, salt, or ice melting compounds. When dry, oil thoroughly. 2. The gearbox is filled with lubricant and sealed at the factory. If operated and stored properly, the gearbox will provid...

  • Page 6

    Spreading chart for fertilizers note: spread widths of fertilizer will vary according to type. Always check actual spread width and application rate. Note: spread chart settings are approximate – always make trial run to check actual application rate. Warning 1. Be sure spinner is stopped during hit...

  • Page 7: Spreading Chart For Seed

    Spreading chart for seed note: spread chart settings are approximate – always make a trial run to check actual application rate. Note: material can vary as to density, foreign material content, particle size and shape. These factors will affect both spread width and flow rate. Page 7 s p r e a d t r...

  • Page 8

    Exploded parts drawing for cs series spreaders page 8.

  • Page 9

    Repair parts for cs series seeder/spreaders page 9 ref. No part no. Description no. Req'd 1 420701 frame, xa 1 2 420702 bolt, hex head, m8 x 20, zinc 2 3 420703 washer, flat, 8mm, zinc 4 4 420704 washer, flat, 10mm, zinc 7 5 420705 nut, self-locking, m10, zinc 1 6 420706 washer, bakelite 1 7 420707 ...

  • Page 10: Pto Components

    Page 10 ref. No part no. Description no. Req'd 46 420748 pto assembly, complete 1 63 420764 pto half, tractor end 1 64 420765 plastic shield assembly, outer 1 65 420766 pto half, implement end 1 66 420767 plastic shield assembly, inner 1 67 170804 yoke, 1-3/8-6b spline 2 68 3814091 pto cross repair ...

  • Page 11: Gearbox Components

    Page 11 gearbox components optional agitator components ref. No. Part no. Description no. Req. 45 420747 gearbox, 3-hole (complete) 1 47 420749 gearbox half, right hand 1 48 420750 shaft, output assembly 1 49 420751 oil seal, 25 x 37 x 5 1 50 420752 bearing, 6205 2 51 420753 gearbox half, left hand ...

  • Page 12: Safety Precautions

    Safety precautions most accidents occur because of neglect or carelessness. Avoid needless accidents by following all of the safety precautions listed below. 1. Machinery should be operated only by those who are responsible and are authorized to do so. 2. Stop the engine, lower all equipment, lock t...