- DL manuals
- FastTan
- Lantern
- SunBoard XTT
- Care, Use And Installation Instructions
FastTan SunBoard XTT Care, Use And Installation Instructions
Summary of SunBoard XTT
Page 1
1 indoor tanning equipment care, use and installation instructions model: sunboard xtt pc marketing 1040 wilt avenue ridgefield, nj 07657 1-800-fast tan.
Page 2
2 preface your unit has been built in accordance with the latest state of technology and is safe. However, the unit can be dangerous if it is operated by persons who have not recei- ved the necessary training or instruction, or if it is used improperly. Therefore, everyone entrusted with the task of...
Page 3
3 1 safety instructions: 1.1 before installation and placing in operation, the safety instructions and operating instruc- tions must be carefully read and observed. 1.2 before the unit is placed in operation, the local safety regulations and the safety instructions must be complied with. 1.3 safety ...
Page 4
4 note the tan produced by this unit is a deep. Rich ”cosmedic” tan, however, regardless of how much an individual may tan with this unit, it will not provide adequate protec- tion against overexposure to natural sunlight or uvb tanning systems. Skin type ii - this is the individual that usually bur...
Page 5
5 warning warning 1 48 88 90 89 91 operation i information for the user of the unit 2.1 start of sunbathing observe the time chart. Do not exceed the sunbathing time recommended for your skin type. You must definitely avoid sunburn. Never sunbathe if you already have sunburn. Depending on the type o...
Page 6
6 warning warning function function 2.4 cleaning the acrylic sheet: use uwe cleanser only! Always ensure extremely strict hygiene. After every period of use, the lying surface must be disinfected and cleaned. Uwe cleanser and other cleaning materials must not be sprayed into the eyes. Do not spray t...
Page 7
7 2 53 32 33 37 42 27 50 31 15 16 11 10 7 8 17 5 6 13 78 14 9 23 42 47 63 62 95 39 30 29 20 28 22 21 54 53 51 50 19 36 38 24 52 49 25 26 18 106 105 x5a-x9a 12 connection speaker x5a x6a x7a x8a x9a see picture 8 • assembly of the tripod (27, picture 2) remove the tripod (27) out of the cardboard and...
Page 8
8 3 function 44 40 92 41 43 66 81 80 78 9 3 10 4 83 86 85 66 107 108 107 84 104 84 94 46 45 48 64 34 • assembly of the upper tanning arm (41, picture 3) take the upper tanning arm (5 sunbathing units) and hold it in front of the respective place of installation at the tripod. First pull the cable x5...
Page 9
9 warning function function function • assembly of the tanning arm right/left (84, picture 3) attention! Take care that you assemble the tanning arm with the operation panel (48) on the correct side (left). At first take the tanning arm with operation panel and hold it in front of the corresponding ...
Page 10
10 4 warning warning • assembly of the lounger (picture 4). Place the pipeframe (2) over the footrack. Take care, that the front foot is being fixed by the support (73). Attention! The feet of the pipeframe are adjustable for height. The knurling screws (103) have been unscrewed up to 25mm ex works....
Page 11
11 warning warning warning warning 3.3 connecting the unit’s air outlet attention! Important information! On using the sunboard xtt unit you really must draw oft the already warmed up cooling air through a direct air removal. Uwe recommends as standard connexion a special adapter part (59), which yo...
Page 12
12 5 dimensions in mm 5 4 3 2 1 4 3 2 1 350 2330 1950 645 1920 890 600 475 1010 1635 370 290 660 1950 780 1010 1635 800 290 370 1950 4 setting into operation 4.1 technical data and dimensions designation sunboard xtt type of unit 7823 power (w) 13.500 operating voltage (v) 3pe ~ 60 hz 220 v 50 a fus...
Page 13
13 function warning cover of the lights the sources of uv-radiation in the arms are covered each by one 3-4,5 mm thick filter with the denomination type 322 xtt (pkz 02935) and by one disk out of 3 mm thick acrylic glass. The sources of uv-radiation in the lounger are covered each by one 3-4,5 mm th...
Page 14
14 6 warning warning function 6 maintenance and repair always disconnect the unit from the mains! The company operating the unit must ensure that the unit is always operated in perfect condition only. Ensure regular maintenance and checking of the technical equipment. In the case of repair work or a...
Page 15
15 function warning warning function 6.2 exchanging the high pressure burner the high pressure burner shall only be used with the xtt- filter disk. The unit must not be operated if the disks are damaged or missing. Danger of burning! Danger of lightning damage to the eyes! The xtt-filter disk is pro...
Page 16
16 7 warning exchanging of the high pressure burner in the lounger (picture 7) take down the acrylic sheet (1) according to the above detailed description. Unscrew the two oval-head and self- tapping screws (74) out of the disk support (75). Disassemble the disk support by lifting the disk support o...
Page 17
17 warning warning warning! Install the xtt filter disk (72) nearest the user. Install the xtt filter disk in the disk holder as shown in fig. 7. Introduce the clean xtt filter disk again into the disk support (75). Screw in tight again the covering plate (98). Hold the disk support in such a way, t...
Page 18
18 8 tips for correcting minor defects before you begin maintenance and repair work, you must disconnect the unit from the mains. Repairs should only be performed by the uwe company or by authorised persons. Safety devices must not be removed or disabled. After each repair, there must be made an exa...
Page 19
19 9 waste • high pressure burner the high pressure burner and the illumination light are special ref uses. They should not be thrown together with the regular waste. The local offices will inform you, where the burner could be properly wasted. • unit faulty units should be disposed of according to ...
Page 20
20 id-nr. 265 360 / 03/03 pc marketing 1040 wilt avenue ridgefield, nj 07657 1-800-fast tan.