Easy assembly instructions & rules tm model # 64-0500 do not return to store. For all returns and warranty coverage please call gld products: 1-800-225-7593 please provide model number, serial number, and/or part number of the product or part when you call. Numbers can be found on outside of packagi...
This manual is provided to instruct you during the assembly of your new fat cat™ shot king pool table. Please refer to it as necessary. Be sure to have another person help you assemble the table. Careful handling of all parts during assembly will ensure many years of enjoyment! Fat cat™ pool tables ...
Step 1: assembling the pedestals for each pedestal, locate the predrilled holes on interior surface of each leg post. Line up predrilled holes in (#26) support blocks and attach to leg posts with 2 (#2) philips head screws. Repeat for all. Next, slide 1 (#21) leg panel into the precut slot into 1 (#...
Step 3: attaching the slate support beams set (#32) end cross beams on top of side beams, lining up predrilled holes. Attach loosely with 8 (#8) hex bolts, 8 (#6) black washers, 8 (#10) washers, 8 (#11) spring washers, and 8 (#9) hex nuts. Repeat process for (#30) center cross beams. Tighten down al...
Step 4: securing the slate with the help of another person, place the middle section of (#33) slate on the center supports of the base. Measure from the edge of slate to outer edge of end cross beams. Make sure this piece is centered perfectly, is square to all sides, and that the overhang is equal ...
Step 5: leveling the slate using the carpenter’s level determine which of the 3 sections is least level. Begin the leveling process with this section by adjusting the levelers with the (#47) allen wrench. When it is level, set the other 2 sections to match it. Make sure the seams are smooth and all ...
Move to the center of the opposite end of the table. With one hand, pull the cloth tightly toward you until you have a 1-1/2" fold in the center of the cloth and with the other hand press it firmly into place. Pull the sides of the cloth tightly toward their respective corners. Smooth and press firm...
Press the cloth firmly against the slate along the curve of all pockets. Trim off excess cloth with scissors or box cutter. Locate the 18 holes for the rail bolts along the perimeter of the tabletop. Carefully punch holes in the cloth. Using a philips screwdriver, run the shaft of the screwdriver ar...
9 step 8: assembling rails and pockets set all rail pieces into position on table top. Loosely attach (#38) side rail section to base on the underside of table with (#18) hex bolts and (#19) washers. Loosely attach (#39) end rails in same manner. Slide (#40) corner pieces on loosely. Adjust rail fit...
#27. Leg protector 4 pieces 10 #24. Pocket nails 24 pieces #25. Leg center brace 2 pieces #26. Support block 4 pieces #22. Leg post a 2 pieces #23. Leg post b 2 pieces #15. 1/4" x 1/2" allen bolt 4 pieces #16. 1/4" x 32mm washer 4 pieces #18. 5/16" x 1-3/4" hex bolt 18 pieces #19. 5/16" x 35mm washe...
#47. Allen wrench 1 large, 3 small #39. End rail 2 pieces #40. End rail corner 4 pieces #41. Drop pocket 12 pieces #42. Felt brush 1 piece #43. Chalk 2 pieces #44. Billiard balls 1 set #45. Triangle 1 piece #46. 2 cue sticks 4 pieces #37. Apron corner 4 pieces #38. Side rail 2 pieces #50. Joint comp...
Gld products s84 w19093 enterprise drive muskego, wi 53150 usa 800 225 7593 • fax 800 841 6944 email: gld@gldmfg.Com do not return to store for all returns and warranty coverage, please call: gld products 1-800-225-7593 please provide model number, serial number and/or part number when you call. Num...
