- DL manuals
- FB Jets
- Toy
- T33
- Assembly Manual
FB Jets T33 Assembly Manual
Summary of T33
Page 1
Fei bao/fb jets large t33 fb jets/ feibao t33 construction manual written by tyson dodd in collaboration with fei bao jets.
Page 2
Fei bao/fb jets large t33 disclaimer this is not a toy. This is a high-performance miniature aircraft, capable of high speeds and damage to life, limb, and property. The manufacturer and its distributors cannot control how you assemble this model, what equipment you use to fit it out, or how you fly...
Page 3
Fei bao/fb jets large t33 table of contents disclaimer........................................................................................................................................................ 2 introduction .................................................................................
Page 4
Fei bao/fb jets large t33 introduction you have chosen a model that represents the pinnacle of arf technology and factory testing with the new manufacturing processes implemented by fb jets. While there is not a lot of building to do in comparison to traditional modelling techniques, there is enough...
Page 5
Fei bao/fb jets large t33 construction preliminary steps the following setup is recommended by fb jets for all kits that they manufacture and request the modeller to conduct these quick and simple steps to not only make your build easier, but cleaner. • clean and inspect all parts. Inventory them ag...
Page 6
Fei bao/fb jets large t33 step 1: check forward fuselage • remove the fuel tanks from the fuselage. • also remove the forward component boards. Now would be a good time to put a coat of paint on these parts if you would like to protect the wood surfaces. • vacuum and thoroughly clean the fuselage co...
Page 7
Fei bao/fb jets large t33 external clean the area down with e sanding dremel. Place a thin layer of epoxy over the leak area and then lay some thin fibreglass cloth over the leak area. Using your fuel pump, draw the air out of the tank so that the glass and epoxy are drawn into the leak from the out...
Page 8
Fei bao/fb jets large t33 step 5: nose doors it will be helpful at this point to ensure that you are happy with the function of the nose door. The manufacturing process on this model is very high and we did not have to change or tighten anything at all with the nose wheel gear doors. • refer to the ...
Page 9
Fei bao/fb jets large t33 photo 2 – air lines colour coded and run to the centre area of the component boards. The speed brake air lines have been run to this spot too. Step 6: vertical fin and rudder • before attaching the aft section of the fuse, the vertical fin and horizontal stabilizers need to...
Page 10
Fei bao/fb jets large t33 photo 3 – rudder servo and push rod. • run the servo wire out of the bottom of the vertical stab. • trial fit the phenolic control arm in the slot routed in the rudder at the factory. You may need to use a small carbide cutter to enlarge the slot slightly for a good fit. Be...
Page 11
Fei bao/fb jets large t33 step 7: horizontal stabilizers • the horizontal stabs build up in a similar fashion to the vertical stab in terms of the servo installation. Install your servos in the space provided and modify slightly as required if your selected servo does not fit. Repeat all steps, incl...
Page 12
Fei bao/fb jets large t33 photo 5 – mounting thrust tube, bypass and engine. • adjust the location of your engine to obtain the clearance specified by the manufacturer between the exhaust cone and the pipe mouth. It is likely it will extend into the intake. • shim the engine as necessary to make sur...
Page 13
Fei bao/fb jets large t33 • wire tie the brake line to the main strut and check operation of the gear once more to make sure brake line has adequate length and clearance. Photo 6: main gear step 13: aileron and flap servos • remove the aileron servo covers. Mark the inside front of the covers so you...
Page 14
Fei bao/fb jets large t33 • rough up the mounting surface of the control horn, tape around the slot and glue the horn into each control surface with aeropoxy or hysol. • set the wings aside for the glue to cure. Double check to make sure there are no fingerprints or excess glue on the wing surfaces....
Page 15
Fei bao/fb jets large t33 step 15: cockpit • trim the edges of the cockpit area so that the tubs sit inside the canopy. We fitted the scale cockpit supplied into the canopy to make start-up easier and preparation easier. • we suggest trial fitting the cockpit to the fuselage and trimming where neces...
Page 16
Fei bao/fb jets large t33 equipment installation photos • equipment, including fuelling tubes, switches, air fill, air gauges and remote ecu board were all installed in on the component boards to have as much weight forward as possible. Also, the wiring for the ecu and for the servos was run down op...
Page 17
Fei bao/fb jets large t33.
Page 18
Fei bao/fb jets large t33.
Page 19
Fei bao/fb jets large t33.