Fdi usb-icp-sab9 quick start guide fdi page 1 of 15 rev 1.0 usb-icp-sab9 quick start guide the usb-icp-sab9 is a socket adapter board designed to be used with the usb in-circuit programmer for nxp semiconductors lpc9xx devices. The sab9 allows the user to program and test these microcontrollers outs...
Fdi usb-icp-sab9 quick start guide fdi page 2 of 15 rev 1.0 usb-icp-sab9 socket layout: each socket on the board is clearly labeled for the type of part that is programmed in it. When this document refers to the ‘top’ of the board, this is referring to the top of the board when it is in the orientat...
Fdi usb-icp-sab9 quick start guide fdi page 3 of 15 rev 1.0 connecting the usb-icp-sab9 to a usb-icp to use the sab9, it must first be connected to a pc through a usb-icp with a usb-icp-lpc9xx cable to p1, as shown above. Or, if you do not have the usb-icp-lpc9xx, the sab9 may be connected to the pc...
Fdi usb-icp-sab9 quick start guide fdi page 4 of 15 rev 1.0 frequently asked questions for frequently asked questions regarding the usb-icp please visit: www.Teamfdi.Com/usb-icp error messages when using flash magic flash magic is the pc gui interface software used with the usb-icp programmer. If yo...
Fdi usb-icp-sab9 quick start guide fdi page 5 of 15 rev 1.0 p89lpc90x devices in dip8 package: skt1 when placing any dip8 part in the sab9 for programming, there must be 5 pins empty above and below the part being programmed. The pin one identifier (notch in chip) should be toward the top of the boa...
Fdi usb-icp-sab9 quick start guide fdi page 6 of 15 rev 1.0 p89lpc2x devices in dip20 package: skt1 when placing any dip20 part in the sab9 for programming, there must be 2 pins empty above and below the part being programmed. The pin one identifier (notch in chip) should be toward the top of the bo...
Fdi usb-icp-sab9 quick start guide fdi page 7 of 15 rev 1.0 using the tssop socket (skt2) to place a part in the tssop socket for programming, first push down on both sides of the socket with two fingers. Then, once the socket is ‘open’ drop the part into the socket and nudge it into place to match ...
Fdi usb-icp-sab9 quick start guide fdi page 8 of 15 rev 1.0 p89lpc91x devices in tssop14 package: skt2 when placing any tssop14 part in the sab9 for programming, there must be 3 empty pins above and 4 empty pins below the part being programmed. The pin one identifier (circle in top left corner) shou...
Fdi usb-icp-sab9 quick start guide fdi page 9 of 15 rev 1.0 p89lpc91x devices in tssop16 package: skt2 when placing any tssop16 part in the sab9 for programming, there must be 3 empty pins above and below the part being programmed. The pin one identifier (circle in top left corner) should be toward ...
Fdi usb-icp-sab9 quick start guide fdi page 10 of 15 rev 1.0 p89lpc92x devices in tssop20 package: skt2 when placing any tssop20 part in the sab9 for programming, there must be 2 pins empty above and below the part being programmed. The pin one identifier (circle in top left corner) should be toward...
Fdi usb-icp-sab9 quick start guide fdi page 11 of 15 rev 1.0 p89lpc93x devices in tssop28 package: skt2 when placing any tssop28 part in the sab9 for programming, the part should take up the entire socket and there should be no empty pins. The pin one identifier (circle in top left corner) should be...
Fdi usb-icp-sab9 quick start guide fdi page 12 of 15 rev 1.0 p89lpc910x devices in hvson10 package: skt4 when placing any hvson10 part in the sab9 for programming, the part should be turned so that the pin 1 identifier is in the upper left corner of the socket..
Fdi usb-icp-sab9 quick start guide fdi page 13 of 15 rev 1.0 p89lpc93x devices in hvqfn28 package: skt3 when placing any hvqfn28 part in the sab9 for programming, the part should be turned so that the pin 1 identifier is in the upper left corner of the socket..
Fdi usb-icp-sab9 quick start guide fdi page 14 of 15 rev 1.0 led and jumper function led1: this led is the power indicator and should be illuminated when the sab9 board is plugged into an active usb-icp. Led2: this led can be used as the standard ‘heartbeat’ monitor. By adding code to blink this led...
Fdi usb-icp-sab9 quick start guide fdi page 15 of 15 rev 1.0
