User manual fec-150 thermal printer rev. 1.00 http://www.Firich.Com.Tw.
Rev. 1.00 - 2 - fec-150 ■ safety warning proper use of this product can prevent hazardous or physical harm. Make sure all following instructions are followed when using this product. Warning violation of following instructions may cause serious injure or risk of life. Keep it in plastic bag and keep...
Rev. 1.00 - 3 - fec-150 caution violation of following instructions may cause slight injure or damage to the product. Do not use a malfunctioned product that may cause a fire or electric shock. • power off the printer, remove the plug from the socket and co ntact the distributor. Note that no water ...
Rev. 1.00 - 4 - fec-150 copyright firich (c) copyright cirich co., ltd. All rights reserved partial or total duplication, reproduction or translation of the user manual and product or convert to any electronic media or readable form without prior written permission is prohibited. The errors related ...
Rev. 1.00 - 5 - fec-150 ■ introduction assembly name (1) cover paper (2) roller ass’y (3) paper (4) cover cutter (5) cover fucntion (6) case main (7) case lower (8) communication port - p arallel/serial (9) cash drawer (rj-11) (10) usb communication rear fec-150p/r,fec-150u the printer is a banking ...
Rev. 1.00 - 6 - fec-150 ■ table of contents 1. Installation and basic operations ·················································································7 1-1 unpacking ·····················································································································7 1-2...
Rev. 1.00 - 7 - fec-150 1. Installation and basic operations 1-1 unpacking make sure all following items are available. Please contact the distributor immediately in case of loss or damage. 1-2 installation site keep the product away from the high temperature or direct sunlight. Do not place it at t...
Rev. 1.00 - 8 - fec-150 1-3 operation panel the panel consists of one button and two indicators. Button feed to print one paper, press the feed button. To continuously print, press and hold the feed button. Indicator the indicator indicates the state of the printer. Power (green) the indicator light...
Rev. 1.00 - 9 - fec-150 2. Connection 2-1 ac adapter connection it is required to used the power cord and adapter accompanied with the printer. ※ warning improper power unit may cause a fire or hazard. ※ note 1. Operate the product in the following orders for safety and durability after power on. 1)...
Rev. 1.00 - 10 - fec-150 2-2 interface connection usb, serial or parallel interface cable is required for connecting the printer to the computer. - make sure the power of the printer and computer is switched on, then connect the cable interface to the printer. - in the case of serial and parallel ca...
Rev. 1.00 - 11 - fec-150 2-2-1 fec-150r serial interface printer case main 1 - 1 - 2 txd --------------------- 2 rxd 3 rxd --------------------- 3 txd 4 dsr --------------------- 4 dtr 5 gnd --------------------- 5 gnd 6 dtr --------------------- 6 dsf 7 cts --------------------- 7 rts 8 rts -------...
Rev. 1.00 - 12 - fec-150 2-2-2 fec-150p parallel interface printer case main 1 nstrobe ---------------- 1 nstrobe 2 data 0 (lsb) ---------------- 2 data 0 (lsb) 3 data 1 ---------------- 3 data 1 4 data 2 ---------------- 4 data 2 5 data 3 ---------------- 5 data 3 6 data 4 ---------------- 6 data 4...
Rev. 1.00 - 13 - fec-150 2-2-4 cash drawer cable connection (option) pin no. Description direction 1 frame gnd - 2 drawer kick-out driver signal #1 output 3 drawer open / close signal input 4 +12v - 5 drawer kick-out driver signal #2 output 6 signal gnd -.
Rev. 1.00 - 14 - fec-150 3. Dip switch setting ※ note it is required to turn off the printer when setting the dip switch to prevent electrical rejection and damage to the printer. Replacement of the contact device or the printing density can be set on the dip switch. 1. Make sure the printer powers ...
Rev. 1.00 - 15 - fec-150 refer to the following settings of the dip switch. 3-1 setting the dip switches 3-1-1 setting the dip switch (rs-232c serial interface) • dip switch sw function on off default 1-1 auto cutter disable enable off 1-2 reserved - 1-3 off 1-4 baud rate refer to table 1 off • tabl...
Rev. 1.00 - 16 - fec-150 msw2 switch function on off 1 reserved - fixed to off 2 auto cutter function full cutting partial cutting 3~8 code page selection refer to following table msw2-8 msw2-7 msw2-6 msw2-5 msw2-4 msw2-3 character table off off off off off off page 0 437 (usa,standard europe) off o...
Rev. 1.00 - 17 - fec-150 msw9 switch function on off 1 language selection korean/chinese eng 2~4 reserved - fixed to off 5~8 international character set selection refer to following table msw9-8 msw9-7 msw9-6 msw9-5 international character set off off off off 0. Usa off off off on 1. France off off ...
Rev. 1.00 - 18 - fec-150 4. Paper loading please use the standard paper. ※ note it is important to power off the printer in the process of paper loading. 1. Open the paper cover and take out all used paper. 2. Load the paper in the proper direction as the following shown in case of paper jam. 3. Pla...
Rev. 1.00 - 19 - fec-150 5. Sample test 1. Sample printing test * sample test start-up after loading paper and close the cover and the paper feed button pressed and held, the sample test will start upon power on. The self-test will conduct printing according to the existing setting of the following ...
Rev. 1.00 - 20 - fec-150 6. Hexadecimal dumping this function is designed for advanced user to send and receive the data accurately and identify the software problems. The hexadecimal dumping function is helpful for searching special terms because all data and command statements are printed in hexad...
Rev. 1.00 - 21 - fec-150 7. Specification printing method thermal printing resolution 203dpi (8 dot/mm) printing width 48mm paper width 58.0±0.5mm strings per line 32 (font a) (12x24) printing speed about 19 lines/sec max. 65 mm/sec at 25℃/printing duty 12.5% thickness: 0.062 ~ 0.075mm roller size: ...
Rev. 1.00 - 22 - fec-150 8. Windows driver setting 8-1 serial (rs-232c) interface model windows driver setting 1. After executing the proudct setting cd, go to thermal printer > fec-150 > drivers > windows driver > drivers folder > exectute fec-150_win_vx.X.Xx.Exe 2. Select “next” from the window at...
Rev. 1.00 - 23 - fec-150 8-2 parallel (ieee1284) interface windows driver setting 1. After executing the proudct setting cd, go to thermal printer > fec-150 > drivers > windows driver > drivers folder > exectute fec-150_win_vx.X.Xx.Exe 2. Select “next” from the window at the initial setting. 3. Inst...
Rev. 1.00 - 24 - fec-150 9. Control command list command name ht horizontal tab lf to print and line feed cr to print and carriage return dle eot to send the real time status esc sp to set the right side space of the characters esc ! To set the printing mode esc $ to set the absolute position esc % ...
Rev. 1.00 - 25 - fec-150 10. Summary of control command ht [name] horizontal tab [type] ascii ht hex 09 decimal 9 [description] set the horizontal tab if you want to use the print position. Lf [name] to print and line feed [type] ascii lf hex 0a decimal 10 [description] to print the data in the prin...
Rev. 1.00 - 26 - fec-150 n = 1: printer status bit off/on hex decimal function 0 off 00 0 not used. Fixed to off 1 on 02 2 not used. Fixed to on 2 off 00 0 not used off 00 0 on-line 3 on 08 8 off-line 4 on 10 16 not used. Fixed to on 5-6 - - - not defined 7 off 00 0 not used. Fixed to off n = 2: off...
Rev. 1.00 - 27 - fec-150 esc sp n [name] to set the right side space of the characters [type] ascii esc sp n hex 1b 20 n decimal 27 32 n [range] 0 ≤ n ≤ 255 [description] to set the right side space of the characters esc ! N [name] to set the printer mode [type] ascii esc ! N hex 1b 21 n decimal 27 ...
Rev. 1.00 - 28 - fec-150 esc % n [name] to select/cancel user defined character set [type] ascii esc % n hex 1b 25 n decimal 27 37 n [range] 0 ≤ n ≤ 255 [description] to select/cancel user-defined character set. User-defined character set is cancelled when lbs of n is 0, user-defined character set i...
Rev. 1.00 - 29 - fec-150 esc – n [name] to set/clear underline mode [type] ascii esc - n hex 1b 2d n decimal 27 45 n [range] 0 ≤ n ≤ 2, 48 ≤ n ≤ 50 [description] underline mode is set or cleared depending on the value of n. N function 0,48 underline mode is cleared 1,49 underline mode is selected (d...
Rev. 1.00 - 30 - fec-150 esc ? N [name] to cancel the user defined character set [type] ascii esc ? N hex 1b 3f n decimal 27 63 n [range] 32 ≤ n ≤126 [description] to cancel the user-defined character sets. Esc @ [name] to initialize the printer [type] ascii esc @ hex 1b 40 decimal 27 64 [descriptio...
Rev. 1.00 - 31 - fec-150 esc r n [name] to select multilanguage character sets [type] ascii esc r n hex 1b 52 n decimal 27 82 n [range] 0 ≤ n ≤ 10 [description] to select the multilanguage character set with n. Chinese version is not supported. N character set n character set 0 u.S.A. 6 italy 1 fran...
Rev. 1.00 - 32 - fec-150 esc v n [name] to set/clear 90° clockwise rotated character sets [type] ascii esc v n hex 1b 56 n decimal 27 86 n [range] 0 ≤ n ≤ 1, 48 ≤ n ≤ 49 [description] to set/clear 90° clockwise rotated character sets depending on the value of n. N function 0,48 to clear the 90° cloc...
Rev. 1.00 - 33 - fec-150 esc t n [name] to select the character code table [type] ascii esc t n hex 1b 74 n decimal 27 116 n [range] 0 ≤ n ≤ 5, n = 11, 255 [description] n is used to select the character code table as follows. Chinese version is not supported. N page 0 0: pc437 [u.S.A., standard eur...
Rev. 1.00 - 34 - fec-150 fs q n [xl xh yh d1 …dk]1…[xl xh yl yh d1…dk]n [name] to define nv image [type] ascii fs q n [xl xh yh d1 …dk]1…[xl xh yl yh d1…dk]n hex 1c 71 n [xl xh yh d1 …dk]1…[xl xh yl yh d1…dk]n decimal 28 113 n [xl xh yh d1 …dk]1…[xl xh yl yh d1…dk]n [range] 1 ≤ n ≤ 255, 0 ≤ nl ≤ 255...
Rev. 1.00 - 35 - fec-150 gs ( e pl ph fn [parameter] [name] to customize nv memory area [description] customize the nv user memory area. The table below explains the functions available in this command. Executes commands related to the user setting mode by specifying the function code fn. Fn format ...
Rev. 1.00 - 36 - fec-150 printer clears the receive and print buffers, and resets all settings (user- defined character, downloaded bit images, macros, and the print mode) to the mode that was in effect at power on. ▪ this function code (fn=2) is enabled only in the user setting mode. Gs ( e pl ph f...
Rev. 1.00 - 37 - fec-150 gs ( e pl ph fn a (fn=4) [format] [range] [description] ascii gs ( e pl ph fn a hex 1d 28 45 pl ph fn a decimal 29 40 69 pl ph fn a (pl + ph x 256) = 2 (pl=2, ph=0) fn=4 a=1, 2, 8, 9, 10, 11 ▪ transmits the setting value(s) of the memory switch specified by a. Hex decimal am...
Rev. 1.00 - 38 - fec-150 gs : [name] to define beginning/end of macro [type] ascii gs : hex 1d 3a decimal 29 58 [description] to define beginning/end of macro gs b n [name] black and white switching printer mode on/off [type] ascii gs b n hex 1d 42 n decimal 29 66 n [range] 0 ≤n ≤255 [description] b...
Rev. 1.00 - 39 - fec-150 gs l nl nh [name] to set the left margin [type] ascii gs l nl nh hex 1d 4c nl nh decimal 29 76 nl nh [range] 0 ≤ nl ≤ 255 0 ≤ nh ≤ 255 [description] left margin is determined by nl and nh. Left margin is set to [(nl + nh x 256) x (horizontal motion unit6)] inches printable a...
Rev. 1.00 - 40 - fec-150 gs ^ r t m [name] to run the macro [type] ascii gs ^ r t m hex 1d 5e r t m decimal 29 94 r t m [range] 0 ≤ r ≤ 255 , 0 ≤ t ≤ 255 , 0 ≤ m ≤ 1 [description] to run the macro - r: repetition frequency of macro execution. - t: delay time for executing all macros is t x 100 msec....
Rev. 1.00 - 41 - fec-150 ① gs k m d1...Dk nul ② gs k m n d1...Dn [name] to printer barcode [type] ① ascii gs k m d1...Dk nul hex 1d 6b m d1...Dk 00 decimal 29 107 m d1...Dk 0 ② ascii gs k m n d1...Dn hex 1d 6b m n d1...Dn decimal 29 107 m n d1...Dn [range] ① 0 ≤ m ≤ 6 (values for k and d are determi...
Rev. 1.00 - 42 - fec-150 control character control character ascii hex decimal hri character ascii hex decimal hri character nul 00 0 ■u dle 10 16 ■p soh 01 1 ■a dc1 11 17 ■q stx 02 2 ■b dc2 12 18 ■r etx 03 3 ■c dc3 13 19 ■s eot 04 4 ■d dc4 14 20 ■t enq 05 5 ■e nak 15 21 ■u ack 06 6 ■f syn 16 22 ■v ...
Rev. 1.00 - 43 - fec-150 the following characters can be represented by the code128 barcode. * shift characters in the code set a, the character right next to the shift follows the process of code set b. Shift character cannot be used in code set c. * code set selection character (code a, code b, co...
Rev. 1.00 - 44 - fec-150 gs v 0 m xl xh yl yh dl…dk [name] to print raster bit image [type] ascii gs v 0 m xl xh yl yh dl…dk hex 1d 76 30 m xl xh yl yh dl…dk decimal 29 118 48 m xl xh yl yh dl…dk [range] 0 ≤ m ≤ 3 , 48 ≤ m ( 51 0 ≤ xl ≤ 255 , 0 ≤ xh ≤ 255 , 0 ≤ yl ≤ 255 0 ( d ( 255 k = (xl+xhx256) x...