FeiYu Tech FY WGS Manual
3
2
Manual Version 1.0
FY WGS is a lightweight, yet feature-rich, wearable 3 axis gimbal capable of capturing immersive and fully stabilized footages. It is compatible with
GoPro HERO4 Session and other cameras with the same dimensions.
The FY WGS is a miniaturized version of the best-selling FeiYu gimbal, offering exceptional stabilization technology in a wearable form factor for
action cameras. A GoPro T-Clamp adapter is packaged with every FY WGS. Users can attach the gimbal to any accessories supporting the GoPro
three-prong mount. The FY WGS also contains two 1/4" tripod mounts on its gimbal body, allowing the gimbal to be mounted in different orientations
to all universal tripod screw mount accessories (including helmets, bikes, selfie sticks and other accessories).
Operation
LED Status
Function
* When the gimbal is in the Inverted Mode it will revert back to the original orientation after three press.
When the battery is low, the gimbal will make three beeping sound and automatically shut down itself.
Turn On And Switch To
The Mode’s LED Status
Turn Off After
A moment
Power On
Shutdown
The LED light will flash distinctively to indicate different operating modes.
Switch between different operating modes by pressing the function button.
Remove the screws on the
battery compartment,
insert two16340 batteries
and tighten the screws.
Mount the camera carefully
to the mounting bracket
and tighten the screws.
Function
Button
Function
Button
Operating Modes and Functions
Operating Modes and Functions
Function Button
（ ON / OFF ）
Tilting Axis
Rolling Axis
Panning Axis
Function
Interface
1/4 Inch
Screw Hole
1/4 Inch
Screw Hole
Screws For
The Battery
Compartment
T-Clamp
Screw Hole
T-Clamp
Screw Hole
T-Clamp
Screw Hole
Introduction
Install
4
Accessories
Operation
1
STEP 1
STEP 2
STEP 3
POWERING
ON / OFF
Use the 3M Adhesive to fix the bottom of the Gimbal.
Use GoPro Accessories, mount the provided T-clamp to the side
or the bottom of the gimbal. Attach T-clamp to any accessories
supporting the standard GoPro three-prong mount.
The gimbal can also be mounted directly to other accessories
using the standard 1/4" tripod mount. Tighten all screws and
ensure it is firmly mounted before using the gimbal.
USB Cable
USB Connector
How to Charging
USB Cable
FY WGS 3 Axis Wearable Gimbal is compatible with Gopro HERO4 Session
Do not power on the
gimbal before completing
all the installation steps.
Do not power on the
gimbal before completing
all the installation steps.
!
WARNING !
WARNING !
Camera stays in its current orientation. All panning, tilting and rolls are restricted.
Mode #1
- Panning Mode
Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.
Mode #2
- Panning and Tilting Mode
Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.
Mode #3
- Lock Mode
Inversion Mode
Pressing the function button three consecutive times in any operating mode, the gimbal will switch to the
Inverted Mode (Allowing the user to flip the gimbal orientation upside down). Pressing the function button three more times
while in Inverted Mode to switch back to the original orientation.
Manual Pulling Locking
After the gimbal has been powered on for eight seconds, the tilt angle can be adjusted manually in the Panning
Mode and the Lock Mode. Adjust the title angle to the desired position and wait for 0.5 second until the gimbal registers the new angle.
Tilt and Level Calibration
By using the optional FY remote control, tilt and level can be adjusted without connection to a computer.
For more information, please refer to FY remote control section in the instruction manual.
Reset
Pressing the function button four consecutive times will reset the gimbal to initial orientation.
Long Press
For 1 Second
Long Press
For 2 Second
Long Press
For 3 Second
On Constantly
Operation
LED Status
Function Explanation
Lock Mode
Function Button Quick Reference
Double Tap
Single Tap
LED Flashes Once
LED Flashes Twice
Panning Mode
Panning and Tilting Mode
Triple Tap
LED Flashes Once
Inversion Mode
Quadruple Tap
LED Flashes Once
Reset
Charger
Input: DC 5V Min 800mA
Output: DC 4.2V
Type: 16340
M2 * 6mm
Rechargeable Battery
Long screw
M 1.5 Allen Key
T-Clamp
Quick-Release
Buckle
Curved Adhesive
Mounts
3M Adhesive
5V USB Power
Adapter
（Not Included）
HexagonalSocket
HeadCap Screw
Forward
Inverted
Vertical
Camera In Right
Camera In Right
Camera In
Right
Camera in Left
Camera in Left
Camera in Left
Please choose one way:
1
2
3
Rolling
Tilting
Panning
Function
Button
Hexagonal Socket
Head Cap Screw
T-Clamp
Accessories For
1/4 Inch Screws
2
3
Long screw
3M
Adhesive
1
Power on: Ensure the camera is mounted securely, then hold down the function
button for 2 seconds to turn on the gimbal.
Power off: Hold down the function button for 3 seconds to turn off the gimbal.